JCP682W4 General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Lower baking element had burned out.
1 person
found this instruction helpful.
-
Rob from Las Cruces, NM
- Really Easy
- Less than 15 mins
-
Nutdriver
Using a nut driver, I removed the two screws holding the baking element to the firewall of the oven. I then pulled the baking element out exposing the two wires connected to it. I then used the same nutdriver to remove the nuts and detached the old element. I then connected the new element to the wires, pushed the wires inside the firewal
... Read more
l and reattached the element to the firewall of the oven.
The time it took was literally a few minutes. Works like a new oven!
The time it took was literally a few minutes. Works like a new oven!
Read less
Was this helpful?
Thank you for voting!
Bake Element Burnt Out On Upper Oven
1 person
found this instruction helpful.
-
GREGORY from HOUSTON, TX
- Really Easy
- Less than 15 mins
-
Nutdriver
Unscrewed the element from the oven,disconnected the two screws for the electrical and reverse the procedure to install new element. Took all of about 10 minutes.
Was this helpful?
Thank you for voting!
Baking element had burned out and actually cracked in half.
1 person
found this instruction helpful.
-
Marie from Roxboro, NC
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
It was so simple, I turned off the breker to the oven, unscrewed two screws holding in the element, pulled out until the wire connetion was exposed. I unscrewed those two screws, then placed the replacement part, put the two screws on, pushed back the wiring and insulation.Final step was screwing two screws to hold the unit to the oven ba
... Read more
ck. So simple! The part was ordered regular mail and still was here in 2 days. Will recommend to friends for sure!
Read less
Was this helpful?
Thank you for voting!
Oven heating element failed
1 person
found this instruction helpful.
-
megrew, from COLORADO SPGS, CO
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Identify oven breaker and turn off power before starting. Opened oven door. Removed oven racks. Use 1/4" socket or nut driver to remove the 2 bolts holding heating element mounting bracket at rear base of oven. Carefully pull element out of installation mount to remove the 2 machine screws that attach electrical wires to the heating eleme
... Read more
nt. Reattach wires in same order as original element. Then reinstall new element in reverse order of removal. Took all of maybe 15 minutes! Excellent OEM Parts!
Read less
Was this helpful?
Thank you for voting!
Element burned out
1 person
found this instruction helpful.
-
Wendy from CHESHIRE, CT
- Really Easy
- 15 - 30 mins
-
Socket set
My husband first turned the main breaker off to the stove. Pulled the stove away from wall, took off the back plate, unhooked the element and out the new one in!!
Was this helpful?
Thank you for voting!
Really old range. Broken bake element in oven.
1 person
found this instruction helpful.
-
Kathleen from Grand Rapids, MI
- Very Easy
- Less than 15 mins
Turned off power. Removed old broken one installed new one in minutes. Turned power on and tested it out. If this 60 something lady can do it, you can too.
Was this helpful?
Thank you for voting!
Oven element burned out.
1 person
found this instruction helpful.
-
Carol from STONY BROOK, NY
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Turn off electricity to the oven. A socket set was needed for the small screws in my old oven. Once the screws were removed the element came off easily from two wires in the oven. You have to be careful when handling the wires that they don’t fall back into the oven. The new part was attached to the two wires, screws were tightened on the
... Read more
new element and that was it. When the oven was turned on the new element smoked a little but I saw on the video that is normal.
Read less
Was this helpful?
Thank you for voting!
Oven lower Bake Element exploded
1 person
found this instruction helpful.
-
Fred from Renton, WA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Socket set
First observed the situation to determine if I should try and repair. I decided I could and should. Got the element and proceeded. I first turned the power off at the circuit breaker to cut the electrical power to the stove then I removed the two screws that holds the unit in place and then pulled unit out to where I could see the wire co
... Read more
nnection; removed the two screws on the wire connection and replaced the old element with the new element. reinserted the unit back into position and replaced the two screws that holds the unit in the stove. Turned power back on and tested the oven for any problems. Stove is working great.
Read less
Was this helpful?
Thank you for voting!
bake element no heat
1 person
found this instruction helpful.
-
larry from buckhannon, WV
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
took old element out , put new element in.very easy.
Was this helpful?
Thank you for voting!
Bottom Element On The Top And Bottom Oven Burned Out
1 person
found this instruction helpful.
-
Tammy from McKinney, TX
- Really Easy
- 15 - 30 mins
-
Wrench set
Just like your example said/turn the power off to the oven/remove the screws that hold the element in place and then I pulled th element out a little ways and disconnected the wires/reconnecting took a little longer only because it was hard to see/but I connected the two wires and put the screws back in and it worked. Saved me a lot of m
... Read more
oney/my husband wanted to get a new double oven
Read less
Was this helpful?
Thank you for voting!
Bake element shorted and broke
1 person
found this instruction helpful.
-
David from Littleton, CO
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
TURN OFF CIRCUIT BREAKER before doing anything even if oven is not turned on! If I hadn't checked voltage with tester before starting I would have made a shocking discovery.
1) unscrewed shield cover to get get at the element screws.
2) unscrewed element screws and removed old element - pulling connecting wires out about 3 inch ... Read more es
3)attached new element to connecting wires (2 screws)
4) pushed new element into place and reattached element connector plate to wall of oven
5) reattached shield cover to wall of oven
1) unscrewed shield cover to get get at the element screws.
2) unscrewed element screws and removed old element - pulling connecting wires out about 3 inch ... Read more es
3)attached new element to connecting wires (2 screws)
4) pushed new element into place and reattached element connector plate to wall of oven
5) reattached shield cover to wall of oven
Read less
Was this helpful?
Thank you for voting!
The bottom oven heat element didn't work
1 person
found this instruction helpful.
-
Marilee from Newburgh, IN
- Easy
- 15 - 30 mins
-
Pliers, Socket set
1. Removed the old element. Had a little trouble loosening the screws. After we got them loose, everything was easy.
2. Pulled out the element and disconnected the wires.
3. Connected the wires on the new element.
4. Screwed the element back in.
5. Connected the stove and turned on the oven.
6. It works like a ne ... Read more w one.
2. Pulled out the element and disconnected the wires.
3. Connected the wires on the new element.
4. Screwed the element back in.
5. Connected the stove and turned on the oven.
6. It works like a ne ... Read more w one.
Read less
Was this helpful?
Thank you for voting!
The bake element burned in half.
1 person
found this instruction helpful.
-
RICHARD from BETHLEHEM, PA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
First I turned the power off to the oven/stove at the breaker box in the basement. Then I took the back plate off. Then I removed the two screws holding the wires onto the damaged element. Then I removed the two screws holding the element to the inside rear of the oven. Then I pulled the old element out and replaced it with the new elemen
... Read more
t. I replaced the two screws that hold the element to the inside of the oven. Then I replaced the wires on the element where it protruded at the back of the oven. I put the back plate back on, slide the oven back in place and turned the power back on at the breaker and everything worked.
Read less
Was this helpful?
Thank you for voting!
Baking element no longer worked.
1 person
found this instruction helpful.
-
Stanley from Cave Creek, AZ
- Really Easy
- 15 - 30 mins
-
Nutdriver
Removed 4 screw nuts and replaced with new baking element using same 4 screw nuts. Real easy job.
Was this helpful?
Thank you for voting!
Bake element burnt out
1 person
found this instruction helpful.
-
David from West Union, AL
- Easy
- 15 - 30 mins
-
Nutdriver
Firs I shut the power off to the range. Then I removed the bottom oven rack, then removed the two screws holding the element in place. I pulled the element out about 3 inches to pull the connecting wires off. However, when I pulled the element towards me a lost on of the connecting wires that attached to the element. I then had to pull th
... Read more
e range away from the wall and remove the back cover panel.I then fed the new element into the wholes from the inside of the range and having the back panel removed gave me full access for reconnecting the element wires. I put the back cover panel into place , put the bottom oven rack in and that was it. I was done with the repair. I turned the power back on and everything worked fine. I would recommend removing the back cover panel prior to trying to remove the element. This will save you some time and give you full access to the wiring before attempting to remove the bake element.
Read less
Was this helpful?
Thank you for voting!