- Home
- JGP628BEKB
- Instructions
JGP628BEKB General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
some of electrodes not working at times,found were bad,wires had some insulation missing, clips looked burnt,found all new parts replaced
1 person
found this instruction helpful.
-
Dana from LEEDS, AL
- Really Easy
- More than 2 hours
-
Pliers
the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.
Was this helpful?
Thank you for voting!
The Grate foot is to big for the hole.
1 of 2 people
found this instruction helpful.
-
Harold from Broadalbin, NY
- A Bit Difficult
- 15 - 30 mins
I had to drill the hole to a larger size to enable the foot to fit.
Was this helpful?
Thank you for voting!
very easy
1 of 2 people
found this instruction helpful.
-
ROBERT from CYPRESS, TX
- Really Easy
- Less than 15 mins
there were no grate pads so it was easy to add them.
Was this helpful?
Thank you for voting!
The Grate Foot was deteriorated on several sections for my cook top. The hardest part was finding the right part.
1 of 3 people
found this instruction helpful.
-
Chelagh from Fredericksburg, VA
- Really Easy
- Less than 15 mins
Nothing technical.
Was this helpful?
Thank you for voting!
Grate foot bdroke off allowing grate to scratch cooktop
0 of 1 people
found this instruction helpful.
-
John from Tijeras, NM
- Really Easy
- Less than 15 mins
Used scribe to remove grate foot plug still in grate inserted new foot.
Was this helpful?
Thank you for voting!
To Replace Gas And Burner Parts In Section 4
0 of 1 people
found this instruction helpful.
-
John from Long Beach, NY
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers, Wrench set
Start by removing all screws 3 for each burner total of 15 t-15 bit is required then proceed to remove spark igniters 5 total slight pull next step would be to slide a screwdriver under top left and right side to remove top shelf. There you will have access to the parts you need to replace. When done just reverse installation instruction
... Read more
s to complete
Read less
Was this helpful?
Thank you for voting!
Leaking from front door
1 of 9 people
found this instruction helpful.
-
Gene from Simi Valley, CA
- Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
First remove the screws around the inside perimeter of the door. These require a special hex driver. Take off the inside plastic liner of door.
Peal off the old Insulation Foam Strip and replace it with the new strip in the same location. Make sure the wires are off to the right side. Replace the door plastic liner. Done. The In ... Read more sulation Foam Strip really acts more like a loose gasket to keep spashing from creeping under the door and drippin out on the floor.
Peal off the old Insulation Foam Strip and replace it with the new strip in the same location. Make sure the wires are off to the right side. Replace the door plastic liner. Done. The In ... Read more sulation Foam Strip really acts more like a loose gasket to keep spashing from creeping under the door and drippin out on the floor.
Read less
Was this helpful?
Thank you for voting!
The spark module would constantly spark
-
Douglas from Knoxville, TN
- Really Easy
- Less than 15 mins
-
Screw drivers
I ordered the spark module and replaced it which was veru simple, plugged it in and it sparked only now and again. I finally said forget it and it has now stopped sparking but for how long I do not know.
Was this helpful?
Thank you for voting!
Accidentally burned two original knobs
-
Francisco from Cypress, TX
- Really Easy
- Less than 15 mins
Could not get the model number of the cooktop stove. GE hides it very well. But, I found a replacement knob on your web that looked similar to my original. The photo of the replacement was very accurate in terms of showing its true size and configuration of the stem. This photo showed that the prospective replacement would match the origi
... Read more
nal´s configuration and it did. Plus, it was the most inexpensive knob among the ones available in this or other sites. Great site.
Read less
Was this helpful?
Thank you for voting!
Stain/polyurethane dried on burner head & cap
-
Stephen from Ogdensburg, NY
- Really Easy
- Less than 15 mins
Lifted both pieces off and placed the new ones on,turned on the burner and it worked as it should.
Other Parts Used:
Was this helpful?
Thank you for voting!
Burner would not ignite.
-
John from Los Angeles, CA
- Really Easy
- Less than 15 mins
Could not have been simpler. Burner head dropped into place and was held in place by gravity. Not possible for part to go in incorrectly.
Was this helpful?
Thank you for voting!
the grate foots came off
-
Sandra from Watertown, MA
- Really Easy
- Less than 15 mins
put it in but it keeps falling out. they're made narrower than my oven grate.
Was this helpful?
Thank you for voting!
Replace medium burner for gas cooktop
-
Charles from Houston, TX
- Really Easy
- Less than 15 mins
Very easy to remove grates, burner cover and remove old burner head. Very simple process, but surprised that there was no efficient way to clean carbon deposits from my old burner. Burner video instructions on line insured I installed the new burner head correctly (actually, pretty hard to get wrong), and burner worked correctly immediate
... Read more
ly. Will likely replace other burners in time as the new one is so "silvery" colored compared to my other burners.
Read less
Was this helpful?
Thank you for voting!
Grate Foot Have 8 For My Stove And One Breaks Every Now And Then
-
Lee from Kenner, LA
- Really Easy
- Less than 15 mins
This was and always will be an easy fix, all I have to do is get my ice pick and pick the broken rubber part stuck in the hole if it does not break clean and fall out. Not much more I can say about this simple problem.
Was this helpful?
Thank you for voting!
Large burner wasn't lighting very quickly
-
Jesse from Nashville, TN
- Easy
- 30 - 60 mins
Removed grill grates, gas distributors, etc. (just lift off). Used star screwdriver to remove screws (3 per burner for SML, 2 for power burner). Lift off stainless cover, which also lifts off the white sparkers I was replacing. Pull them off the wires (didn't need pliers, others said they did). Replace (make sure it is all the way on) and
... Read more
reverse your steps. White sparkers electrodes seemed loose when I put them back on, but tightened up when I fully secured the top back on. Make sure the wires aren't pinched underneath when you put the top back on. Recommended: If you've got one that isn't working, go ahead and replace all 3 (power burner is different) because the part is so cheap you may as well just do it now.
Read less
Was this helpful?
Thank you for voting!