JD968SF3SS General Electric Range - Instructions

Remove the top back panel to expose the switch. Remove the switch knob & mounting bezel and then unscrew the 2 mounting screws from the front. Replace the wires one by one and follow the enclosed directions in the event that this is an upgrade for an older switch. Remount the switch from the front and replace the back panel.

This went pretty smoothly. Watch the video and just follow along step-by-step and it goes well. It would have only taken about 30-45 minutes (even being careful and slow) but I ended up placing the glass twice (be very careful and triple check that all the insulation gets poked under the housing and none is sticking out). The first time I ... Read more had a small piece sticking out. (Use gloves for this part so your hands don't itch). The second time I needed to redo part of it is I forgot one of the spacers on the door handle and had to get that in there so the handle worked properly. I also took the time to clean the oven while the door was off so that took some time. Total I probably had 1.5-2 hours into this project but at least half of that was me cleaning and being fussy. This is an easy repair. I'm not a confident repair person and this wasn't difficult. It was a little time consuming but well worth the cost vs calling a repair person or buying a new appliance. You do need to have a specialty star head on a screwdriver but my simple tool kit had all the tools I needed. The oven has been working great since the repair.

Removed old switch, put metal jumper from old switch to new one and connected wires to the new one . Reinstalled. Works great.

Turn the glass enclosure counterclockwise to expose bulb.Turn the power off at circuit breaker panel.Handle the bulb carefully with paper towel covering the bulb.Push the bulb in socket.replace glass enclosure,turn power back on.

turn off the power at the breaker first

remove the 2 screws under the 'lip' of the stove top (open the oven door to get to them)

prop up the stove top on the cardboard box the part came in

pull off the wires one by one and attach to the new burner OR record where each wire goes first

remove the ... Read more old burner (2 screws) and attach the new burner

screw down the stove top

try the burner - when it does not work flip the power breaker back on and then try again

bask in the joy, admiration and wonder directed your way by various family members

I ordered a new burner assuming As is turns out: nothing wrong with the burner.

Dear PartSelect:

I am very impressed by your service and company. My order arrived in less than 24 hours. It was a perfect match and is currently in service. I am very satisfied with the entire experience and will use your company again.

I simply opened up the cooktop with a screwdriver and disconnected the wire ... Read more s to the affected burner. After the part arrived, I reconnected them. I had to swap over two brackets from the old burner, so don't throw it away until the new one arrives. It went back together very easily and worked immediately.

Matt Brennan

Locate breaker box and turn off breaker to stove. Removed the two screw in front that hold the top in place. Raised the top and supported it with the box the new burner came in. Removed two screws that held the burner in place and the 5 wires one at a time an installed them on the new burner. Put new burner in place and installed two ... Read more mounting screws. Reinstalled the two screws in the front to hold the top in place then turned the breaker back on and tested burner. Worked great. Received part in 2 days.

I got someone to look at the stove. They told me what I needed. I looked all over the Internet and couldn't find the part. One guy told me just to buy a new stove top because mine was an antique. It still looked good and two burners were still working. I didn't give up. I found the part on partselect bsite and was thrilled. It ship ... Read more ped fast and was exactly the right part. Now my stove works like new.

Replaced it

First of all, the sensor had the proper ohm reading...at ambient temperatures. I suspected the sensor because it would jump in large degree increments over 200°F. From what I read online, the only other part that would cause this was a faulty circuit board. I opted to try the $20 part first vs. the $200 part. It worked. One screw on the b ... Read more ack top of the inside is all that holds the sensor in. Pull the wires out and you will find a quick-disconnect. New part had the same connector (thank you). Thread the wires back through the hole and replace the screw. Works like a champion (verified with an independent thermometer. That is all she wrote. I only wish I purchased two, since they don't last that long... 4 years...or so. I just bought the house built in 2007 and empty for a year... and it took 45 minutes to cook a pizza, and even then the bottom dough was light. A house without an oven is like a hot dog without mustard!

Turned off the power at the breaker. Then I lifted the cooktop by pressing up from the bottom, while my wife slid two boards over the recess. I lowered the cooktop onto the boards, removed 12 screws around the perimeter of the case and carefully lifted the glass top and placed it on a towel on the DR table. (remove the control knobs first ... Read more ) removed the wires leading to the infinite control, marking which color when where, removed the two screws holding the infinite control, and replaced the old with the new. Reattached the wires, replaced the cooktop, replaced the screws, held it up while my wife removed the boards and then carefully lowered the cooktop into the recess. Attached the knobs, flipped the breaker back on and turned control to hi. It worked!

I unplugged the defective plug and replaced it with the new one. Took 5 min total

Ordered new probe

plug in thermistor when needed