JGBS23WELW General Electric Range - Instructions

I had to pull the drawer to get to the burner, then remove the heat shield to get to the connections. I took out the screw at the end of the burner tube, then the two screws holding the tube to the back wall. I had to pull the connections through the back wall of the oven, and disconnect them. I then removed the two screws holding the ... Read more igniter to the old tube, and used them to connect the new igniter to the new tube. At that time, I also had to cut the old connections off of the old ignighter, and put them on the new one. I also had to redo the connection to the gas valve at the bottom of the tube. I then put all the wire and connections back through the hole in the back of the oven, connect the tube back to the rear of the oven, and the single screw to hold the end of the tube. I replaced the the heat shield, and tested. Everything worked fine.

First I needed the correct model number & the correct part numbers for the two front tube assemblies. After that well.... I removed everything on top of the stove. I then proceded to remove all the torx screws for each orifice holder bracket & igniter wires so i could raise the top lid ( without this step you will wind up replacing more t ... Read more han one tube assembly!) Be careful when removing color coded wires so that they work with the correct burner. Remove compression nut to burner valve... i used a crowfoot. remove orifice holder from bracket & install new holder ( onto bracket). Install orifice assembly to burner valve ( do not over tighten), re-install wires to igniters, lower lid, and re-install torx screws. The correct parts require little effort to align. Last of all, test burners and check for leaks. Thanks for reading, I will continue to learn from my mistakes!

Removed the two screws put the heat shield off the old one onto the new one put new bottom in and tightened two screws. Done #38. 69 Cost of part with shipping cost included.

I was very pleased with how quickly the new oven rack arrived and it was a perfect fit. Thanks.

My son cleaned the stove and scrubbed the numbers off the knob with a Brillo pad. I didn't know what temperature my oven was set for when I turned the oven on. I went online, ordered a knob and it arrived in two days! I took it out the box and put it on...perfect fit! It was a perfect match to my original knob. No tools needed. And the pr ... Read more ice was right.

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

Thanksgiving was coming and I needed extra oven space. So I ordered an additional rack. Installation ... just put it in the oven. My part came the day after I ordered it.

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appl ... Read more iance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

removed two screws and took out bottom tray and put the new one in and replaced the screws.DId it my self.

unplugged the old spark module and plugged the new one in. Disassebled and reassembled the new orifice holder.

1) Turn off power at circuit breaker panel
2) Slide out Range from wall
3) Unplug Range
4) Remove back panel and unplug electrical connections to socket
5) From front of oven, remove glass cover over old oven light bulb and remove flange that holds socket and bulb
6) Remove old socket from mounting flange and disc ... Read more ard.
7) Place new socket into mounting flange
8) Screw mounting flange and new socket into the oven from front. Reattach electrical connections from back.
9) Screw in new light bulb from front
10) Replace existing glass cover over new light bulb and snap wire holder in place
11) Replace back panel
11) Plug in range
12) Slide range back to original position
13) Turn on power
Works like a charm! Thanks for having the parts after 30 years!

opened back panel. noted location of colored wires. disconnected wires & removed module. attache wires to new module & attached module to panel. closed up back panel. tested all burners

Took longer to open the box.

Just put it on. Quite proud of myself for figuring out what and how to get the part however! The website was very helpful.

Replaced old with new.