Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Igniter constantly ticking ...
2 of 2 peoplefound this instruction helpful.
steve from BEAVERCREEK, OH
Easy
15 - 30 mins
Pliers, Socket set
Unplug!! Pull knobs Pull burner centers Unscrew the nut at the center of each burner Tilt cover up revealing under burner controls Remove old harness Install new harness Reassemble in reverse order Plug in NO ticking
Was this helpful?
Thank you for voting!
Rubber Grate foot worn or missing.
2 of 3 peoplefound this instruction helpful.
Terry L from Puyallup, WA
Really Easy
Less than 15 mins
Replaced worn or missing Grate Foot with new ones. Took less than 5 minutes.
Was this helpful?
Thank you for voting!
Knobs had melted
2 of 3 peoplefound this instruction helpful.
Martha from DOWNERS GROVE, IL
Very Easy
Less than 15 mins
Pulled out the old. put the new ones on. Easy
Was this helpful?
Thank you for voting!
feet keep falling off
2 of 3 peoplefound this instruction helpful.
Richard from Stratham, NH
Really Easy
Less than 15 mins
Inserted the grate foot into the spot provided; after consulting the parts manuel to insure I was using the proper procedure.
I do use silicone to help hold the foot but it still won't hold
Was this helpful?
Thank you for voting!
Rubber grate foot failed
1 personfound this instruction helpful.
Gary from HENDERSONVLLE, NC
Very Easy
Less than 15 mins
Cut off approx. 1/8" in length for correct fit.
Was this helpful?
Thank you for voting!
Igniters would not turn off
1 personfound this instruction helpful.
Paul from UPLAND, CA
Really Easy
15 - 30 mins
Pliers, Screw drivers
Replaced starter switch harness as well as igniter module. Cost was around $70 for parts. Cheaper than a new cooktop.
REMOVE GRILL AND TOP OF BURNERS. CLEAN GUNK OUT OF TORQUE SCREWS AND TRIED TO REMOVE TOP PLATE. FOUND IGNITERS ALSO NEED TO COME OUT, THEY HAD HEAVY DEPOSIT, BE CAREFUL. ONCE I GOT THEM OUT, JOB WENT WELL. NOTE MAKE SURE ALL CONNECTION ARE CLEANED BEFORE REASSEMBLY.
some of electrodes not working at times,found were bad,wires had some insulation missing, clips looked burnt,found all new parts replaced
1 personfound this instruction helpful.
Dana from LEEDS, AL
Really Easy
More than 2 hours
Pliers
the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.
Was this helpful?
Thank you for voting!
The Grate foot is to big for the hole.
1 of 2 peoplefound this instruction helpful.
Harold from Broadalbin, NY
A Bit Difficult
15 - 30 mins
I had to drill the hole to a larger size to enable the foot to fit.
Was this helpful?
Thank you for voting!
very easy
1 of 2 peoplefound this instruction helpful.
ROBERT from CYPRESS, TX
Really Easy
Less than 15 mins
there were no grate pads so it was easy to add them.
Was this helpful?
Thank you for voting!
The Grate Foot was deteriorated on several sections for my cook top. The hardest part was finding the right part.
1 of 3 peoplefound this instruction helpful.
Chelagh from Fredericksburg, VA
Really Easy
Less than 15 mins
Nothing technical.
Was this helpful?
Thank you for voting!
Grate foot bdroke off allowing grate to scratch cooktop
0 of 1 peoplefound this instruction helpful.
John from Tijeras, NM
Really Easy
Less than 15 mins
Used scribe to remove grate foot plug still in grate inserted new foot.
Was this helpful?
Thank you for voting!
To Replace Gas And Burner Parts In Section 4
0 of 1 peoplefound this instruction helpful.
John from Long Beach, NY
A Bit Difficult
30 - 60 mins
Pliers, Screw drivers, Wrench set
Start by removing all screws 3 for each burner total of 15 t-15 bit is required then proceed to remove spark igniters 5 total slight pull next step would be to slide a screwdriver under top left and right side to remove top shelf. There you will have access to the parts you need to replace. When done just reverse installation instruction
... Read mores to complete
Read less
Was this helpful?
Thank you for voting!
Leaking from front door
1 of 9 peoplefound this instruction helpful.
Gene from Simi Valley, CA
Easy
Less than 15 mins
Nutdriver, Screw drivers
First remove the screws around the inside perimeter of the door. These require a special hex driver. Take off the inside plastic liner of door. Peal off the old Insulation Foam Strip and replace it with the new strip in the same location. Make sure the wires are off to the right side. Replace the door plastic liner. Done. The In
... Read moresulation Foam Strip really acts more like a loose gasket to keep spashing from creeping under the door and drippin out on the floor.
My Orders
