JKP36005 General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Burnt out element
4 of 6 people
found this instruction helpful.
-
Joe from TABERNACLE, NJ
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
As instructed in your directions
Was this helpful?
Thank you for voting!
broiler element circuit broke
3 of 4 people
found this instruction helpful.
-
James from Lafayette, CO
- Easy
- 30 - 60 mins
-
Nutdriver, Socket set
First removed oven door, according to Reader's Digest repair manual, then removed two screws holding element. Pulled element out several inches, then removed one side of bracket holding up front of element so that bad element could be pulled further out. Then disconnected two red wires from one side and two light blue wires from other sid
... Read more
e. Removed old Element. Attached two light blue wires to one side and two red wires to other pole, inserted element back into rear wall and attached with two screws, Re-attached bracket holding up front of element. Re-installed door. Tested and it worked fine.
Read less
Was this helpful?
Thank you for voting!
Burnt bake element
3 of 4 people
found this instruction helpful.
-
James from SPARTANBURG, SC
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers, Screw drivers
Removed door. Take out two hold down screws for element. Hold electrical tab with pliers and remove screw on each tab. Reverse directions to reinstall. Door may have screws to remove.
Was this helpful?
Thank you for voting!
second time repaired in about ten years
3 of 4 people
found this instruction helpful.
-
william from CLAYMONT, DE
- Very Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
removed parts from carton,,shut off breaker to over,,cradled the flash light,removed cover plate,,removed element,,removed screws from wires,,reversed to install,,screwed wires to element,,placed element in place and installed plate nuts,,,turned breaker back on...
Was this helpful?
Thank you for voting!
timer knobs missing
5 of 11 people
found this instruction helpful.
-
Doris from Redwood City, CA
- Really Easy
- Less than 15 mins
Just pushed the new timer knobs onto the stem. They fit and now I can set the oven timer without having to use a pair of pliers to grip the stem and turn it.
Two of the knobs fit perfectly.
The stem for the the clock was broken off and there was not enough of the stem left for the new knob to fit.
Two of the knobs fit perfectly.
The stem for the the clock was broken off and there was not enough of the stem left for the new knob to fit.
Was this helpful?
Thank you for voting!
Broiler unit burned out
3 of 5 people
found this instruction helpful.
-
Phillip from Charlotte, NC
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver
I removed the unit easily with anut driver, however the unit also supported the thermo-link. I had to use the hack saw to relieve a small opening for the thermo-link to pass through. No real problem. Then a few holes to be drilled to attach the 'link' to the base of the broiler unit.
BUT-I went into the website listed on the bo ... Read more x. GEAppliances.com Guess what? Their price was twice yours!!
BUT-I went into the website listed on the bo ... Read more x. GEAppliances.com Guess what? Their price was twice yours!!
Read less
Was this helpful?
Thank you for voting!
broiler element was broken
2 of 2 people
found this instruction helpful.
-
Milli from AURORA, CO
- Difficult
- More than 2 hours
-
Pliers, Screw drivers, Socket set
I looked on Youtube for a how to video. It was accurate but the screws in my oven were NOT phillips head screws, they turned out to be sheet metal screws. I used pliers at first which was a PAIN but then I borrowed a socket wrench from the neighbor that was MUCH better!! I had wanted to do it myself to prove to my husband and son that I c
... Read more
ould but I ended up needing their help because the screws were so tight.... But we did the repair ourselves!!!
Read less
Was this helpful?
Thank you for voting!
Broiler element stopped heating
3 of 5 people
found this instruction helpful.
-
Steve from Fort Worth, TX
- A Bit Difficult
- 1- 2 hours
-
Screw drivers
Broiler element arrived at my door 3 days after ordering which was nice. Apparently the billing dept. is out of the USA so don't be surprised, like I was, to find a suspicious looking charge for a currency exchange fee (mine was 42 cents). I had to drill two new screw holes in the base of the new element in order for it to fit my oven.
... Read more
I also had to use heavy wire snips to cut off about an inch of the top of the new element base. The female electrical connections also had to be spread out with needle nose pliers since the new element connections were slightly thicker. With all of the issues I had I was frustrated and it took about two hours. On the other hand, the part works perfectly and was priced right. Hopefully it will fit perfectly out of the box for your oven.
Read less
Was this helpful?
Thank you for voting!
Simple, unscrew and then re-screw
2 of 3 people
found this instruction helpful.
-
Carol from Evergreen Park, IL
- Really Easy
- 15 - 30 mins
-
Screw drivers
Simple, unscrew and then re-screw
Was this helpful?
Thank you for voting!
Bake element burned out
2 of 3 people
found this instruction helpful.
-
JoAnn from RICHARDSON, TX
- Very Easy
- 15 - 30 mins
-
Pliers, Wrench (Adjustable)
Turned off power. Then loosened two nuts at back of oven. Pulled out old element and inserted new element. Tightened two nuts and turned power back on.
Was this helpful?
Thank you for voting!
Bake element burned out
1 person
found this instruction helpful.
-
Bill from Yucca Valley, CA
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Removed 4 scews from old element and replaced the old element with the new element with the supplyed new screws. It was very easy. The new element works great.
Was this helpful?
Thank you for voting!
Replaced bake element after first one burnt out
1 person
found this instruction helpful.
-
Gene from Kingwood, TX
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
The replacement was simple. I turned off the power to the oven, took out two nuts holding the element in place, unscrewed the element from the power and finished the job in 10 minutes. The company that we called was going to charge nearly $200 to complete this job. I saved a lot of money by doing it my self.
Was this helpful?
Thank you for voting!
Bake element failed (broke in two)
1 person
found this instruction helpful.
-
Gilda from Newport News, VA
- Really Easy
- Less than 15 mins
-
Nutdriver
Used a nut driver to remove two hex screws holding element to the back of the oven and then the two hex screws connecting the element to the oven wires. I pulled the element out and reversed the process. I turned the oven on and made sure the element worked.
Was this helpful?
Thank you for voting!
Oven wouldn't heat
2 of 4 people
found this instruction helpful.
-
Peter from Sacramento, CA
- Really Easy
- Less than 15 mins
-
Nutdriver
First I shut off the circuit breaker for the oven then removed the screws that hold the element in place. The element was pulled out about 3 inches and unscrewed the 2 screws to disconnect the two wires. Upon receipt of the new element, I simply reversed the above process and the oven performed like new. Very easy, very quick and very
... Read more
grateful to have the oven operating again and it was a very inexpensive fix.
Read less
Was this helpful?
Thank you for voting!
Element had a piece break off of it
1 person
found this instruction helpful.
-
patrick from landing, NJ
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires
the Replacement fit easily. Part was delivered the day after ordering even though I used normal delivery. Oven broke on a Thursday,ordered the part Friday morning, back in operation on Saturday
the Replacement fit easily. Part was delivered the day after ordering even though I used normal delivery. Oven broke on a Thursday,ordered the part Friday morning, back in operation on Saturday
Was this helpful?
Thank you for voting!