JCKS05GP1 General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven would not heat
0 of 1 people
found this instruction helpful.
-
KY from Lenapah, OK
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers
Turned off power to oven. Removed two screws that hold the element in place. I then pulled out the element far enough to get to the wires so I could disconnect them. I connected the new element and screwed it back in. 10 mins tops!!!
Was this helpful?
Thank you for voting!
broken element
0 of 1 people
found this instruction helpful.
-
Marsha from Charlotte, NC
- Really Easy
- Less than 15 mins
-
Nutdriver
turn of electric oven, removed screws and took out old element and put in new element and replaced screws. done simple and easy
Was this helpful?
Thank you for voting!
Baking Element wouldn't heat but the broiler worked fine.
0 of 1 people
found this instruction helpful.
-
Lynne from Coto de Caza, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
First I turned off the power at the fuse box, then removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and replaced with the new element. Very Easy!
Was this helpful?
Thank you for voting!
The baking element broke.
0 of 1 people
found this instruction helpful.
-
Toni Ann from Manalapan, NJ
- Really Easy
- Less than 15 mins
Ordering and shipment of the part were quick and easy. The price was excellent too. It was the easiest repair we ever had to do to an appliance. After removing the screws that held the element in place and disconnected the part, my husband immediately connected the new part. It took less than 15 minutes.
Was this helpful?
Thank you for voting!
timer and cleaning timer knobs broken
0 of 2 people
found this instruction helpful.
-
Alexis from Birch Run, MI
- Really Easy
- Less than 15 mins
two of the knobs pushed on perfectly,
Other than that they came quickly and I loved the service.
Thank you
Other than that they came quickly and I loved the service.
Thank you
Was this helpful?
Thank you for voting!
element burned out
0 of 2 people
found this instruction helpful.
-
Edward from Colville, WA
- Really Easy
- 15 - 30 mins
-
Nutdriver
removed and replaced
Was this helpful?
Thank you for voting!
Only able to get 1 little knob on
0 of 7 people
found this instruction helpful.
-
Phyllis from Austin, TX
- Very Difficult
- More than 2 hours
You are supposed to be able to just pop them on. Got one on the two others will not go on.
Help!
Help!
Was this helpful?
Thank you for voting!
Broil element burned out, literally!
-
Judith from Franklin, NC
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
Turned off power to oven. Lifted off the oven door. Removed four 1/4 " bolts from outside of fan housing. Removed two 1/4" bolts holding element. Removed element from three clips holding it to upper oven surface. Unplugged two element wires. Reassembly was the reverse. I am an auto mechanic by trade and this was a fairly simple process.
Was this helpful?
Thank you for voting!
Timer knobs were missing
-
Ellen from Gainesville, FL
- Easy
- Less than 15 mins
They were easy to install - just push them on! I did need to line up the tab inside the knob with the notch on the metal control, but once I did that, it was easy to pop them on.
Was this helpful?
Thank you for voting!
Broken element
-
Herman from Norman Park, GA
- Really Easy
- Less than 15 mins
-
Nutdriver
Used nut driver, removed 2 screws and removed old element. Reversed procedure for installion of new part. Can't believe ordered part one day & recieved it next day. Fantastic service. Will definitely call company again.
Was this helpful?
Thank you for voting!
Bake element caught fire and started sparking
-
CORY from CARY, NC
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers
Installation was really easy. Remove the old bake element, plug the new one in, took at most 10 minutes.
Was this helpful?
Thank you for voting!
Broiler element
-
Jess from Edmond, OK
- Very Difficult
- 15 - 30 mins
-
Nutdriver, Pliers
I tried to unplug old element without success. Called appliance repair man and he pulled part way out, took hold of place where plugged in with pliers and unplugged. While holding back part of plug he plugged in new element--$60.00 later.
Was this helpful?
Thank you for voting!
Broiler element replaced as well as oven door seal.
-
---Tim from selma, NC
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Turn off breaker to oven from electrical panel, locatge all screws and remove. Use caution when removing element from clips if not replacing the clips. When removing the element, be careful not to damage connecting wires as they do not pull out very far. Be sure to reattach correctly. When replacing the oven seal, be careful not to discon
... Read more
nect the wires to either element as you slide the oven compartment forward after removing screws. It can be difficult to find the wires behind the oven compartment if they disconnect.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Replace Broiler Element
-
Mike from Davisburg, MI
- Easy
- 15 - 30 mins
-
Socket set
The whole job took about 20 min. TURN POWER OFF AT CIRCUIT BREAKER!! Remove 4 screws from the convection cover, then 2 more holding in the broiler element, disconnect 2 wires, and connect to the new one. put the screws back in, the cover back on the convection element and you are done!
Was this helpful?
Thank you for voting!
Oven broiler stopped working. Had to replace the broiler element.
-
Don from Los Altos, CA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers, Socket set
Just like the other responses described with two additional steps: 1) with a convection oven you have to remove the fan cover. It has four screws, the same size as the broiler element screws....but, get a piece of stiff cardboard the same width as the oven; put it all the way back, under the fan cover. There are holes in the oven bott
... Read more
om and your screws really want to roll into those holes and disappear; the cardboard will cover the holes. 2) as soon as you disconnect the element from the electrical wires....put a twist tie or other clamp on each wire as they want to fall back in behind the oven and you'll end up having to remove the build oven to get at the wires. The twist tie should keep them from falling out of reach.
Read less
Was this helpful?
Thank you for voting!