Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
burner would not lite
23 of 34 peoplefound this instruction helpful.
Glen from Kenner, LA
Really Easy
Less than 15 mins
Screw drivers
openend stove top disconnected wire pushed out old sparker inserted new one closed lid game over
Was this helpful?
Thank you for voting!
Change bad/broken igniter on gas stove top burners
6 of 6 peoplefound this instruction helpful.
James from Kaplan, LA
Really Easy
Less than 15 mins
Very simple repair with no tools required. Turn off power to stove. Remove grates, remove burner, pull old Top Burner Spark Electrode up being careful not to jerk it up hard - wiggle if necessary, unplug wire from old electrode, plug wire into new electrode making sure it fits snug - if not, squeeze it closed a little at a time until it f
... Read moreits snug, push new igniter into place being careful not to force it and crack the ceramic body. Install burner being careful not to damage the electrode, Install grates. Turn power back on and test to make sure it works. It took me all of 15 minutes to change 2 burner spark electrodes. The only bad thing about this repair is that the shipping costs as much as the parts.
Read less
Was this helpful?
Thank you for voting!
Burnt burner
7 of 12 peoplefound this instruction helpful.
Janine from Wind Gap, PA
Really Easy
Less than 15 mins
Just put it on. Quite proud of myself for figuring out what and how to get the part however! The website was very helpful.
Was this helpful?
Thank you for voting!
Needed To Replace Burner
5 of 6 peoplefound this instruction helpful.
Robert K from York, PA
Really Easy
Less than 15 mins
Took longer to open the box.
Was this helpful?
Thank you for voting!
Burner on stove not working correctly
4 of 6 peoplefound this instruction helpful.
Trevor from Eldersburg, MD
Really Easy
Less than 15 mins
Order parts and installed - no tools needed - completed repairs less than 1 minute
Was this helpful?
Thank you for voting!
Gas range igniter was making a clicking sound every 3 to 5 minutes, as if it was trying to ignite one of the burners.
3 of 3 peoplefound this instruction helpful.
Wesley from FRANKLIN, TN
Really Easy
15 - 30 mins
Pliers
Unplug the range from its wall socket to avoid electric shock. The various range parts that support a pot or frypan are easily lifted off their perches, exposing the small white igniter. The only moderately difficult aspect is wiggling the igniter out of its retainer. The electric wire leading into it then can be pulled out and fed int
... Read moreo the new igniter with a push. Replace igniter in its retainer, then replace the range parts you removed to expose the igniter and plug the range back into the wall socket. Piece of cake.
Read less
Was this helpful?
Thank you for voting!
The burner caps were chipped and discolored.
2 of 2 peoplefound this instruction helpful.
Anne from OSSINING, NY
Very Easy
Less than 15 mins
I merely replaced the old caps with the new ones. It couldn't have been easier!
PLEASE BE ADVISED WHEN THEY SHIPPED THE BACK ORDER 1 -(taupe) LARGE CAP - RECEIVED 4 BLACK CAPS - 1-SMALL 2-MEDIUM 1-LARGE (ALL BLACK) - STILL LOOKING FOR A LARGE CAP IN taupe color!
Received refund for 1-large cap PROBLEM IS ALL OTHER PARTS ON THE GAS STOVE ARE taupe in color - do not want black!
... Read morer />your advice?
some of electrodes not working at times,found were bad,wires had some insulation missing, clips looked burnt,found all new parts replaced
1 personfound this instruction helpful.
Dana from LEEDS, AL
Really Easy
More than 2 hours
Pliers
the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.
Was this helpful?
Thank you for voting!
To Replace Gas And Burner Parts In Section 4
0 of 1 peoplefound this instruction helpful.
John from Long Beach, NY
A Bit Difficult
30 - 60 mins
Pliers, Screw drivers, Wrench set
Start by removing all screws 3 for each burner total of 15 t-15 bit is required then proceed to remove spark igniters 5 total slight pull next step would be to slide a screwdriver under top left and right side to remove top shelf. There you will have access to the parts you need to replace. When done just reverse installation instruction
... Read mores to complete
Read less
Was this helpful?
Thank you for voting!
Large burner wasn't lighting very quickly
Jesse from Nashville, TN
Easy
30 - 60 mins
Removed grill grates, gas distributors, etc. (just lift off). Used star screwdriver to remove screws (3 per burner for SML, 2 for power burner). Lift off stainless cover, which also lifts off the white sparkers I was replacing. Pull them off the wires (didn't need pliers, others said they did). Replace (make sure it is all the way on) and
... Read more reverse your steps. White sparkers electrodes seemed loose when I put them back on, but tightened up when I fully secured the top back on. Make sure the wires aren't pinched underneath when you put the top back on. Recommended: If you've got one that isn't working, go ahead and replace all 3 (power burner is different) because the part is so cheap you may as well just do it now.
Read less
Was this helpful?
Thank you for voting!
Chipping around edges of Burner Caps
Howard from Yorba Linda, CA
Really Easy
Less than 15 mins
Received the parts very expeditiously(2 days from time of placing the order), and the replacing of the caps was a "no brainer".
Could not have been simpler. Burner head dropped into place and was held in place by gravity. Not possible for part to go in incorrectly.
Was this helpful?
Thank you for voting!
Replace medium burner for gas cooktop
Charles from Houston, TX
Really Easy
Less than 15 mins
Very easy to remove grates, burner cover and remove old burner head. Very simple process, but surprised that there was no efficient way to clean carbon deposits from my old burner. Burner video instructions on line insured I installed the new burner head correctly (actually, pretty hard to get wrong), and burner worked correctly immediate
... Read morely. Will likely replace other burners in time as the new one is so "silvery" colored compared to my other burners.
My Orders
