- Home
- JDP36BW4WH
- Instructions
JDP36BW4WH General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
broke
2 of 2 people
found this instruction helpful.
-
Barbara from Winston Salem, NC
- Really Easy
- 15 - 30 mins
-
Screw drivers
just replace the end cap with a new one all that was involue was to screw the new one in took about ten minutes and job done better than buying a new stove when the stove is still just like new. thank you for your on line help.
Was this helpful?
Thank you for voting!
Handle broke
2 of 2 people
found this instruction helpful.
-
Dean from Harrisonburg, VA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Took off the inside ( this allowed me to clean the glass) panel. Removed the two end parts with a screw driver. Replace the parts and we were good to go.
Was this helpful?
Thank you for voting!
Broken end cap
2 of 2 people
found this instruction helpful.
-
Jan from todd, NC
- Easy
- 15 - 30 mins
-
Screw drivers
The end cap was completly broke off to replace just fit cap ove end and screwed into place.
Was this helpful?
Thank you for voting!
broken light cover
2 of 2 people
found this instruction helpful.
-
Francis from LAKE ELSINORE, CA
- Very Easy
- Less than 15 mins
twisted it in place
Was this helpful?
Thank you for voting!
Burner control was erratic. Sometimes it worked, sometimes it didn't.
2 of 3 people
found this instruction helpful.
-
Charles from Clarksville, OH
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
First pull knob off switch. You may need a small screwdriver to gently start it. I then removed two screws, one in each end of control panel. Then rolled the panel up and out, as it is kind of hinged in the back. Removed two screws from switch front,layed it to the side and installed new switch. Removed wires (there were 5) one at a time
... Read more
with needle nose pliers, and placed on new switch. Replaced panel screws and was finished. Easy fix, quick delivery of part, I have used Partselect in the past and will continue.
Read less
Was this helpful?
Thank you for voting!
children used it for a chin bar and broke the handle and the piece that holds the handle on
2 of 3 people
found this instruction helpful.
-
Joyce from Houston, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
We had to buy washers and screws to hold the handle on.
Then all we did was undo the screws that were on the side of the door. place handle on door screw the new screws and washers that we had to buy and replace the side screws and it was fixed.
The only problem that I found was that the handle kit did not come with scre ... Read more ws or some kind of attachment to hold the handle on the door. We had to buy extras at the hardware store for that.
Then all we did was undo the screws that were on the side of the door. place handle on door screw the new screws and washers that we had to buy and replace the side screws and it was fixed.
The only problem that I found was that the handle kit did not come with scre ... Read more ws or some kind of attachment to hold the handle on the door. We had to buy extras at the hardware store for that.
Read less
Was this helpful?
Thank you for voting!
Oven door glass broke
2 of 3 people
found this instruction helpful.
-
BEVERLY from PHENIX CITY, AL
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
First, I cleaned all the glass from the stove. then I inserted the replacement glass into the slots and screwed the bolts back into the stove. It took me about 1o minutes to do repair. It waS VERY EASY..
Was this helpful?
Thank you for voting!
oven stopped heating and element appeared broken
2 of 3 people
found this instruction helpful.
-
Henry J from South Haven, MI
- Really Easy
- 15 - 30 mins
-
Socket set
The customer service rep was brilliant in finding the
right part number! It was sent the following day
(with email to let me know) The part itself was just
exactly like the old one. I simply turned off the power,
removed the 2 metal screws and unplugged the
broken element. The new one fit properly and works
... Read more />like a million dollars. For about $50, you made me
look like a hero in my own house! Thjank you
right part number! It was sent the following day
(with email to let me know) The part itself was just
exactly like the old one. I simply turned off the power,
removed the 2 metal screws and unplugged the
broken element. The new one fit properly and works
... Read more />like a million dollars. For about $50, you made me
look like a hero in my own house! Thjank you
Read less
Was this helpful?
Thank you for voting!
bake element burnt into
2 of 3 people
found this instruction helpful.
-
gary from assumption, IL
- Easy
- 15 - 30 mins
-
Nutdriver
repair went fine, real easy.
Was this helpful?
Thank you for voting!
Intermittent heat then no heat on oven element
2 of 3 people
found this instruction helpful.
-
Bruce from AKRON, PA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
With multimeter checked resistance of oven sensor. Specs called for 1100 ohms. It was off by 27 ohms. The sensor from Part Select had exact wire connection as original. Then just matter of undoing old and reconnecting with new one.
One unsatisfactory event. I asked Part Select why my clock did not work or light up(timer ... Read more works ok) . Answer was: sorry we have no time to help you. That soured the otherwise happy experience.
One unsatisfactory event. I asked Part Select why my clock did not work or light up(timer ... Read more works ok) . Answer was: sorry we have no time to help you. That soured the otherwise happy experience.
Read less
Was this helpful?
Thank you for voting!
The phillament ends were pointed straight and the one I removed from the oven were bent in an angle .
1 person
found this instruction helpful.
-
Michael from CLAY, NY
- A Bit Difficult
- 30 - 60 mins
-
Pliers
Bent the tips so the phillament can fit inside the oven.
Was this helpful?
Thank you for voting!
Lower Oven Door End Knobs Cracked And Split
1 person
found this instruction helpful.
-
JOHN from CLIFTON, VA
- Really Easy
- 30 - 60 mins
-
Screw drivers
Open door lift door off hinges lay door face down on flat surface remove 6 phillip head screws 3 on each side lift housing out of door case remove end knob phillip head screws installed one knob insert bar attch second knob and tighten screws lay housing back into casing attach screws doing one at a time on each side slide door back on t
... Read more
o hinges and test operate, you are done!
Read less
Was this helpful?
Thank you for voting!
No heat lower bake unit / Broiler unit heats ok
1 person
found this instruction helpful.
-
Richard L. from Clear Spring, MD
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers
Safety first: Turn range circuit breaker to off position. Turn a surface unit [burner] to the on position ,if no light exists power has been removed. Turn surface unit to off position. To remove bake unit. With a 1/4 socket driver remove two self tapping screws and gently pull out on the bake unit until you can access the slide on
... Read more
terninals. Careful lenth of wire is limited. Remove slide on terminals two each [2] . Install new bake unit in reverse order . Restore power
Read less
Was this helpful?
Thank you for voting!
Complete failure of oven controls, no error codes
4 of 10 people
found this instruction helpful.
-
Brian from Mariposa, CA
- Easy
- 30 - 60 mins
-
Screw drivers
Was very difficult to be certain of the right controller due to the exact model number of the range did not exist. Somewhat of an expensive part to make a guess.
After contacting no less than 5 parts dealers, Part Select was the only company that could immediately identify the correct number, (the model # on the range had an extra ze ... Read more ro in the middle).
Was able to purchase the part confident it was correct, at a good price, with fast shipping.
Thanks
After contacting no less than 5 parts dealers, Part Select was the only company that could immediately identify the correct number, (the model # on the range had an extra ze ... Read more ro in the middle).
Was able to purchase the part confident it was correct, at a good price, with fast shipping.
Thanks
Read less
Was this helpful?
Thank you for voting!
oven coil caught on fire and broke in half!
2 of 4 people
found this instruction helpful.
-
Cynthia from Houston, TX
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Wrench (Adjustable)
I turned off the main power! Then unscrewed the back cover unhooked the wires and unscrewed the coil inside of the oven and pulled it out. My 10yr old son and I measured it and went online to order the part. I first did go into BestBuy and they didn't have the part (But they tried to sale me a new oven!) LOL Now who said a newly divorc
... Read more
ed mom couldn't fix her own oven! My Tech Support skills came in handy! Women Rock! LOL
Read less
Was this helpful?
Thank you for voting!