EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

JGP945BEKB General Electric Range - Instructions

All Instructions for the JGP945BEKB
16 - 30 of 37

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
some of electrodes not working at times,found were bad,wires had some insulation missing, clips looked burnt,found all new parts replaced
1 person found this instruction helpful.
  • Dana from LEEDS, AL
  • Really Easy
  • More than 2 hours
  • Pliers
the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.
Was this helpful?
Thank you for voting!
very easy
1 of 2 people found this instruction helpful.
  • ROBERT from CYPRESS, TX
  • Really Easy
  • Less than 15 mins
there were no grate pads so it was easy to add them.
Was this helpful?
Thank you for voting!
The electrode had broke
1 of 2 people found this instruction helpful.
  • O.Robert from Montrose, PA
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
I unscrewed the base where the electrode was attached to detached the electrode detached the wire to the electrode inserted new electrode with holding spring and clamp attached wire to electrode.
I then put the base back on top and screwed in the two screws assembled the remaining parts and turned on the stove unit and it worked I am very happy.
Was this helpful?
Thank you for voting!
The Grate foot is to big for the hole.
1 of 2 people found this instruction helpful.
  • Harold from Broadalbin, NY
  • A Bit Difficult
  • 15 - 30 mins
I had to drill the hole to a larger size to enable the foot to fit.
Was this helpful?
Thank you for voting!
Hot burner light lens broke off.
1 of 2 people found this instruction helpful.
  • Charles from NEKOOSA, WI
  • Easy
  • 15 - 30 mins
  • Screw drivers
Pull range away from back wall. Remove panel behind control knobs by removing the screws that hold it on. Find hot burner light that holds lens. Remove broken part of lens. Insert new lens into hole on front of control panel and into hot burner light receptacle. Replace back panel. Slide range back into place.
Was this helpful?
Thank you for voting!
worn and pitted burner caps
2 of 5 people found this instruction helpful.
  • Ann from Ashland, MA
  • Really Easy
  • Less than 15 mins
Removed the old caps and replaced with new burner caps. The stove top looks brand new. Thank you.
Was this helpful?
Thank you for voting!
The Grate Foot was deteriorated on several sections for my cook top. The hardest part was finding the right part.
1 of 3 people found this instruction helpful.
  • Chelagh from Fredericksburg, VA
  • Really Easy
  • Less than 15 mins
Nothing technical.
Was this helpful?
Thank you for voting!
To Replace Gas And Burner Parts In Section 4
0 of 1 people found this instruction helpful.
  • John from Long Beach, NY
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers, Wrench set
Start by removing all screws 3 for each burner total of 15 t-15 bit is required then proceed to remove spark igniters 5 total slight pull next step would be to slide a screwdriver under top left and right side to remove top shelf. There you will have access to the parts you need to replace. When done just reverse installation instruction s to complete
Was this helpful?
Thank you for voting!
Grate foot bdroke off allowing grate to scratch cooktop
0 of 1 people found this instruction helpful.
  • John from Tijeras, NM
  • Really Easy
  • Less than 15 mins
Used scribe to remove grate foot plug still in grate inserted new foot.
Was this helpful?
Thank you for voting!
Leaking from front door
1 of 9 people found this instruction helpful.
  • Gene from Simi Valley, CA
  • Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
First remove the screws around the inside perimeter of the door. These require a special hex driver. Take off the inside plastic liner of door.
Peal off the old Insulation Foam Strip and replace it with the new strip in the same location. Make sure the wires are off to the right side. Replace the door plastic liner. Done. The In sulation Foam Strip really acts more like a loose gasket to keep spashing from creeping under the door and drippin out on the floor.
Was this helpful?
Thank you for voting!
The spark module would constantly spark
  • Douglas from Knoxville, TN
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I ordered the spark module and replaced it which was veru simple, plugged it in and it sparked only now and again. I finally said forget it and it has now stopped sparking but for how long I do not know.
Was this helpful?
Thank you for voting!
no
  • yihui from clarksburg, MD
  • Really Easy
  • Less than 15 mins
  • Nutdriver
it is easy
Was this helpful?
Thank you for voting!
Grate Foot Have 8 For My Stove And One Breaks Every Now And Then
  • Lee from Kenner, LA
  • Really Easy
  • Less than 15 mins
This was and always will be an easy fix, all I have to do is get my ice pick and pick the broken rubber part stuck in the hole if it does not break clean and fall out. Not much more I can say about this simple problem.
Was this helpful?
Thank you for voting!
Missing grate foot.
  • Barbara J from Sweetwater, TX
  • Really Easy
  • Less than 15 mins
  • Pliers
Ordered by phone parts & very pleased with all of transaction.
Was this helpful?
Thank you for voting!
Stain/polyurethane dried on burner head & cap
  • Stephen from Ogdensburg, NY
  • Really Easy
  • Less than 15 mins
Lifted both pieces off and placed the new ones on,turned on the burner and it worked as it should.
Was this helpful?
Thank you for voting!
All Instructions for the JGP945BEKB
16 - 30 of 37