JD12W2 General Electric Range - Instructions

The repair seemed very easy, even before I attempted it. When I recieved my part it was very obvoius that this was my problem part. The old element was worn out(21 yrs old). Having Thanksgiving around the corner, my wife was happy we had a fix to our not ready to replace oven. I was very pleased with your website picture matching choices ... Read more and the very fast shipping you offered.
Thank You RR from Massachusetts

Removed the panel screws that hold the bake element to the back of the stove. Then I disconnected the old element from the wires. Attached the new element using the provided screws. Reattached the old panel screws to hold the new bake element in place. Works great.

The new bake element doesn't have an item number on it, so I ... Read more kept the old element in a cabinet someplace in case I have to replace this one again some day. I've lost the model number for my very old GE wall oven, so without that item number I'll be in trouble.

Super easy, 1 2 3 steps and your done. Make sure to turn power off, remove two screws off of back plate. Remove two screws on wire connectors. Throw old element away and connect both wires to new element and screw back into place. Turn power back on and start cooking.

diagnosed repair by installing heating element from lower oven into upper oven, and it worked. Ordered proper replacement part and installed using tools above. No problem besides the tight space.

Purchased the element from Partselect online -delivery was great -installed the new element in less than 10 minutes - the stove is now 100% again

Great Service

First I turned the circuit breaker off, then I removed the two screws with a nut driver, that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires with a straight scewdriver.

Reversed the the above process to install new element.

Oven was 27 years old.

Repa ... Read more ired and operational in less than 15 min.

Opened Breaker box
Threw oven switch
Removed two screws on element plate
Pulled element out 3 inch and removed two screws holding wires.
Ordered element on Tue.
Received element on Thur.
Reconnected screws on wires and plate
Threw oven breaker
Baked a cake

I disconnected the 240 volt supply by removing the fuses from the fuse panel. Next I removed two screws that hold the element in place with a nutdriver. Then being careful not to short or ground the wires I pulled the element out 3 or 4 inches and turned the oven control to the on position and tested for voltage, line to line then each li ... Read more ne to ground to be sure the correct fuses were pulled. Turned the controls back to off. Next I disconnected the wires using the same nutdriver and removed the old element.
I placed the new element in the oven, attached the wires using a screwdriver backing it up with pliers to hold the connector on the element, then slid the element into position and installed the two screws in the back of the oven, then reinstalled the fuses.
Partselect shipped the order right away. I ordered Thursday evening and received the element Monday morning using standard shipping. I wasn't able to reference the oven by part number (it is a 40 year old GE oven) but their pictures and 1" grid made it convenient to pick the correct part.
In the past I bought the main control circuitboard for my Kenmore dishwasher, a door light switch for my refigerator, a turntable motor for my GE microwave vent hood, and an element for a Maytag oven. Every time I have ordered parts they were in stock as indicated and shipped right away and were the right part.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires

removed it, ordered it and it only took 15 minutes to replace it.

I unscrewed the two mounting bolts from the back of the oven (with the oven turned off) and then removed the two screws that connected the wire to the old element and then screwed them all in reverse order the same way I removed them.

Very quick deli ... Read more very, within 3 days.

I removed the two screws that hold the element to the back of the oven. Pulling the element out of the back, I removed the screws which connect the element to the electrical wiring. I placed the new element into position and reconnected the wiring. I made sure that the wiring and connectors were insulated with shrink wrap plastic, then pu ... Read more shed the new element into place. Connecting the two screws to the back of the oven completed the job. Toughest part, kneeling on my knees -- the part supplied fit like a glove and it works wonderfully well. Hint: measure the connectors to the wiring so that you order the correct length! (I didn't and had to reorder, but I am very happy with PartSelect.)

First of all the part came super fast with standard delivery. We threw the circuit switch to the oven. We used a nut driver to remove the nuts holding the element in place and then gently pulled it out of the hole so we could see the terminals. Using a screwdriver we loosened the screws that hold the terminals to the power lines. We put t ... Read more he old element aside and laid the new element on the floor of the oven. Using a screwdriver and the original screws we attached the terminals of the new element to the power lines. Using a screwdriver and the new screws provided we attached the bracket to the back of the oven. Turned on the power; used the oven. Works perfectly.

Same as you described

Repair went fine after I got the second element shipped to me. First element sent was DOA, so I called customer service and they credited my CC for part cost and shipping, then charged the new replacement to my account and mailed it out. Got it the next day. Repair was easy - turned off power to oven took out two screws holding elemen ... Read more t in place. Unbolted the two wires from element and installed new element. Oven element heated up cherry red and I am back to baking with an oven I thought was a gonner. Was impressed with customer service replacement process. It was fast and easy with no problems. Will buy again from PartSelect.com. Thanks

Use nut driver to take off shield. Pull out element to expose element and wire connections. Use nut driver to take off the 2 little screws. Remember what side is positive(red wire) and what side is negative(black wire). Put shield over the 2 wire and reconnect to element. Will need a standard screwdriver for the new screws. Slide wires in ... Read more to insulation and put back on shield.