EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

JGBS07DEM2CC General Electric Range - Instructions

All Instructions for the JGBS07DEM2CC
16 - 30 of 105

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Twice I ordered the oven light bulb & each time the light bulb was defected
18 of 38 people found this instruction helpful.
  • Barbara from BELLEVUE, WA
  • Very Difficult
  • Less than 15 mins
I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appl iance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance
Was this helpful?
Thank you for voting!
Replace Oven light socket and light bulb in kitchen Range
6 of 6 people found this instruction helpful.
  • Ronald from TUCSON, AZ
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set, Wrench set
1) Turn off power at circuit breaker panel
2) Slide out Range from wall
3) Unplug Range
4) Remove back panel and unplug electrical connections to socket
5) From front of oven, remove glass cover over old oven light bulb and remove flange that holds socket and bulb
6) Remove old socket from mounting flange and disc ard.
7) Place new socket into mounting flange
8) Screw mounting flange and new socket into the oven from front. Reattach electrical connections from back.
9) Screw in new light bulb from front
10) Replace existing glass cover over new light bulb and snap wire holder in place
11) Replace back panel
11) Plug in range
12) Slide range back to original position
13) Turn on power
Works like a charm! Thanks for having the parts after 30 years!
Was this helpful?
Thank you for voting!
Oven would not turn off due to inoperative thermostat
7 of 13 people found this instruction helpful.
  • Timothy from Lake Elsinore, CA
  • Easy
  • 15 - 30 mins
  • Screw drivers
1st ensure thermostat is intact, I thought it was broken but upon further investigation I noticed that one of the screws that hold the thermostat in place had came loose which cause the thermostat knob not to be able to turn the thermostat stem. Re-installed thermostat mounting screw and it worked just fine.
Was this helpful?
Thank you for voting!
old blackened oven racks
8 of 17 people found this instruction helpful.
  • Roger from Falls Church, VA
  • Really Easy
  • Less than 15 mins
Replaced old with new.
Was this helpful?
Thank you for voting!
old burner not firing properly
4 of 5 people found this instruction helpful.
  • Michael from New Paltz, NY
  • Really Easy
  • Less than 15 mins
ordered parts, 2 double burners, 3 days later they arrived.opened box.
lift stove top, lift out old burner,placed next to new burner to see if they were the same. THEY WERE. place in new burner, checked to see if burner assembly fit correctly. IT DID.
units purchased were exact replacements. supplied spacer nuts not needed. ... Read more >easy fix looks new again, thanks.
Was this helpful?
Thank you for voting!
Right burners would not ignite.
4 of 5 people found this instruction helpful.
  • David from Pflugerville, TX
  • Easy
  • Less than 15 mins
  • Nutdriver
Remove the cover over the spark module. Remove the two screws holding the module. Unplug the wires from the old module and plug them into the new module. Install the new module with the two screws. Replace the cover.
Was this helpful?
Thank you for voting!
Burners could no longer be cleaned.
3 of 3 people found this instruction helpful.
  • Richard from San Diego, CA
  • Really Easy
  • Less than 15 mins
Lifted the top and dropped in the new burners. Realized they always should have had the leveling washers provided so I took the burners off, dropped on the leveling washers and dropped the burners back on. This all took about 2 minutes. Really made the range top look a lot nicer.
Was this helpful?
Thank you for voting!
Replace Gasket to Oven
3 of 3 people found this instruction helpful.
  • Nancy from BRICK, NJ
  • Very Easy
  • Less than 15 mins
  • Pliers
Removed old gasket, did need to use pliers. However, it was easy. The new gasket just snapped in place ...super easy.
Was this helpful?
Thank you for voting!
none
3 of 3 people found this instruction helpful.
  • Michael from Laughlin, NV
  • Very Easy
  • Less than 15 mins
slid the old ones out and slid the new ones in. done
Was this helpful?
Thank you for voting!
Oven ,Going on/off intermittently" Very Dangerous during day /at night especially when all is asleep /away from home,not knowing!
4 of 6 people found this instruction helpful.
  • Leroy-Anthony from Jamaica, NY
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
To: Remove.Four(4)nuts. Six(6)screws. Two (2) clips. To:Reinstall reverse process. "Very simple stright forward, and most enjoyable."
Was this helpful?
Thank you for voting!
Hard to remove screws & no instructions that a heat shield had to be transferred from old to new
3 of 4 people found this instruction helpful.
  • Peter from REDDING, CT
  • Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set
One of the initial two screws for the oven bottom would not budge. Finally used a socket set to loosen it up. Upon taking out the old bottom I turned it over & saw a heat shield attached. I have no idea if you can order a new bottom with a new shield already attached or not, but I had no idea it was there until I took the old part out. Ou t of the eight screws attaching the shied, four of them were also difficult to loosen up. But in the end the new bottom looks great !
Was this helpful?
Thank you for voting!
Rusted & Dirty Burners
3 of 4 people found this instruction helpful.
  • Tara from Bronx, NY
  • Really Easy
  • Less than 15 mins
I moved to an apartment where the past tenants did not take care of the stove. I think this stove is 10+ years old and looks like it was never cleaned in all of its existance! I cleaned everything really well with oven cleaner and lots of scrubbing. The stove looked brand new except the burners! I couldn't take it anymore so I ordered n ew ones. The burners came in less time than stated. I opened the box, took the burners out, lifted the oven hood and just placed them right where the others were. There are no tools needed it pretty much just gets placed down in the appropriate spot and that's that! No directions or tools needed. My stove looks awesome now!! When you first use the burners, you will probably need to place a match or lighter by the burner to get the fire going. After that, it lights perfectly every time.
Was this helpful?
Thank you for voting!
lights blown out
6 of 14 people found this instruction helpful.
  • Gerald from WINTERVILLE, GA
  • Very Easy
  • Less than 15 mins
replaced lights in refrigirator and freezer
Was this helpful?
Thank you for voting!
oven racks very old and writing on knobs worn ff
2 of 2 people found this instruction helpful.
  • Patricia from SAN JOSE, CA
  • Very Easy
  • Less than 15 mins
Very was ti replace racks and knobs. Very fast mail service
Was this helpful?
Thank you for voting!
No ignition
6 of 14 people found this instruction helpful.
  • Karen from Dale City, VA
  • A Bit Difficult
  • 30 - 60 mins
  • Socket set
The repair was somewhat easy, it would have been easiere if I had figured out the right part in the first place! Replacing the Thermostat is a simple task and actually only took abut 10 minutes. The harder task was replacing the glow bar in the broiler area! What a pain! The part had the same gender connector as the existing wiring. Had t o cut the connectors off and use ceramic wire nuts... should be simple but the wires on the replacement part were about 1/2 inch too short! After some creative manuvering and about an hour of cussing out the OEM part manufacturer it went together and worked OK but I suggest before trying to solve a problem like this remember the basics... always check the obvious first!
Was this helpful?
Thank you for voting!
All Instructions for the JGBS07DEM2CC
16 - 30 of 105