- Home
- JCS968BF6BB
- Instructions
JCS968BF6BB General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The large front right burner of the radiant cooktop did not work
-
Arthur from Sarasota, FL
- Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Turned off the power at the breaker. Then I lifted the cooktop by pressing up from the bottom, while my wife slid two boards over the recess. I lowered the cooktop onto the boards, removed 12 screws around the perimeter of the case and carefully lifted the glass top and placed it on a towel on the DR table. (remove the control knobs first
... Read more
) removed the wires leading to the infinite control, marking which color when where, removed the two screws holding the infinite control, and replaced the old with the new. Reattached the wires, replaced the cooktop, replaced the screws, held it up while my wife removed the boards and then carefully lowered the cooktop into the recess. Attached the knobs, flipped the breaker back on and turned control to hi. It worked!
Read less
Was this helpful?
Thank you for voting!
Stove drawer rear guides broken
-
Robert from Shakopee, MN
- Really Easy
- Less than 15 mins
-
Nutdriver
Installed new guides with a nut driver without any problems.
Was this helpful?
Thank you for voting!
Our bottom drawer support broke and the bottom drawer was canted
-
Robert from Woodinville, WA
- Really Easy
- Less than 15 mins
-
Screw drivers
Simply removed drawer and lined up the newsupports. Made sure the guide pin was lined up and installed with single screw
Was this helpful?
Thank you for voting!
Oven Probe broke
-
Kathleen from Munt Laurel, NJ
- Really Easy
- Less than 15 mins
Ordered new probe
Was this helpful?
Thank you for voting!
Plastic slide for storage drawer broken.
-
James from Stuart, VA
- Really Easy
- Less than 15 mins
-
Screw drivers
Took part out of package, looked at instructions and followed them. Required a screwdriver to screw part on to the drawer.
Was this helpful?
Thank you for voting!
missing meat thermistor
-
John R from Asheville, NC
- Really Easy
- Less than 15 mins
plug in thermistor when needed
Was this helpful?
Thank you for voting!
Range lower drawer would not stay on track.
-
Richard from Newark, DE
- Really Easy
- Less than 15 mins
-
Nutdriver
Easy to install replacement parts using the screws provided.
Was this helpful?
Thank you for voting!
Broken drawer support
-
Mario from Deer Park, WA
- Really Easy
- Less than 15 mins
-
Nutdriver
Followed the example picture on the part bag. Anyone could do this, incredibly easy. Took about 4 minutes to install both sides.
Was this helpful?
Thank you for voting!
Convection motor making loud clunking noise
-
Lynette from Rapid City, SD
- Easy
- 30 - 60 mins
-
Nutdriver, Socket set
Turned off power to range, slid range out from counter, removed convection fan cover, removed convection fan blade, removed back of range panel over convection motor, removed motor, put in new motor, put range panel back on, put new fan blade on front of motor, replaced fan cover, turned power on. No more clunking noise from motor.
Other Parts Used:
Was this helpful?
Thank you for voting!
large burner on the dual element not working
-
Alan from Medina, OH
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
The part arrived much sooner than I anticipated. The job was a little harder and took a little longer for me because I'm not good at repairing things. I usually have to call someone. However, I followed the step by step instructions that were provided both on the website and with the mailed item and had no problems. The instructions w
... Read more
ere clear and easy to follow. The tools needed were very basic - all of which I had on hand. If I could do it - anyone can.
Read less
Was this helpful?
Thank you for voting!
one leg of the terminal block was loose and overheated under load.the terminal block melted and could have caused a fire.
-
brendan from lebanon, NH
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set, Wrench set
I took a picture of the setup and damage . I then disconnected the burnt wires and replaced the wires . Then I installed the new terminal block and connected the wires to the proper positions. The reason for the failure was that the delivery people didn't tighten the cord when they installed the stove . I would check the connections per
... Read more
iodically as to avoid another situation like this .
Read less
Was this helpful?
Thank you for voting!
Broiler Element burnt out
-
Cherri from Katy, TX
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver
The actual repair was relatively easy but access to the area in the oven made it a little difficult. Just unscrew 5 screws with a nut driver, unplug the old element, plug in the new element and reinstall the 5 screws. The only thing that made this repair difficult was being able to reach the connectors where you plug in the new element.
... Read more
They are loose wire connectors that don't reach very far out of the element receptacle. It was difficult to hold the end of the connector and plug in the new element because the oven door is in your way. Maybe it is easier if you take the oven door off first?
Read less
Was this helpful?
Thank you for voting!
Broil element on top oven was not working
-
andrew from pittstown, NJ
- Easy
- 30 - 60 mins
-
Socket set
Shut the power off at the electric box.Disconnected coil from roof clips.Pulled wire connection from back wall. Disconnected wire clips, connected new unit.Clipped to roof and turned on" Working fine".
Was this helpful?
Thank you for voting!
Twisting of stuck cook-top killed the event
-
James from Kingsville, MD
- Difficult
- 30 - 60 mins
-
Screw drivers
The age of the system resulted in the cook top being heavily stuck by food-stuff to the range surface. The result was a twisting of the top when breaking it free. It caused the cooktop (a $500+ part) to crack diagonally across the whole surface. Thus ended the quick do-it-yourself process, and out to buy a new range. Parts-select was
... Read more
very good about the return process of the un-used and un-opened burner element.
Read less
Was this helpful?
Thank you for voting!
burner worked on high only
-
Carl from Delray Beach, FL
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Followed directions from Rodney of Erath La. Directions were perfect and helped me to decide to under take this job. Job took a little longer spending some time to clean the glass top on both sides and around the counter top where it mounts. The actual repair time was quick and easy thanks to Rodney. Price of the part was reasonable an
... Read more
d delivery got here quick. Will deal with parts select again! Carl from Florida
Read less
Was this helpful?
Thank you for voting!