EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

JD968KK4CC General Electric Range - Instructions

All Instructions for the JD968KK4CC
16 - 30 of 93

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Broiler Element Failed
6 of 8 people found this instruction helpful.
  • Ron from Irvine, CA
  • Really Easy
  • 15 - 30 mins
  • Socket set
Disconnect the power to the oven at the main breaker panel. Open the oven door to the first stop (not all the way open) and pull straight up to remove the oven door from the hinge. Using a 1/4" drive ratchet with 1/2" extension with 1/4" socket, remove the 1/4" sheetmetal screw holding the temperature probe at the center of the broiler mo unting plate. Remove the two 1/4" screws holding the broiler mounting plate. Remove the two 1/4" screws holding the broiler element at the ceiling of the oven. Pull the broiler element out from the back of the oven and there should be two electrical connectors at the back of the broiler element. Pull the electrical connectors off of element. Replace the element and re-install in reverse order.
Was this helpful?
Thank you for voting!
Wife broke the interior window by splashing water on it while heated to 450.
6 of 8 people found this instruction helpful.
  • Dennis from GRETNA, NE
  • Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Well I did it all wrong from the get go. I did finally do a search on how to replace it and then it was quite easy. Learn from me, watch video and save yourself tons of hassle.
Was this helpful?
Thank you for voting!
the temp was not accurate
7 of 12 people found this instruction helpful.
  • scott from new harmony, UT
  • A Bit Difficult
  • 15 - 30 mins
  • Socket set
had to remove the oven from the wall. once i realized that i had to take the side wall brackets off before removing the oven it was quite easy. then just had to remove oven door and slide the unit onto a chair while replacing the sensor. put it all back in and the wife was so happy to have her oven back she made me a batch of brownies. yu m.
Was this helpful?
Thank you for voting!
replaced gasket on oven door
5 of 6 people found this instruction helpful.
  • mary from MODESTO, CA
  • Easy
  • 15 - 30 mins
followed video exactly
Was this helpful?
Thank you for voting!
Stovetop radiant burner went out
6 of 10 people found this instruction helpful.
  • Frank from Marietta, GA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Turned off power at circuit breaker. Disconnected electrical connections from stove and lifted stove top out of counter. Removed glass top by removing about 8 screws from side of stove top.Replaced burner element and replaced glass top.
Was this helpful?
Thank you for voting!
bulb burnt out
5 of 7 people found this instruction helpful.
  • Christie from NAPERVILLE, IL
  • Very Easy
  • Less than 15 mins
turned off power to oven; pulled out old bulb (unscrewed glass cover to access). Noted the direction of the electrical prongs when pulled bulb out... and inserted new bulb. Turned back on power to oven - bulb worked
Was this helpful?
Thank you for voting!
Burnt Broiler Element
5 of 7 people found this instruction helpful.
  • ROBERT P. from Santa Fe,, NM
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers, Socket set
Just like everyone else it was a simple r&r. However, when removing or installing wire clips I make it a habit to hold the ends with needle nose to prevent any: "snap!" ooops! However to prevent burning the element in the first place, it is strongly suggested to push that broil button twice so that it is set to low temp. It is too easy to use the high setting which will shorten the elements life by 40 - 60 %. Also, keep the oven door partially open when using the broiler. Like the manual tells you!!!
Was this helpful?
Thank you for voting!
Melted Plastic and use of water caused false bottom to be damaged badly
5 of 7 people found this instruction helpful.
  • Michael from Wildwood, MO
  • Really Easy
  • Less than 15 mins
Oven door must be removed briefly while old false bottom is slid out and replaced with new one. Oven door is easily replaced and oven is like new.
Was this helpful?
Thank you for voting!
Oven slow to heat.
6 of 10 people found this instruction helpful.
  • Scott from Burleson, TX
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Pliers, Screw drivers
First I removed the 4 screws that hold the element in place. I then pulled the element out about 3 inches. I removed the sensor and disconnected the connector.
Was this helpful?
Thank you for voting!
Broken inner window
5 of 7 people found this instruction helpful.
  • randy from LORETTO, TN
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Watched video
Was this helpful?
Thank you for voting!
oven not as hot as temp display said it was
4 of 4 people found this instruction helpful.
  • John from HOT SPRINGS, AR
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
pull out stove, unbolt old temp sensor inside stove with 1/4 nutdriver, go to back of stove and take off cover and unhook sensor and hook up new one, put all back together and slide stove back in place.
Was this helpful?
Thank you for voting!
Poor heat control of the power boil element also would not shut down correctly
4 of 5 people found this instruction helpful.
  • john from Woodstock, NY
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Remove and unplug the control panel. Remove four 1/4 in screws securing the metal panel to which the four rangetop controls are mounted. Unscrew the affected control, be careful to note the wiring layout on the control. Reassemble and test test out all functions.
Was this helpful?
Thank you for voting!
Oven light
4 of 5 people found this instruction helpful.
  • Letty from KERRVILLE, TX
  • Very Easy
  • Less than 15 mins
I'm well past ninety and my sweet daughter inserted the tiny prongs. I was delighted to find a place that had the bulbs. Thank goodness for the internet ! (I'm not too old for that)
Was this helpful?
Thank you for voting!
False Bottoms in both ovens had aluminum pans melted on them and couldn't be cleaned
3 of 3 people found this instruction helpful.
  • Raymond from MISSION VIEJO, CA
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Use screwdriver to pull down tab on both hinges. Good hind on door and as you lower to full open door will come off. Pull old bottom, insert new bottom and put door back in slots. Close and then reopen to first position and push tabs back up to lock position
Was this helpful?
Thank you for voting!
Control awitch was bad
3 of 3 people found this instruction helpful.
  • Gary from CLEARWATER, FL
  • Easy
  • Less than 15 mins
  • Nutdriver, Pliers, Screw drivers
Just note the wire colors and match them where they go on the new control, remove and replace 7 screws and a zip tie and I was done.
Was this helpful?
Thank you for voting!
All Instructions for the JD968KK4CC
16 - 30 of 93