- Home
- JCSP28GT2BB
- Instructions
JCSP28GT2BB General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Lower bake element burned out.
1 of 2 people
found this instruction helpful.
-
Elaine from Hanover, PA
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
1. Turned off power at the breaker box. Removed oven door from oven, and removed bake racks. Determined replacement element from PartSelect was correct. Inspected new element. Using meter, determined new element was OK via continuity test. Gathered all appropriate tools to do the job.
2. Using 1/4" nut driver, removed two reta ... Read more ining screws at back of oven that secure element
3. Pulled bad element out a few inches from oven back to reveal wires and spade connectors
4. Using screwdriver, pushed off electrical connectors from bad element and removed element
5. Inspected wires and connectors and determined them to be OK
6. Installed new element in reverse of above. Inspected oven controls and determined them to be OK. Turned on the breaker. Tested oven.
7. Baked a delicious chocolate cake
2. Using 1/4" nut driver, removed two reta ... Read more ining screws at back of oven that secure element
3. Pulled bad element out a few inches from oven back to reveal wires and spade connectors
4. Using screwdriver, pushed off electrical connectors from bad element and removed element
5. Inspected wires and connectors and determined them to be OK
6. Installed new element in reverse of above. Inspected oven controls and determined them to be OK. Turned on the breaker. Tested oven.
7. Baked a delicious chocolate cake
Read less
Was this helpful?
Thank you for voting!
Broken plastic handle end caps
1 of 2 people
found this instruction helpful.
-
Joseph from PITTSBURGH, PA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Step #1: Remove 2 screws at the inside top of the oven door that holds the inner/outer oven door together. Step #2: Remove the screws from the inner door that hold the plastic handle end caps to the door. Tip: Use a file to dress up the tips of the metal handle bar so that it fits easily into the new plastic handle end caps. Step #3
... Read more
: Install the first new plastic handle end cap. Step #4: Slide the metal handle bar into the plastic handle end cap that was just installed on the outer oven door. Step #5: Place the other plastic handle end cap on the metal handle bar. Step #6: Install the second plastic handle end cap on the outer oven door. Step #7: Reassemble the oven door by installing the screws that were removed in step #1.
Read less
Was this helpful?
Thank you for voting!
burned out
1 of 2 people
found this instruction helpful.
-
David from Woodbridge, VA
- Really Easy
- Less than 15 mins
-
Nutdriver
My dealer was unable to find the part even with a model number. Your accurate drawings allowed me to select correct part. It was a perfect replacement in every way and cheaper (by $10) than the dealer. Also quicker.
Was this helpful?
Thank you for voting!
Double Oven door handles were off because of broken end pieces
1 of 2 people
found this instruction helpful.
-
David H. from Arkadelphia, AR
- Easy
- Less than 15 mins
-
Screw drivers
Unscrewed three screws from each oven door. Unbolted the end pieces and replaced with new ones. Reinstalled oven door screws. Nothing to it.
Was this helpful?
Thank you for voting!
Bake element broken
1 of 2 people
found this instruction helpful.
-
Charles from Damascus, MD
- Easy
- Less than 15 mins
-
Wrench (Adjustable)
Before ordering, I took the element out to make sure I could do it. A flashlight was helpful.
I flipped off the circuit breakers to the stove, removed the racks and lifted off the oven door. Not having a nutdriver or socket set, I used a 6' crescent wrench to remove the two screws which hold the element to the back of the oven ... Read more . I carefully pulled the element out until the spade connectors to the wires were exposed. I wiggled the connectors apart. I had pliers handy, but didn't need them.
I connected the new element to the wires and gently pushed the two connected prongs through their holes, trying not to disturb the insulation. I put a little WD-40 on the screws so they would go in easier. After tightening the screws with the crescent wrench, I replaced the racks and door. I flipped the circuit breaker back on and reset the clock. It works as good or better than new.
I flipped off the circuit breakers to the stove, removed the racks and lifted off the oven door. Not having a nutdriver or socket set, I used a 6' crescent wrench to remove the two screws which hold the element to the back of the oven ... Read more . I carefully pulled the element out until the spade connectors to the wires were exposed. I wiggled the connectors apart. I had pliers handy, but didn't need them.
I connected the new element to the wires and gently pushed the two connected prongs through their holes, trying not to disturb the insulation. I put a little WD-40 on the screws so they would go in easier. After tightening the screws with the crescent wrench, I replaced the racks and door. I flipped the circuit breaker back on and reset the clock. It works as good or better than new.
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't heat bottom
1 of 2 people
found this instruction helpful.
-
Thomas N from Blackfoot, ID
- Really Easy
- Less than 15 mins
-
Nutdriver
.First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and reversed the procedure with the new element very simple.
Was this helpful?
Thank you for voting!
Baking element burned through.
1 of 2 people
found this instruction helpful.
-
James from Seattle, WA
- Easy
- Less than 15 mins
-
Nutdriver
First I removed the two screws that hold the element in place, I then pulled the element out about three inches, and it shorted out on the main panel of the back of the range. I then went to the breaker box and flipped the switch so I could tell my wife "Yes, I had turned the power off."
Disconnecting the two wires and recon ... Read more necting them was a simple operation after I cleaned my pants from the electrical short.
Re attaching the two-screw panes to hold the element in place finished the project.
Disconnecting the two wires and recon ... Read more necting them was a simple operation after I cleaned my pants from the electrical short.
Re attaching the two-screw panes to hold the element in place finished the project.
Read less
Was this helpful?
Thank you for voting!
The oven heating element broke in two.
1 of 3 people
found this instruction helpful.
-
Anna from Texas City, TX
- Really Easy
- Less than 15 mins
-
Socket set
Rating: 5 Stars!! We cut the power, removed two screws disconnected the two wires (just pulled them out of the covers) from the old element and pushed in the new ones. It didn't take longer than 10 minutes!
This is the first time it's been as easy as promised! Great customer service in addition to easy and reasonable prices ... Read more !
Thank you,
This is the first time it's been as easy as promised! Great customer service in addition to easy and reasonable prices ... Read more !
Thank you,
Read less
Was this helpful?
Thank you for voting!
Lower bake element shorted out.
1 of 3 people
found this instruction helpful.
-
Val Ray from Idaho Falls, ID
- Really Easy
- Less than 15 mins
-
Nutdriver
1st, Turn off the stove at the electrical box. 2nd, Remove the oven door by opening it to the first stop, and then pulled it straight up. 3rd, Remove the 2 screws using a 1/4" nut driver. 4th Pull the old heating element straight out, until the two wires that attach to the element are out 3" from rear oven wall. (Note: Place a peace o
... Read more
f tape around each wire before disconnecting from the element. this will keep the wires from falling back through the holes). Remove the wires from the old element and remove the old element. 4th Place the new element into the oven, place the wires onto the new element. Then reverse the order of removal for new element install, for the repair. Less than 10 minutes.
Read less
Was this helpful?
Thank you for voting!
wasn't heating anymore
0 of 1 people
found this instruction helpful.
-
nelson from milan, IN
- Really Easy
- Less than 15 mins
-
Nutdriver
orderd a replacement part. recieved it two days later then that evening installed it. there was a video online to show how to replace it. very useful if your not a do it yourselfer.
Was this helpful?
Thank you for voting!
A few days before Christmas, my lower oven heat element went out.
0 of 1 people
found this instruction helpful.
-
Patsy from Rosharon, TX
- Really Easy
- Less than 15 mins
-
Socket set
I went on-line, found Partselect.com, they gave me the part number, showed me a video on the repair details, shipped the part overnight, and within ten minutes of the arrival of the part, I was up and running. EXCELLENT SERVICE! Thanks for saving Christmas at our house!!
Was this helpful?
Thank you for voting!
Element not working
0 of 1 people
found this instruction helpful.
-
Louis M from South Salem, NY
- Really Easy
- Less than 15 mins
-
Nutdriver
You literally saved our Christmas from a disaster! Four days before Christmas our bake element gave out and we discovered it had split. We found you on the Internet, ordered the part, and prayed you would deliver as promised. We received it the next day, as promised, and in time to cook Christmas dinner. It was a snap to install, lite
... Read more
rally took five minutes. Your service, response time and instructions were perfect. Keep up the good work!
Read less
Was this helpful?
Thank you for voting!
Oven would not heat
0 of 1 people
found this instruction helpful.
-
Sheryl from Pahrump, NV
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
I watched the video on the website then installed the part. In fact, I watched the video twice because I could not believe it was that easy. You can not do any better than PartSelect. Shipping is fast and the instructions are great. If I ever need a part for any appliance I will go to PartSelect.com first. Keep up the great work and thank
... Read more
-you so much!
Read less
Was this helpful?
Thank you for voting!
Old element shorted out after Thanksgiving (thankfully)
0 of 1 people
found this instruction helpful.
-
Mary from Matthews, NC
- Really Easy
- Less than 15 mins
-
Socket set
We were able to purchase the part and replace it for under $25. We took off the oven door and installed the new element in under 10 minutes.
Was this helpful?
Thank you for voting!
20 year old oven bake element became brittle and pieces broke off, overheated and partially melted, one side touching bottom of oven, caused very slow heatup.
0 of 1 people
found this instruction helpful.
-
Leonard from Framingham, MA
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers
Removed nuts holding element to rear of oven using nut driver, pulled wires out 3 inches and disconnected using needle nose pliers, installed new element. Job took 10 minutes - very easy job and works fine.
Was this helpful?
Thank you for voting!