EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

JCSP47BF3BB General Electric Range - Instructions

All Instructions for the JCSP47BF3BB
46 - 60 of 174

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
the temp was not accurate
7 of 12 people found this instruction helpful.
  • scott from new harmony, UT
  • A Bit Difficult
  • 15 - 30 mins
  • Socket set
had to remove the oven from the wall. once i realized that i had to take the side wall brackets off before removing the oven it was quite easy. then just had to remove oven door and slide the unit onto a chair while replacing the sensor. put it all back in and the wife was so happy to have her oven back she made me a batch of brownies. yu m.
Was this helpful?
Thank you for voting!
Oven would intermittently loose all power when hot
5 of 6 people found this instruction helpful.
  • Eric from Hemphill, TX
  • Easy
  • 15 - 30 mins
  • Socket set
First found and threw appropriate breakers. Then removed knobs and faceplate retainer nuts and pulled off faceplate. Next removed four control panel retaining screws and lifted out and partially spun/inverted control panel. Couldn't fully remove due to wiring. Next removed four oven control screws and pulled back control module. Then just removed all wiring connections to old control module. Worked in reverse with new control module, turned breaker back on, and just had to set the clock. Back in business!
Was this helpful?
Thank you for voting!
wire connection to socket was bad
6 of 10 people found this instruction helpful.
  • David from Gansevoort, NY
  • A Bit Difficult
  • 15 - 30 mins
  • Pliers, Screw drivers
Disconnected the old socket ( 2 srews ) removed the two wires from the old socket, reconnected them to the new socket and reinstalled the lamp.
Was this helpful?
Thank you for voting!
oven not as hot as temp display said it was
4 of 4 people found this instruction helpful.
  • John from HOT SPRINGS, AR
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
pull out stove, unbolt old temp sensor inside stove with 1/4 nutdriver, go to back of stove and take off cover and unhook sensor and hook up new one, put all back together and slide stove back in place.
Was this helpful?
Thank you for voting!
Oven slow to heat.
6 of 10 people found this instruction helpful.
  • Scott from Burleson, TX
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Pliers, Screw drivers
First I removed the 4 screws that hold the element in place. I then pulled the element out about 3 inches. I removed the sensor and disconnected the connector.
Was this helpful?
Thank you for voting!
Burnt Broiler Element
5 of 7 people found this instruction helpful.
  • ROBERT P. from Santa Fe,, NM
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers, Socket set
Just like everyone else it was a simple r&r. However, when removing or installing wire clips I make it a habit to hold the ends with needle nose to prevent any: "snap!" ooops! However to prevent burning the element in the first place, it is strongly suggested to push that broil button twice so that it is set to low temp. It is too easy to use the high setting which will shorten the elements life by 40 - 60 %. Also, keep the oven door partially open when using the broiler. Like the manual tells you!!!
Was this helpful?
Thank you for voting!
One of the drawer supports broke off
5 of 7 people found this instruction helpful.
  • John from Sandy Hook, CT
  • Really Easy
  • Less than 15 mins
  • Nutdriver
I pulled out the drawer and inserted the new support. This one inserts into the back of the drawer as opposed to the sides. I had ordered two of the replacements even though I only needed one and decided to replace both. I think it was a good move as the drawer works better than when we first got it. Just one simple screw made it com plete.
Was this helpful?
Thank you for voting!
outside element burned out
4 of 4 people found this instruction helpful.
  • peter from westfield, MA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two plugs.
plugged in the new element and screwed it in place
Was this helpful?
Thank you for voting!
old blackened oven racks
8 of 17 people found this instruction helpful.
  • Roger from Falls Church, VA
  • Really Easy
  • Less than 15 mins
Replaced old with new.
Was this helpful?
Thank you for voting!
Burner element was burnt
4 of 5 people found this instruction helpful.
  • Chandra from Naugaeuck, CT
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Socket set
It was very easy. First turn off the power. Remove two screws to pick up the hood then remove two screws holding the element. Tag the wires with number. Unplug the old burner attach the wires to new burner. Attach two screws with spring to hold the burner, put the hood down and put the screws holding the top hood.
Was this helpful?
Thank you for voting!
Broker inner glass
4 of 5 people found this instruction helpful.
  • marc from PARK RIDGE, NJ
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Very easy to remove the parts and to reassemble
Was this helpful?
Thank you for voting!
Hole In Back Was Too Small
5 of 8 people found this instruction helpful.
  • Lloyd from Hemphill, TX
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers
I had to cut about 1/4 in. Off the top part of the back hold so the bakeing element would set on the bottom of the oven. Everything else went okay.
Was this helpful?
Thank you for voting!
The front right outer element was defective.
4 of 5 people found this instruction helpful.
  • Peter from Abbeville, LA
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
My cooktop is a stand alone unit mounted in a counter top not associated with an oven.
-Removed power to the cook top. Breaker off.
-Lifted the cook top straight up from the counter top and placed two 24 inch board strips to support it above the counter top. This was very easy by pushing up from the bottom of the cook top. T his is a two person job preferably.
-Removed the six phillip screws below the glass surface edge. 3 in the front, three in the back.
-Remove knobs and remove the glass top by lifting straight up.
-Record the wire positions on the element on paper and remove the connections.
-The element is mounted on two spring loaded studs that have spring clips as a retainer. Remove the two clips by pulling straight up with a plier or needlenose.
-The replacement element did not come equipped with the two mounting ears that the original had. I removed the two ears from the defective element and installed them on the new element. Very easy. Two phillips screws. The elements have perferations in the correct areas to accommodate this.
-Placed the new element in position and reinstalled the spring clips.
-Install the wiring terminals in the correct positions.
-Reinstalled the glass surface and the six phillips screws. Reinstall the knobs.
-Lower the cook top back into its counter top position.
-Return power to the cook top.
-Installation complete. Very simple!
Was this helpful?
Thank you for voting!
Small front burner on our glass top stove died.
3 of 3 people found this instruction helpful.
  • Robert from FLEMING ISLE, FL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Robert did not do the repairs. I did! 70 year old housewife. I watched a Utube video and thought I could certainly handle that. Ordered my part from your site. It came in two days. Burnet was replaced in under 20 minutes by me! Anyone can do this. Super easy, parts just plug in.
Was this helpful?
Thank you for voting!
The dual burnner had somthing drop on it and it went out
3 of 3 people found this instruction helpful.
  • Thad from Layton, UT
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers
I pulled out the range from the wall unplugged it from the wall then i opened the oven door and removed the two small screws on the front off the range and lifted the glass top and supported it with a 1/2" X 18inc wooden dowel, then i removed the two burner retaining screws with a small Phillips screw driver and removed the wires from the burner,
then i replaced the burner with the new one and reconnected the wires and placed the burner in to the two retaining clips and then tightened the two screws then i removed the wooden dowel and installed the two screws on the front bottom side on the range then i plugged in the range in and tested the burner then put the range back against the wall.
Was this helpful?
Thank you for voting!
All Instructions for the JCSP47BF3BB
46 - 60 of 174