JCS66*W3 General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
burner would not lay flat against surface of range.
3 of 4 people
found this instruction helpful.
-
John from Westbrook, ME
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Removed two clips that held the ceramic insulators in place. Removed two screws that held conductors to the burner. Replaced screws onto new burner unit, replaced ceramic insulators. Fastened clip to burner onto the range. Turned burner on and it worked great. Thank you for your quick responce to my order.
Was this helpful?
Thank you for voting!
Replaced the bake element (lower element) in the small oven
2 of 2 people
found this instruction helpful.
-
Marcia from SALEM, OR
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Disconnected range from power. Removed small / lower shield that protects element connectors from rear of range. Disconnected the power lines from the element using screwdriver. Removed racks and liner from oven. Removed screws at rear of oven box that hold old element. Removed the old element. Reversed steps to install replacement
... Read more
heating element. Tested oven heating using oven thermometer.
Read less
Was this helpful?
Thank you for voting!
heating element went out
2 of 2 people
found this instruction helpful.
-
vanessa from DARBY, PA
- Really Easy
- 30 - 60 mins
-
Socket set
replace with new one
Was this helpful?
Thank you for voting!
Burner wouldn't operate
3 of 5 people
found this instruction helpful.
-
Linda from Hindman, KY
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Took Switch panel off range. Disconnected Infinite switch. Reinstalled infinite switch.. Replaced panel. Repair was very simple and self explainatory.
Knott County Housing Authority Maintenance Personnel
Knott County Housing Authority Maintenance Personnel
Was this helpful?
Thank you for voting!
Up to 1 hour for oven to preheat
2 of 2 people
found this instruction helpful.
-
Joel from Avon, OH
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Removed 2 nuts holding the baking unit to the oven back, removed 2 nuts holding wires in place, installed new unit following procedure backwards. It takes longer to get the tools,take the oven door off, and take racks out than it does to remove and replace the baking unit.
Was this helpful?
Thank you for voting!
Bake element began to spark and short out when I tried to use it.
2 of 2 people
found this instruction helpful.
-
Bill from MANHATTAN, KS
- Really Easy
- 1- 2 hours
-
Screw drivers
When the part arrived, I used the diagram provided by the website to see what really needed to be done. Keep in mind, if you're doing it correctly and disconnect the range from the power source, it's going to be dark inside the oven. Get a good flashlight or electric lantern. There are two screws holding the element in. Mine were 8MM hex
... Read more
-head screws, but be prepared for anything. I removed the with a socket attachment/adapter to my cordless drill/screwdriver, and the part came right out. Some insulation will come as well - don't panic. Installation is similar, just in reverse order. Pay attention to the feet on the element. Make certain they are down. Don't lean on them when you think you're finished and discover that you installed it upside down like someone I know, and have to pull it out to correct this.
Read less
Was this helpful?
Thank you for voting!
Burner won't heat
4 of 8 people
found this instruction helpful.
-
George from Sarasota, FL
- Easy
- 1- 2 hours
-
Pliers, Screw drivers, Wrench set
Replaced the burner. Still no heat. Decided to take the front off and test the connections (Power Off!). Found no output from switch to burner. Ordered new switch from PartSelect. Switch arrived in 24 hours, just like the burner (I'm in FL, but still fast!) My only problem was that the know didn't quite fit -- too long. Cut the meta
... Read more
l correctly, but still too long. Had to cut the plastic adapter slightly. Now it fits like the others, but it's not quite as secure due to shortening the piece that slides on the metal shaft.
Read less
Was this helpful?
Thank you for voting!
element burned out
2 of 3 people
found this instruction helpful.
-
Jeff from Westport, IN
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Took off the door, took out the two screws in the back of the element. Then pulled the element forward, then removed the two wires. Then put it all back together with the new element.
Was this helpful?
Thank you for voting!
Oven Heating element broken
2 of 3 people
found this instruction helpful.
-
James from Hanover, MA
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Turned off power to the oven at the circuit breaker. Pulled the old heating element from the back lower wall of the oven. Noted the position of the wires (right terminal attached to the red wire, left to the black wire). Removed small bolts holding the element to the wires using pliers. Attached the new element using screw driver. New ele
... Read more
ment came with screws, not bolts. Pushed the element back into place and restored power. Tested to make sure everything worked. Everything works and I ran an oven cleaning cycle. Noticed that indicator light above the temperature selctor is always on now even when oven is in the OFF position. Not sure if that's related to the change or to the oven cleaning cycle I ran. In any case, oven seems to work normally.
Read less
Was this helpful?
Thank you for voting!
Bottom oven heating element was out
1 person
found this instruction helpful.
-
John from FALL RIVER, MA
- Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Very easy repair. 2 hex head screws to take the heating element out. Then 2 more slot head screws for the wire connections. Perfect fit and operation of the new heating element.
Was this helpful?
Thank you for voting!
Heating Element Was No Longer Working.
1 person
found this instruction helpful.
-
Karen from Stuart, FL
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
Removed oven door by holding sides and pulling upward. It's easy to remove and replace. Removed shelves by sliding back and up, then out. Removed two hex nuts with socket wrench. They are on back wall of oven and secure element to that wall. I then pulled element out about 3 inches and disconnected the two leads.
I put new ... Read more element in, reconnected two leads, replace two hex nuts and was done.
Turn off power to stove at circuit breaker before starting.
I put new ... Read more element in, reconnected two leads, replace two hex nuts and was done.
Turn off power to stove at circuit breaker before starting.
Read less
Was this helpful?
Thank you for voting!
Bottom Bake Element had burnt into/split
1 person
found this instruction helpful.
-
Miranda from UNION GROVE, NC
- Really Easy
- Less than 15 mins
-
Socket set
Very easy and simple/ After making sure power supply was off, removed socket screws in back plate of element, slid old element out, attached new element and replaced/tightened socket screws on plate and new element. Power on, oven on .. heated quickly and nicely. Used oven several times since ... no problems.
Was this helpful?
Thank you for voting!
Bake Element Burnt Out On Upper Oven
1 person
found this instruction helpful.
-
GREGORY from HOUSTON, TX
- Really Easy
- Less than 15 mins
-
Nutdriver
Unscrewed the element from the oven,disconnected the two screws for the electrical and reverse the procedure to install new element. Took all of about 10 minutes.
Was this helpful?
Thank you for voting!
Baking element had burned out and actually cracked in half.
1 person
found this instruction helpful.
-
Marie from Roxboro, NC
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
It was so simple, I turned off the breker to the oven, unscrewed two screws holding in the element, pulled out until the wire connetion was exposed. I unscrewed those two screws, then placed the replacement part, put the two screws on, pushed back the wiring and insulation.Final step was screwing two screws to hold the unit to the oven ba
... Read more
ck. So simple! The part was ordered regular mail and still was here in 2 days. Will recommend to friends for sure!
Read less
Was this helpful?
Thank you for voting!
Replacing the bake element
1 person
found this instruction helpful.
-
Ken from Lexington, KY
- Really Easy
- Less than 15 mins
-
Pliers
I couldn't find the oven model number so I just looked at the shapes from partselect.com. This would have been fine except I didn't know my Kenmore model had 4" leads so the one I ordered were only 2". I had to return the first element but the process to do this was FAST and EASY. With help I found the model number and had the correct par
... Read more
t shipped. It took less than 5 minutes to install. It took longer to mop and clean behind the oven that hadn't seen the light of day in 10 years.
Read less
Was this helpful?
Thank you for voting!