EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

JDP36BW4WH General Electric Range - Instructions

All Instructions for the JDP36BW4WH
91 - 105 of 339

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
element broke
1 person found this instruction helpful.
  • Richard from NEW BERLIN, NY
  • Really Easy
  • Less than 15 mins
  • Nutdriver
took 2 screws out that held element in, pulled old element out of oven wall, unhooked the wires. Hooked the wires to the new element, pushed it back into the oven wall, replaced the 2 screws.
Was this helpful?
Thank you for voting!
Surface burner switch malfunction allowing the burner to remain on high heat after turning to low heat.
1 person found this instruction helpful.
  • John from OAKLAND, MD
  • Easy
  • 15 - 30 mins
  • Screw drivers
I removed two small screws located on the underside of the control panel. I then rotated the bottom of the control panel up and dislodged the few connections at top back of control panel. The control panel became loose enough to lay forward exposing the inner control switches. The old problem switch wiring was removed one by one and place d in the same spot on the new switch. The old switch was then removed by pulling off the front control knob and then unscrewing two screws holding the old switch in place. Then the new switch was installed exactly as the old switch was removed.
Was this helpful?
Thank you for voting!
Old Terminal Block was arcing.
1 person found this instruction helpful.
  • Robert from HOUSTON, TX
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Cut Wires to old terminal block and wired in new Terminal Block
Was this helpful?
Thank you for voting!
element broke
1 person found this instruction helpful.
  • Art from FRESNO, CA
  • Very Easy
  • 15 - 30 mins
  • Screw drivers
Fast shipping, Very easy to install I am a senior and had no problems works Great!!
Was this helpful?
Thank you for voting!
Uns rewed and pulled out
1 person found this instruction helpful.
  • Kathy from madison, WI
  • Really Easy
  • 15 - 30 mins
  • Wrench set
At first thought I was taking out some insulation but. "Clamp" just slid off and was very easy to install! Finding the right size socket took longer than the repair!
Was this helpful?
Thank you for voting!
Broken plastic handle end caps
1 of 2 people found this instruction helpful.
  • Joseph from PITTSBURGH, PA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Step #1: Remove 2 screws at the inside top of the oven door that holds the inner/outer oven door together. Step #2: Remove the screws from the inner door that hold the plastic handle end caps to the door. Tip: Use a file to dress up the tips of the metal handle bar so that it fits easily into the new plastic handle end caps. Step #3 : Install the first new plastic handle end cap. Step #4: Slide the metal handle bar into the plastic handle end cap that was just installed on the outer oven door. Step #5: Place the other plastic handle end cap on the metal handle bar. Step #6: Install the second plastic handle end cap on the outer oven door. Step #7: Reassemble the oven door by installing the screws that were removed in step #1.
Was this helpful?
Thank you for voting!
burned out
1 of 2 people found this instruction helpful.
  • David from Woodbridge, VA
  • Really Easy
  • Less than 15 mins
  • Nutdriver
My dealer was unable to find the part even with a model number. Your accurate drawings allowed me to select correct part. It was a perfect replacement in every way and cheaper (by $10) than the dealer. Also quicker.
Was this helpful?
Thank you for voting!
Oven wouldn't heat bottom
1 of 2 people found this instruction helpful.
  • Thomas N from Blackfoot, ID
  • Really Easy
  • Less than 15 mins
  • Nutdriver
.First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and reversed the procedure with the new element very simple.
Was this helpful?
Thank you for voting!
Bake element broken
1 of 2 people found this instruction helpful.
  • Charles from Damascus, MD
  • Easy
  • Less than 15 mins
  • Wrench (Adjustable)
Before ordering, I took the element out to make sure I could do it. A flashlight was helpful.

I flipped off the circuit breakers to the stove, removed the racks and lifted off the oven door. Not having a nutdriver or socket set, I used a 6' crescent wrench to remove the two screws which hold the element to the back of the oven . I carefully pulled the element out until the spade connectors to the wires were exposed. I wiggled the connectors apart. I had pliers handy, but didn't need them.

I connected the new element to the wires and gently pushed the two connected prongs through their holes, trying not to disturb the insulation. I put a little WD-40 on the screws so they would go in easier. After tightening the screws with the crescent wrench, I replaced the racks and door. I flipped the circuit breaker back on and reset the clock. It works as good or better than new.
Was this helpful?
Thank you for voting!
Baking element burned through.
1 of 2 people found this instruction helpful.
  • James from Seattle, WA
  • Easy
  • Less than 15 mins
  • Nutdriver
First I removed the two screws that hold the element in place, I then pulled the element out about three inches, and it shorted out on the main panel of the back of the range. I then went to the breaker box and flipped the switch so I could tell my wife "Yes, I had turned the power off."

Disconnecting the two wires and recon necting them was a simple operation after I cleaned my pants from the electrical short.

Re attaching the two-screw panes to hold the element in place finished the project.
Was this helpful?
Thank you for voting!
Double Oven door handles were off because of broken end pieces
1 of 2 people found this instruction helpful.
  • David H. from Arkadelphia, AR
  • Easy
  • Less than 15 mins
  • Screw drivers
Unscrewed three screws from each oven door. Unbolted the end pieces and replaced with new ones. Reinstalled oven door screws. Nothing to it.
Was this helpful?
Thank you for voting!
Lower bake element burned out.
1 of 2 people found this instruction helpful.
  • Elaine from Hanover, PA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
1. Turned off power at the breaker box. Removed oven door from oven, and removed bake racks. Determined replacement element from PartSelect was correct. Inspected new element. Using meter, determined new element was OK via continuity test. Gathered all appropriate tools to do the job.
2. Using 1/4" nut driver, removed two reta ining screws at back of oven that secure element
3. Pulled bad element out a few inches from oven back to reveal wires and spade connectors
4. Using screwdriver, pushed off electrical connectors from bad element and removed element
5. Inspected wires and connectors and determined them to be OK
6. Installed new element in reverse of above. Inspected oven controls and determined them to be OK. Turned on the breaker. Tested oven.
7. Baked a delicious chocolate cake
Was this helpful?
Thank you for voting!
heating element shorting out-sparking
1 of 2 people found this instruction helpful.
  • K from PERRYVILLE, MO
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
I turned off electric to the stove. In the oven, I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. After unpacking the new element, I placed it in the bottom of the oven, reconnected the two wires, and gently fed the wires back into the back of the oven. I then secured the new unit to the oven wall with the two screws.
Was this helpful?
Thank you for voting!
Just follow the enclosed instructions
1 of 2 people found this instruction helpful.
  • HAROLD from Tucson, AZ
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
Followed the instructions
Was this helpful?
Thank you for voting!
Bad sensor
1 of 2 people found this instruction helpful.
  • John from CASPER, WY
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
By myself
Was this helpful?
Thank you for voting!
All Instructions for the JDP36BW4WH
91 - 105 of 339