- Home
- JCSP39WT1WW
- Instructions
JCSP39WT1WW General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
oven coil caught on fire and broke in half!
2 of 4 people
found this instruction helpful.
-
Cynthia from Houston, TX
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Wrench (Adjustable)
I turned off the main power! Then unscrewed the back cover unhooked the wires and unscrewed the coil inside of the oven and pulled it out. My 10yr old son and I measured it and went online to order the part. I first did go into BestBuy and they didn't have the part (But they tried to sale me a new oven!) LOL Now who said a newly divorc
... Read more
ed mom couldn't fix her own oven! My Tech Support skills came in handy! Women Rock! LOL
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't heat - wire not exposed
1 person
found this instruction helpful.
-
Donald from Gulf Breeze, FL
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers
Removed two screws and removed the oven elelent. One wire was not through the back of the stove. Ordered new element anyway. Slid stove out (slide-in model). Unplugged power. Removed two covers protecting wires on back of stove. Found wire for oven element. Had to cut and strip end of wire and use new blade clip. Crimped new clip
... Read more
to wire and inserted into oven through back of stove. Replaced covers. Plugged oven element to wires and tried out oven. WORKED ! Saved new oven element for next time. Difficulty encounted was lack of knowledge on where stove was screwed into counter-top and what size blade clip to buy. It always helps to have a dog 3" away just itching to lend a paw.
Read less
Was this helpful?
Thank you for voting!
Heat element burned out
1 person
found this instruction helpful.
-
Donna from Thornville, OH
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
First unplugged it. Then removed everything in side for easy access. Took screws out 2 of them. Had to pull to removed elemnet . That took a while. Should have tried removing other screws or at less loosen them. It went in easy. And lift off we had red burner. hey..
Was this helpful?
Thank you for voting!
No heat lower bake unit / Broiler unit heats ok
1 person
found this instruction helpful.
-
Richard L. from Clear Spring, MD
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers
Safety first: Turn range circuit breaker to off position. Turn a surface unit [burner] to the on position ,if no light exists power has been removed. Turn surface unit to off position. To remove bake unit. With a 1/4 socket driver remove two self tapping screws and gently pull out on the bake unit until you can access the slide on
... Read more
terninals. Careful lenth of wire is limited. Remove slide on terminals two each [2] . Install new bake unit in reverse order . Restore power
Read less
Was this helpful?
Thank you for voting!
Element burned out.
1 person
found this instruction helpful.
-
lynette from Bowling Green, KY
- Easy
- 15 - 30 mins
-
Pliers
Flipped off the circuit breaker first. Unscrewed the two screws holding the element in place. Pulled out about 4-5 inches. Tried several times to pull apart the connections, finally got 'em - don't give up (I must have weak fingers). Then plugged in the new element, shoved the wires back in, screwed it back in place, flipped circuit br
... Read more
eaker back on, turned the oven on.... made brownies (o:
Read less
Was this helpful?
Thank you for voting!
Uns rewed and pulled out
1 person
found this instruction helpful.
-
Kathy from madison, WI
- Really Easy
- 15 - 30 mins
-
Wrench set
At first thought I was taking out some insulation but. "Clamp" just slid off and was very easy to install! Finding the right size socket took longer than the repair!
Was this helpful?
Thank you for voting!
element broke
1 person
found this instruction helpful.
-
Art from FRESNO, CA
- Very Easy
- 15 - 30 mins
-
Screw drivers
Fast shipping, Very easy to install I am a senior and had no problems works Great!!
Was this helpful?
Thank you for voting!
element broke
1 person
found this instruction helpful.
-
Richard from NEW BERLIN, NY
- Really Easy
- Less than 15 mins
-
Nutdriver
took 2 screws out that held element in, pulled old element out of oven wall, unhooked the wires. Hooked the wires to the new element, pushed it back into the oven wall, replaced the 2 screws.
Was this helpful?
Thank you for voting!
bake element was fried
1 person
found this instruction helpful.
-
William from MARTIN, GA
- Very Easy
- Less than 15 mins
-
Nutdriver, Pliers
I went by the video
Was this helpful?
Thank you for voting!
Oven would not heat
1 person
found this instruction helpful.
-
Franz from CRESTVIEW, FL
- Very Easy
- Less than 15 mins
-
Nutdriver
Removed old broken element and installed new one. Took less than 10 minutes
Was this helpful?
Thank you for voting!
Bake Element went out..flamed out pretty big light show when it happened
1 person
found this instruction helpful.
-
Don from Martin, TN
- Easy
- Less than 15 mins
-
Socket set
The job went over without a hitch, only probably didn't get the correct part first go around, but after getting the right part everything went very easy..Just a couple of screws where the elment goes in and 2 wires to plug back into the new element, after that everything was good to go!!
Was this helpful?
Thank you for voting!
The element on our three year old stove stopped working...this was the bottom bake element.
2 of 4 people
found this instruction helpful.
-
shawn from port richey, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
It was surprisingly simple. All I had to do was shut the breaker off to the stove(safety first). Next open the oven door and use a flashlight just to help you see,and unscrew the two screws holding the element in place on the back stove wall. Next slide the stove away from the was to give yourself enough room to access the back of it(you
... Read more
may need to unplug it to get it out far enough. My model had a cover over the back that took six easy to remove screws. Once the back cover was off I could easily see where the element was plugged into, so i removed the wires from the end of the element(just female terminals slipped over the end) i then went back to the front of the stove and pulled to element out.
To install the new one...just guide the two ends throgh the back of the stove...install the two screws to hold it in place...go to back of stove..plug in wires(they were diff sizes so you couldnt mess it up) and put the cover back on..plug in oven..slide it back..and try it out...its that simple
To install the new one...just guide the two ends throgh the back of the stove...install the two screws to hold it in place...go to back of stove..plug in wires(they were diff sizes so you couldnt mess it up) and put the cover back on..plug in oven..slide it back..and try it out...its that simple
Read less
Was this helpful?
Thank you for voting!
My heatng element blew up
2 of 4 people
found this instruction helpful.
-
Ruth from Charlotte, NC
- Really Easy
- Less than 15 mins
-
Nutdriver, Wrench (Adjustable)
I followed the way all the others on this website did the repair. It was so easy. I turned the power off to the oven, then disconnected it from the back oven wall, pulled it out a bit, disconnected the wires, and put it back in.
Then we put the power back on and stood back and turned on the stove and IT WORKED!!! Yeah, and ... Read more for so little money... I tell you I shopped other websites and this one was priced GREAT, and just reading the stories how others had done this repair gave me the confidence to do it too. Now, I think I have a burner that I will replace and who knows what else I can find to do.
THANKS SO MUCH!!!
Then we put the power back on and stood back and turned on the stove and IT WORKED!!! Yeah, and ... Read more for so little money... I tell you I shopped other websites and this one was priced GREAT, and just reading the stories how others had done this repair gave me the confidence to do it too. Now, I think I have a burner that I will replace and who knows what else I can find to do.
THANKS SO MUCH!!!
Read less
Was this helpful?
Thank you for voting!
The bottom bake element was burned out.
1 person
found this instruction helpful.
-
Richard from State College, PA
- Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
1. Turned off electrical breaker for range.
2. Removed the two hex head screws that hold element in place.
3. Pulled element out and unplugged the two electrical connectors.
4. Attached connectors to new element and attemped to push element back into the opening. It would not go in all the way.
5. Apparently some of t ... Read more he insulation had fallen down and was blocking the area where the element slides in.
6. I used a long thin screwdriver inserted into the two holes to push the insulation aside.
7. The element was then able to go in all the way.
8. Replaced two hex head screws.
9. Turned on range breaker.
10. Turned on oven. Works fine.
2. Removed the two hex head screws that hold element in place.
3. Pulled element out and unplugged the two electrical connectors.
4. Attached connectors to new element and attemped to push element back into the opening. It would not go in all the way.
5. Apparently some of t ... Read more he insulation had fallen down and was blocking the area where the element slides in.
6. I used a long thin screwdriver inserted into the two holes to push the insulation aside.
7. The element was then able to go in all the way.
8. Replaced two hex head screws.
9. Turned on range breaker.
10. Turned on oven. Works fine.
Read less
Was this helpful?
Thank you for voting!
bake element broke
1 person
found this instruction helpful.
-
edward from west sayville, NY
- Really Easy
- Less than 15 mins
-
Nutdriver
first i removed the two screws that hold the element in place. then pulled the element out about 3 inches and disconnected the two wires .then i connected the two wires and pushed thebake element back and replaced the two screws.then i put the circuit braker back on and tested the stove and it worked great. very easy to do.
Was this helpful?
Thank you for voting!