EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

JDP46BD1BB General Electric Range - Instructions

All Instructions for the JDP46BD1BB
76 - 90 of 113

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Small element in center burned into(inoperative
1 person found this instruction helpful.
  • Douglas from Gravette, AR
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
1.Move range in position to access electrical wall disconnect and unplug. 2.Remove two 5/16 screws (located under top fwd. edge of cook top, Lift entire top assy up from front and prop with appropriate device(short 2x4 about18 inches long works well) 3.Remove two small phillips screws securing two metallic keeper devices holding burner a ssy in place. This should allow burner assy to be removed.4.Disconnect electrical spade connectors from ceramic terminal blocks on old burner assy.CAUTION: [SPADE CONNECTORS FIT TIGHTLY DO NOT PULL ON WIRES USE PRYING FORCE WITH FLAT SCREWDRIVER DIRECTLY ON TERMINAL].Remove connectors one at a time re-connecting to same location on new assy. Reassemble in reverse order.
Was this helpful?
Thank you for voting!
only the inner/smaller part of the dual burner is working
2 of 5 people found this instruction helpful.
  • Albert from South Boston, VA
  • Really Easy
  • Less than 15 mins
I ordered a new burner assuming As is turns out: nothing wrong with the burner.
Was this helpful?
Thank you for voting!
small (inner) burner was not 'burning'
1 of 2 people found this instruction helpful.
  • Jerry from Tierra Verde, FL
  • Easy
  • Less than 15 mins
  • Pliers, Screw drivers
turn off the power at the breaker first

remove the 2 screws under the 'lip' of the stove top (open the oven door to get to them)

prop up the stove top on the cardboard box the part came in

pull off the wires one by one and attach to the new burner OR record where each wire goes first

remove the old burner (2 screws) and attach the new burner

screw down the stove top

try the burner - when it does not work flip the power breaker back on and then try again

bask in the joy, admiration and wonder directed your way by various family members
Was this helpful?
Thank you for voting!
cooktop inner ring did not work
1 of 3 people found this instruction helpful.
  • Matthew from Lexington Park, MD
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Dear PartSelect:

I am very impressed by your service and company. My order arrived in less than 24 hours. It was a perfect match and is currently in service. I am very satisfied with the entire experience and will use your company again.

I simply opened up the cooktop with a screwdriver and disconnected the wire s to the affected burner. After the part arrived, I reconnected them. I had to swap over two brackets from the old burner, so don't throw it away until the new one arrives. It went back together very easily and worked immediately.

Matt Brennan
Was this helpful?
Thank you for voting!
Two stage burner was not working on the outer part of burner.
0 of 1 people found this instruction helpful.
  • Gregory from Pleasant Valley, MO
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Locate breaker box and turn off breaker to stove. Removed the two screw in front that hold the top in place. Raised the top and supported it with the box the new burner came in. Removed two screws that held the burner in place and the 5 wires one at a time an installed them on the new burner. Put new burner in place and installed two mounting screws. Reinstalled the two screws in the front to hold the top in place then turned the breaker back on and tested burner. Worked great. Received part in 2 days.
Was this helpful?
Thank you for voting!
Bad Burner
  • Roosevelt from Waggaman, LA
  • Really Easy
  • 15 - 30 mins
I simply removed the 2 anchor screws in front of the stove and wrote down the wiring order on the instillation diagram, removed the old burner, removed the two studs, made sure they were installed on the right numbers place them in the new burner, wired the new burner, placed the springs respectively. Placed them in the correct holes in the frame to be sure that the burner was aligned properly. Put the washers on the studs and replaced the frame screws, lowered the cook top and returned the screws to lock the cook top in place.
Was this helpful?
Thank you for voting!
Small burner not working, outside was fine
  • Lynda from Burdock, SD
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Followed directions that I found on the internet and it was easy to remove the old burner and replace it with the one I ordered from you. There was no problems at all.
Was this helpful?
Thank you for voting!
large burner on the dual element not working
  • Alan from Medina, OH
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers
The part arrived much sooner than I anticipated. The job was a little harder and took a little longer for me because I'm not good at repairing things. I usually have to call someone. However, I followed the step by step instructions that were provided both on the website and with the mailed item and had no problems. The instructions w ere clear and easy to follow. The tools needed were very basic - all of which I had on hand. If I could do it - anyone can.
Was this helpful?
Thank you for voting!
8 inch burner was burnt out
  • Luis from Kissimmee, FL
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
replacement was easy. pulled away the stove from wall. unplug the stove. open oven door. remove the two hex head screws holdings stove top. raise the stove top in the front. supported stove top with a 16 inch piece of wood. place New Burner under old burner. remove old burner remove wires remove old burner and place it on top of new burn er connected the wires from burner to new burner. install new burner. remove support lowered top down. plugged in stove tested. .burner. burner w.ork fine. reinstall hex head screws back top. pushback stove back into the wall. testes over again. all the stove work done.
Was this helpful?
Thank you for voting!
A large burner (haliant Burner 8" ) went out on my Hotpoint Electric Range
  • Ruth from Potosi, MO
  • Easy
  • 15 - 30 mins
  • Screw drivers, Wrench set
I ordered the part on a Monday and Tuesday afternoon I received it! I went a route I often take first. I read the instructions of others before starting my job and opened the top of the range. There are two screws under the range top in front near the oven door, one on either side, that must be removed. After this I opened the top of the range and positioned a piece of 2X2 about 20 inches long at an angle to hold the top up while I worked on the burner. I then used my phone to take a close up picture of the old burner while in place in my range so I could refer to it when putting the new one in place. I then took a pair of needle nose pliers and pulled off the wiring, then removed lock washers under the burner and removed the old burner, being careful not to lose the washers and springs. I took the new burner and layed it along side the old one to see exactly how it would be placed under the glass cover. I replace the springs and lock washers then referred to my photo and replace all the wires to the burner as they had been. Then lowered the top in place and put the screws back in place. That was it. I'm a 67 year old female, if I can do this, anyone can!
Was this helpful?
Thank you for voting!
Old dishwasher rack and silverware rack
  • Anne Marie from Andover, MA
  • Really Easy
  • Less than 15 mins
The whole process was very easy! I just got the model number and bought a new rack and silverware holder on,one. There was no assembly needed so I just popped them in and replaced the old ones! Very easy to do!
Was this helpful?
Thank you for voting!
Open door. Put racks in.
  • Harriet from Jacksonville Beach, FL
  • Really Easy
  • Less than 15 mins
nothing to it.
Was this helpful?
Thank you for voting!
Gasket worn and needed to be replaced
  • Thomas from Loveland, OH
  • Really Easy
  • Less than 15 mins
I simply removed the old one and installed then new one. No special tools needed.
Was this helpful?
Thank you for voting!
I needed an oven with three racks, mine came with two.
  • BETTY from CYPRESS, TX
  • Easy
  • Less than 15 mins
just slipped it in
Was this helpful?
Thank you for voting!
Replaced damaged oven rack
  • Vicki from Irvine, CA
  • Really Easy
  • Less than 15 mins
I ordered the oven rack on a Tuesday and received it the very next day - was wowed at the service.
Was this helpful?
Thank you for voting!
All Instructions for the JDP46BD1BB
76 - 90 of 113