JD1202 General Electric Range - Instructions

I was a little leary of using a website to order a part to fix my oven, but we got the part within a week. It was very easy to install and it works like a charm!

Following common sense, I removed the broken bake element by first removing two retaining screws and then disconnecting the element from the internal wires using a nut driver for both operations. The new element was installed in reverse order first using a screwdriver to attach the element to the internal wires (the new element had embedd ... Read more ed threaded openings and came with two new machine screws) and then using the nut driver to secure the element to the oven wall.

I unplugged the stove, unscrewed two nuts, pulled the two wires forwrd and disconnected them. Attached the wires to the new burner and it works fine!

First I turned off the breaker to the stove in the breaker box and then removed the two small screws that hold the element in place. I then carefully pulled the element out about 3 inches and using a 1/4 inch socket, I unscrewed the screws that held the wire on the bake element. There were two wires held in place with 2 small screws. ... Read more I made sure that when I unhooked the wires they did not pull back into the back wall of the stove. I then removed the old element and put the new one in its place, hooked the two wires back up, pushed it back in place and secured it to the back of the wall of the stove with the other two screws. I then turned the power back on and presto, it worked perfectly. Like new again.
Thanks for everything.

(e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)

Once I watched the video pertaining to the installation of the part, the job was very easy.

It was quite simple after the part arrived. I actually had forgotten what the connection was because one wire was yellow and one was red. After calling the number that I had to no avail. I went to the computer to ask how to install the part. Installed in little to no time. Feel like a Jill of all trades. Bring on the next problem.

Element was in two pieces so it was obviously dead. I disconnected the stove from the power, I undid the two screws at the back of the oven and gently pulled the element out. There was enough slack to reach and pull the connectors apart. Done. I ordered the part from "PartSelect" and it arrived the next day. Unfortunately I ordered the el ... Read more ement with "Screw" convectors as opposed to "push on" connectors. I bought a couple of connectors and cut off the original connectors from the wires in the oven and replaced them making absolutely sure they were well and truly tight. Two screws cam with the element from "PartsSelect (Thankfully). Connected the wires and screwed it back into place. Stood clear, plugged it in and turned it on to max. Worked just fine, Thanks

This is a forty five year old oven. It was only four screws and it was done. The new part works like a champ! This save me from buying a $800.00 replacement. I removed the two 1/4 screws holding the element to the back of the oven and then took the flat head screws loose from the terminals on the old element. I then put everything back as ... Read more it came out; took less than 5 minutes and the part arrived overnight! Thank you again!!

Simply removed the old one and replaced it with the new one. Part Select was the only company that was able to identify the part without the Model Number. The Model number was
worn off and unable to read. After going through several
on-line parts dealers, Part Select was the only company that could identify the part I needed. ... Read more The repair was simple and
short. My old stand by oven is in operation again.
Thanks, Laura

The repair was a bit difficult because the screws connecting the wires to the element were small threaded bolts and no slot for a screw driver. They were very difficult to break loose - that's when we used the Liquid Wrench and waited. Other than that, the repair went smoothly. It is better to remove the oven door, if you can, otherwis ... Read more e the rear of the oven is not as accessible. It is also a good time to change the light bulb.

First unplugged from wall outlet, then just removed the old element and four screws. Replaced with the new one and rescrewed in. VERY VERY EASY!

First I unplugged the oven from the wall. Then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. The installation process was just as easy as the removal. Approx 10 minutes and I was cooking. BTW, the heating element was at my house the next day after ... Read more ordering. Great service

First , for safety, I flipped breakers to kitchen applicances to cut off the power. Removed the 2 screws that held the old element in place. Pulled it out a couple of inches and disconnected the 2 wires attached to the prongs of the element. Reattached them to the new element, pushed it back in and replaced the screws. Turn power back ... Read more on and voila! ... was ready to bake again! All this is a matter of 15 mins!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, put the new one in and reversed the procedure. Also delivery was great, I ordered the part and received it the next morning. I highly recommend your service.