EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

JGS968KEKC General Electric Range - Instructions

All Instructions for the JGS968KEKC
91 - 105 of 143

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
oven not warming, f2 indicating overheat
  • David from Lisle, IL
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Removed 4 screws from back panel, disconnected small electricsl connector from sensor, removed one mounting screw from sensor inside oven,pulled wires through and removed old sensor. Fed wires for new sensor through and connected electrical connector, installed panel, installed mounting screw on sensor and checked oven, worked like a cham p. Took 5 minutes.
Was this helpful?
Thank you for voting!
the grate foots came off
  • Sandra from Watertown, MA
  • Really Easy
  • Less than 15 mins
put it in but it keeps falling out. they're made narrower than my oven grate.
Was this helpful?
Thank you for voting!
Plastic slide for storage drawer broken.
  • James from Stuart, VA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Took part out of package, looked at instructions and followed them. Required a screwdriver to screw part on to the drawer.
Was this helpful?
Thank you for voting!
Our bottom drawer support broke and the bottom drawer was canted
  • Robert from Woodinville, WA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Simply removed drawer and lined up the newsupports. Made sure the guide pin was lined up and installed with single screw
Was this helpful?
Thank you for voting!
Broiler and Burners would light, oven would not light and you could smell gas, also before the oven stopped working the oven was taking awhile before it would light
  • Keith from San Diego, CA
  • Really Easy
  • Less than 15 mins
  • Nutdriver
1.Removed the oven door. 2. Removed the oven floor panel ( slides right out ). 3. Removed cover plate and and removed one screw holding the igniter in place. 4 was able to pull the wire into the oven and unplug the igniter. Ordered a oven temp sensor but never needed it.
Was this helpful?
Thank you for voting!
Hard to move drawer in and out because the rear drawer supports broke off.
  • Steven from Lansdale, PA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Repair was very easy - less than a few minutes - just had to screw in 2 screws to the new drawer supports.
Was this helpful?
Thank you for voting!
Flashing F2 and erratic temperature readings.
  • Kenneth from Salem, OR
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Unplugged from wall outlet, then opened oven front door. Reached in and removed two screws. Pulled oven sensor threw and detached electrical connector from old sensor. Plugged in new oven sensor and reversed removal procedure. No more Flashing F2 and oven temperature came to ready. Very easy.
Was this helpful?
Thank you for voting!
Missing grate foot.
  • Barbara J from Sweetwater, TX
  • Really Easy
  • Less than 15 mins
  • Pliers
Ordered by phone parts & very pleased with all of transaction.
Was this helpful?
Thank you for voting!
Grate Foot Have 8 For My Stove And One Breaks Every Now And Then
  • Lee from Kenner, LA
  • Really Easy
  • Less than 15 mins
This was and always will be an easy fix, all I have to do is get my ice pick and pick the broken rubber part stuck in the hole if it does not break clean and fall out. Not much more I can say about this simple problem.
Was this helpful?
Thank you for voting!
rear drawer supports broke
  • TERRY from RICHMOND, VA
  • Really Easy
  • 15 - 30 mins
  • Socket set
Directtions were by diagram only, no written instructions. Drawing was small and difficult to follow but the repair itself was easy.
Was this helpful?
Thank you for voting!
faulty igniter
  • Gino from glen ellyn, IL
  • Easy
  • 15 - 30 mins
  • Screw drivers, Wrench set
No response from GE website (very disappointing). google "repair GE gas range igniter" and very simple step-by-step instructions...apparently is very common with GE appliances...even mine that was less than 14 months old. Service tech would have charged $300. Did it myself for $80
Was this helpful?
Thank you for voting!
Stove top worked, Broiler worked, but Oven would not heat
  • Vaughn from Visalia, CA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Odered igniter from part select, it arrived the next day. Removed oven door removed heat shield on bottom of oven and there it was. Removed the two screws pulled the wires till the connector came through, unpluged connector, plugged in new igniter, repaced everything and Bam, we were cooking. Did not even have to pull oven out from the wa ll. Super easy.
Was this helpful?
Thank you for voting!
The oven temperature could not be controlled
  • Keith from Annapolis, MD
  • Easy
  • 15 - 30 mins
  • Nutdriver, Socket set
Disconnect the range from the mains. Open the door. Remove the single screw holding the temperature sensor - this is located on the back wall on center and is screwed to the broiler mounting plate. Remove the four screws holding the boiler element and allow it to hang down on the wire; this exposes a space to feed the wire through later. Now move to the back of the range and remove the six screws that hold the central cover plate. Now push the insulation to up out of the way and you can disconnect the temperature sensor, pull it out through front, insert the new one and connect it. Reassemble in the reverse order. Mine worked perfectly!
Was this helpful?
Thank you for voting!
Oven slow to heat up
  • Joe from Harkers Is., NC
  • Easy
  • 15 - 30 mins
  • Nutdriver
Removed oven door. Removed 2 screws from heat sensor on rear upper wall of oven. Pulled unit out to access rear of unit. Removed six screws on shield on back of unit. Dis connected heat sensor wire and pulled old sensor through from inside of oven. Feed wire of new sensor through from inside and plug in. Everything in reverse. I also had the gas(propane) company come out and check the pressure coming out of the "low pres." regulator. It was low, they changed the regulator.
Was this helpful?
Thank you for voting!
Oven would not light due to igniter.
  • Robert from Hillsboro, WV
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
After reading reviews about corroded screws causing difficult removal I sprayed penetrating oil prior to installing replacement part. The oven doesn't need to be pulled out to fix. Just carefully pull wires through hole until the locking plug is visible & swap out. Very easy repair.
Was this helpful?
Thank you for voting!
All Instructions for the JGS968KEKC
91 - 105 of 143