All Installation Instructions for General Electric Range JGS968SEK2SS

Our bottom drawer support broke and the bottom drawer was canted

Robert from Woodinville, WA
Really Easy
Less than 15 mins
Screw drivers

Simply removed drawer and lined up the newsupports. Made sure the guide pin was lined up and installed with single screw

Was this helpful?

Broiler and Burners would light, oven would not light and you could smell gas, also before the oven stopped working the oven was taking awhile before it would light

Keith from San Diego, CA
Really Easy
Less than 15 mins
Nutdriver

1.Removed the oven door. 2. Removed the oven floor panel ( slides right out ). 3. Removed cover plate and and removed one screw holding the igniter in place. 4 was able to pull the wire into the oven and unplug the igniter. Ordered a oven temp sensor but never needed it.

Other Parts Used:

Oven Igniter

Temperature Sensor

Was this helpful?

Oven Probe broke

Kathleen from Munt Laurel, NJ
Really Easy
Less than 15 mins

Ordered new probe

Was this helpful?

Hard to move drawer in and out because the rear drawer supports broke off.

Steven from Lansdale, PA
Really Easy
Less than 15 mins
Screw drivers

Repair was very easy - less than a few minutes - just had to screw in 2 screws to the new drawer supports.

Was this helpful?

oven not warming, f2 indicating overheat

David from Lisle, IL
Really Easy
Less than 15 mins
Nutdriver

Removed 4 screws from back panel, disconnected small electricsl connector from sensor, removed one mounting screw from sensor inside oven,pulled wires through and removed old sensor. Fed wires for new sensor through and connected electrical connector, installed panel, installed mounting screw on sensor and checked oven, worked like a cham ... Read more

Read less

Was this helpful?

the grate foots came off

Sandra from Watertown, MA
Really Easy
Less than 15 mins

put it in but it keeps falling out. they're made narrower than my oven grate.

Was this helpful?

Burners are supposed to burn with a blue flame. Two burners had yellow flames

Don from Port Orchard, WA
Really Easy
Less than 15 mins

New burner Heads repaired the two yellow burning units. I believe heat caused the old heads to become. warped over time.

Was this helpful?

missing meat thermistor

John R from Asheville, NC
Really Easy
Less than 15 mins

plug in thermistor when needed

Was this helpful?

Stove drawer rear guides broken

Robert from Shakopee, MN
Really Easy
Less than 15 mins
Nutdriver

Installed new guides with a nut driver without any problems.

Was this helpful?

gasket on door was brittle

Barbara from Bethesda, MD
Really Easy
Less than 15 mins

I feel like Macho Mom. I called in the repair guy since I was afraid of dealing with the gas. HE repaired one item but could tell I was comfortable fixing things and pointed out that the gasket was brittle and would cause major problems if not replaced. Took longer to order the part than do the repair, don't know what I was afraid of!

Was this helpful?

warped burner

judith from boardman, OH
Easy
Less than 15 mins

reinstalled new one. just a little better than than the warped one.

Was this helpful?

Range lower drawer would not stay on track.

Richard from Newark, DE
Really Easy
Less than 15 mins
Nutdriver

Easy to install replacement parts using the screws provided.

Was this helpful?

Broken drawer support

Mario from Deer Park, WA
Really Easy
Less than 15 mins
Nutdriver

Followed the example picture on the part bag. Anyone could do this, incredibly easy. Took about 4 minutes to install both sides.

Was this helpful?

rear drawer supports broke

TERRY from RICHMOND, VA
Really Easy
15 - 30 mins
Socket set

Directtions were by diagram only, no written instructions. Drawing was small and difficult to follow but the repair itself was easy.

Was this helpful?

faulty igniter

Gino from glen ellyn, IL
Easy
15 - 30 mins
Screw drivers, Wrench set

No response from GE website (very disappointing). google "repair GE gas range igniter" and very simple step-by-step instructions...apparently is very common with GE appliances...even mine that was less than 14 months old. Service tech would have charged $300. Did it myself for $80

Was this helpful?

JGS968SEK2SS General Electric Range - Instructions