JCSP46WD1WW General Electric Range - Instructions

First and most important trun off curcit breaker. Use 1/4 inch but driver to remove socket (2) screws. Remove ground and hot wire clips from old socket, replace on new socket. Screw back into oven ceiling and turn on power. Reset clock and your are done. Very simple.

Disconnect the power to the oven at the main breaker panel. Open the oven door to the first stop (not all the way open) and pull straight up to remove the oven door from the hinge. Using a 1/4" drive ratchet with 1/2" extension with 1/4" socket, remove the 1/4" sheetmetal screw holding the temperature probe at the center of the broiler mo ... Read more unting plate. Remove the two 1/4" screws holding the broiler mounting plate. Remove the two 1/4" screws holding the broiler element at the ceiling of the oven. Pull the broiler element out from the back of the oven and there should be two electrical connectors at the back of the broiler element. Pull the electrical connectors off of element. Replace the element and re-install in reverse order.

Pull range out of the "hole", and spin so that back of range is accessible. Remove cover over top "control area" on back of range. (Four screws that happen to be the same size as the magnetic socket that holds the interchangeable tip on a cordless screw gun. Simply remove this tip, and use the tip holder as a magnetic nut driver!). Rem ... Read more ove the knob by pulling gently straight off. Remove black plastic retaining nut under where knob was. Inside are two small screws that hold the switch in place. Remove these screws with a magnetic screwdriver (If you drop these screws and lose them, you'll have a hard time finding them. Very small!!). Carefully follow enclosed instructions to move the wires from the old switch to the new switch. Put back together in reverse order.

The first thing was to watch U-Tube . The replacement burner was being
replaced in a GE glass top range. Exter tools were required than depicted
in the U-Tube project. The project overall was not dificult for me however I was a general contracter for over 25 years

had to remove the oven from the wall. once i realized that i had to take the side wall brackets off before removing the oven it was quite easy. then just had to remove oven door and slide the unit onto a chair while replacing the sensor. put it all back in and the wife was so happy to have her oven back she made me a batch of brownies. yu ... Read more m.

Disconnected the old socket ( 2 srews ) removed the two wires from the old socket, reconnected them to the new socket and reinstalled the lamp.

pull out stove, unbolt old temp sensor inside stove with 1/4 nutdriver, go to back of stove and take off cover and unhook sensor and hook up new one, put all back together and slide stove back in place.

Just like everyone else it was a simple r&r. However, when removing or installing wire clips I make it a habit to hold the ends with needle nose to prevent any: "snap!" ooops! However to prevent burning the element in the first place, it is strongly suggested to push that broil button twice so that it is set to low temp. It is too easy ... Read more to use the high setting which will shorten the elements life by 40 - 60 %. Also, keep the oven door partially open when using the broiler. Like the manual tells you!!!

First I removed the 4 screws that hold the element in place. I then pulled the element out about 3 inches. I removed the sensor and disconnected the connector.

. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two plugs.
plugged in the new element and screwed it in place

I pulled out the drawer and inserted the new support. This one inserts into the back of the drawer as opposed to the sides. I had ordered two of the replacements even though I only needed one and decided to replace both. I think it was a good move as the drawer works better than when we first got it. Just one simple screw made it com ... Read more plete.

Unplugged the Range and removed the two screws holding down the cook top. You do not need to remove the vent chamber at the rear of the range since the top lifts up about 4 inches. This should be enough room to get your hand onto the plug going to the door switch. Pull off the plug and remove the swich. Pop in the new one, put on the ... Read more plug, reinstall the two screws and you are done!

Read the thread on "burnt smell" and DO NOT assume it is a burned out element. Follow your nose!!