EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

JGB920SEC2SS General Electric Range - Instructions

All Instructions for the JGB920SEC2SS
1 - 15 of 34

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Burner wouldn't light
53 of 63 people found this instruction helpful.
  • Jeffrey from Freehold, NJ
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
I removed the old igniter by working a thin screwdriver under the edge of the igniter, and carefully prying it up. I then used pliers to pull off the electrical wire. Connected up the new igniter, and pushed it back into the hole. A very simple repair.

I've replaced 2 igniters on this stove. My symptoms were that when I tried to light one of the bad burners I heard clicking, and could see the spark on the other (working) burners. So I knew the basic sparking function was working. Just that the igniter on the broken burner would not spark.
Was this helpful?
Thank you for voting!
No spark at one burner
43 of 59 people found this instruction helpful.
  • Michael from Weatogue, CT
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Pliers, Screw drivers
Other writers have claimed that this is a "really easy" job. They apparently had one or more of: 1. Less used appliance. 2. Never spilled anything on the cooktop 3. Much better luck. In my case, the apparently faulty igniter absolutely would not pull out. I removed it by removing the burner retaining screws and prying under the burner cas ting. Having done that, I cleaned the igniter and tested it again. None of the igniters worked, and I could hear arcing under the cooktop, indicating one or more of the igniter HV wires had somehow grounded. After a fruitless search for instructions on raising the cooktop, I stumbled upon an envelope glued to the back of the range that told me to remove all four burners and igniters and to release the cooktop by inserting a thin screwdriver under the front edge about 3" from each end to release the spring clips. Several of the igniters were cemented in place with caramelized sugar and required some pretty vigorous prying to dislodge. If I had this to do again on a range that had been ridden hard, I wouldproactively order a full set of gaskets (they're fragile), the HV harness (even if it doesn't leak as mine did, the igniter connectors degrade from heat exposure), a set of electrode mounting clips (none of them were much use either), and enough igniters to replace any that don't work plus at least one. I pried out the recalcitrant igniters; in retrospect I should have crushed them because of the severe risk imposed by prying of breaking either a burner casting or the cooktop -- either of which are far more expensive than another igniter.
Was this helpful?
Thank you for voting!
Convection oven fan and door light not working
18 of 22 people found this instruction helpful.
  • Michael from Albuquerque, NM
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
The first step was to determine whether the problem was with the fan itself or the switch. I did this by opening the back cover and using a Volt meter to verify that the fan was not getting power. (I could have skipped this step.)

Next, I unplugged the range, closed up the back cover and lifted the range hood by removing two he x head screws that are just inside and on either side of the top of the opening in the range door. Propping the hood open, I removed the connector leading to the switch, then pushed the switch out the front. Inspection showed that the switch was damaged so I closed up the range and ordered the part from Part Select. Once the part arrived, it was a 15 minute job to unplug the range, lift the top, install the new switch, and close up the unit.

Caution. On starting to install the switch, I failed to unplug the range and my finger brushed one of the hot contacts leading to the switch. Thankfully, I was not injured. Do not repeat my mistake on this issue. Unplug the range even if you're only installing this simple switch.
Was this helpful?
Thank you for voting!
Replacing Spark Igniter
13 of 17 people found this instruction helpful.
  • RICHARD from HERNDON, VA
  • Really Easy
  • Less than 15 mins
  • Pliers
Pulled the old one out. Disconnected the wire. Repaired the frayed wire cover with Liquid Tape. Connected the wire. Inserted the new part into the hole. This is after installing a new spark module earlier. But that was dumb easy too. So for about $100 bucks in parts and an hour of my time I saved myself the appliance repairman money and agonizing scheduling and dealing with them for the price of gold. I also replaced all the gaskets on the burners in that time. It so easy even a financial planner could do it.
Was this helpful?
Thank you for voting!
Interior light needed replaced
22 of 46 people found this instruction helpful.
  • Leo from TWIN FALLS, ID
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.
Was this helpful?
Thank you for voting!
Twice I ordered the oven light bulb & each time the light bulb was defected
18 of 38 people found this instruction helpful.
  • Barbara from BELLEVUE, WA
  • Very Difficult
  • Less than 15 mins
I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appl iance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance
Was this helpful?
Thank you for voting!
One burner would not light without using a match
10 of 15 people found this instruction helpful.
  • Robert from Stafford, VA
  • Really Easy
  • Less than 15 mins
I removed the burner head #152 and the Burner Cap #330, no tools are needed to remove these items. I pulled the igniter up far enough to get to the wire, disconnected and connected the new igniter put it back in place, reassembled the two parts plugged it back in and turned it on and it worked.
Was this helpful?
Thank you for voting!
Replace Oven light socket and light bulb in kitchen Range
6 of 6 people found this instruction helpful.
  • Ronald from TUCSON, AZ
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set, Wrench set
1) Turn off power at circuit breaker panel
2) Slide out Range from wall
3) Unplug Range
4) Remove back panel and unplug electrical connections to socket
5) From front of oven, remove glass cover over old oven light bulb and remove flange that holds socket and bulb
6) Remove old socket from mounting flange and disc ard.
7) Place new socket into mounting flange
8) Screw mounting flange and new socket into the oven from front. Reattach electrical connections from back.
9) Screw in new light bulb from front
10) Replace existing glass cover over new light bulb and snap wire holder in place
11) Replace back panel
11) Plug in range
12) Slide range back to original position
13) Turn on power
Works like a charm! Thanks for having the parts after 30 years!
Was this helpful?
Thank you for voting!
Burnt Smell
8 of 17 people found this instruction helpful.
  • Eugene from Hilton Head, SC
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Unplugged the Range and removed the two screws holding down the cook top. You do not need to remove the vent chamber at the rear of the range since the top lifts up about 4 inches. This should be enough room to get your hand onto the plug going to the door switch. Pull off the plug and remove the swich. Pop in the new one, put on the plug, reinstall the two screws and you are done!

Read the thread on "burnt smell" and DO NOT assume it is a burned out element. Follow your nose!!
Was this helpful?
Thank you for voting!
Oven meat probe broken
3 of 3 people found this instruction helpful.
  • robert from FAIRFIELD, OH
  • Very Easy
  • Less than 15 mins
This item worked as described. I paid more for this 'oem' probe than the generic 1 because i didn't want to chance it not working as others have reported.
- works great. tested it....snaps in, reads correctly, snaps out.
Was this helpful?
Thank you for voting!
cooking top flame shoot out to high.
5 of 9 people found this instruction helpful.
  • veth from san pedro, CA
  • Really Easy
  • Less than 15 mins
  • Nutdriver
First i remove the two torx screws that hold the base burner and the head burner out and then reinstalled with new one that i purchase online from partselect.
Was this helpful?
Thank you for voting!
Oven will not preheat. Pulses on an off.
7 of 15 people found this instruction helpful.
  • Paul from San Francisco, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Turned off the gas. Disconnected gas inlet, burner supply line and oven supply line from regulator. Unscrewed regulator from its bracket. Replaced with new regulator in reverse order and added teflon tape suitable for gas lines to all threads.

Unfortunately, the regulator was not the cause of the problem and the oven still do es not prehead - acts exactly the same.
Was this helpful?
Thank you for voting!
burner would not light because spark was skiping to ground elsewhere
3 of 4 people found this instruction helpful.
  • David A from Spring, TX
  • Really Easy
  • Less than 15 mins
  • Nutdriver
First I removed two screws holding head in place and carefully lifted assembly up using flat screwdriver. I separated old igniter from feed wire with gentle pull. I reversed assembly after cleaning old gasket residue. torque screws back in place after cleaning with small ss wire brsh in dremel tool. Tighten in steps to firm light touch. I used new gashket and ignitor.
Was this helpful?
Thank you for voting!
lights blown out
6 of 14 people found this instruction helpful.
  • Gerald from WINTERVILLE, GA
  • Very Easy
  • Less than 15 mins
replaced lights in refrigirator and freezer
Was this helpful?
Thank you for voting!
Replacing ignitor
2 of 2 people found this instruction helpful.
  • Sam from Austin, TX
  • Easy
  • Less than 15 mins
Got ignitor and it did not have wire attached as shown in the picture of parts. However, all I did was take burner cap off, and gently life ignitor up and out, detach the wire, attach new ignitor to wire and reset.
Was this helpful?
Thank you for voting!
All Instructions for the JGB920SEC2SS
1 - 15 of 34