JCKP13GP1 General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
broken element
0 of 1 people
found this instruction helpful.
-
Marsha from Charlotte, NC
- Really Easy
- Less than 15 mins
-
Nutdriver
turn of electric oven, removed screws and took out old element and put in new element and replaced screws. done simple and easy
Was this helpful?
Thank you for voting!
Baking Element wouldn't heat but the broiler worked fine.
0 of 1 people
found this instruction helpful.
-
Lynne from Coto de Caza, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
First I turned off the power at the fuse box, then removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and replaced with the new element. Very Easy!
Was this helpful?
Thank you for voting!
Oven would not heat
0 of 1 people
found this instruction helpful.
-
KY from Lenapah, OK
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers
Turned off power to oven. Removed two screws that hold the element in place. I then pulled out the element far enough to get to the wires so I could disconnect them. I connected the new element and screwed it back in. 10 mins tops!!!
Was this helpful?
Thank you for voting!
Oven Element melted
0 of 1 people
found this instruction helpful.
-
Eugene from San Rafael, CA
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers
Turned off power. Removed two screws. Took out old element. Used pliers to remove connectors. Installed new element. Set screws. Turned on power. Works.
Was this helpful?
Thank you for voting!
Element burnt through
0 of 1 people
found this instruction helpful.
-
frederick from kingwood, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver
Repair was very easy-make sure you shut the electricity off at the breaker box-having the oven control off does not kill the electricty to the element . Removed the screws, pull out the element, disconnected two wires, re-attach to the new element, install the screws.
Was this helpful?
Thank you for voting!
Heating element in bottom oven burned out
0 of 1 people
found this instruction helpful.
-
Jim from Arvada, CO
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
First I made sure I turned off the breakers in the circuit box that controlled the circuits for the ovens . Then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. The factory wrapped a large amount of tape around the connection between the wires and the he
... Read more
ating element. That took a while to get off. And I searched for heat-resistant electric tape to replace it (because, it must have served some purpose if they had it on originally). The wires hooked onto the spade connectors for the new elements with no problem. I pushed them back into the hole in the back of the oven, replaced the screws, turned the breakers back on, and it worked great from there on.
Read less
Was this helpful?
Thank you for voting!
element burned out
0 of 2 people
found this instruction helpful.
-
Edward from Colville, WA
- Really Easy
- 15 - 30 mins
-
Nutdriver
removed and replaced
Was this helpful?
Thank you for voting!
Heating element melted down
-
Dean from Decatur, IL
- Really Easy
- Less than 15 mins
-
Nutdriver
Shut off power at breaker. Removed two retaining screws, slid out element and unplugged wires, replaced heating element in reverse order. Turned power on and job was complete.
Was this helpful?
Thank you for voting!
Burned out broiler element
-
joseph from Stockton, CA
- Really Easy
- Less than 15 mins
-
Socket set
After getting the part from PartSelect, which only took 2 days to get here and was in great condition and matched perfectly. I went to the customers house, shut off the power to the oven, removed the 2 screws holding in the element, pulled the element out and removed the leads. Took the new element and put the leads on the contacts, pus
... Read more
hed the wires and leads back into the hole and screwed in the 2 screws. Went outside and turned the breaker back on, went and turned the oven on to broil, waited a few seconds and it heated up perfectly, and the customer was real happy. She said it was great that she could bake again. Thank you guys for sending the right part in a timely manner and good condition, it keeps my customers happy and keeps me in business. Joe
Read less
Was this helpful?
Thank you for voting!
element was bad, not heating
-
DANNY from GROVE CITY, OH
- Really Easy
- Less than 15 mins
-
Socket set
had two screws to remove from old element, than removed two electric wires from the old element and put the new element back in by putting the wires on the new element and reinstalling the element back in place with two screws and it was done. took about 5 mins. to complete. easy.
Was this helpful?
Thank you for voting!
Clips needed to re attach heating element
-
Dennis from Orlando, FL
- Really Easy
- Less than 15 mins
-
Pliers
Pulled out old with pliers. Twisted new clips in per instructions.
Was this helpful?
Thank you for voting!
Broiler element would not heat
-
George from Fairport, NY
- Really Easy
- 15 - 30 mins
-
Socket set
After turning off power, I removed the two screws and pulled the element and wires out, removed the wires and then attached them to the new element and replaced the screws. However, this did NOT correct the problem. The broiler did not work until I tried several times turning it on and off. It then worked once but then did not. It worke
... Read more
d once more after several tries. I then called a repairman suspecting the control board. He confirmed this and tested the old element which was in good working order after all. A new board has been ordered.
Read less
Was this helpful?
Thank you for voting!
heating element for the oven broke in two
-
delbert from lewisville, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
ordered part came in noticed i had to make ajustments to new heating element took socket set and unscrewed four screws put a retainer on the wires that came out of the wall to make sure they didn't go back into the wall and would be unretrieveable. installed new screws and cover plate and turned on the oven all done works perfectly.
Was this helpful?
Thank you for voting!
Broiler element
-
Jess from Edmond, OK
- Very Difficult
- 15 - 30 mins
-
Nutdriver, Pliers
I tried to unplug old element without success. Called appliance repair man and he pulled part way out, took hold of place where plugged in with pliers and unplugged. While holding back part of plug he plugged in new element--$60.00 later.
Was this helpful?
Thank you for voting!
Replace Broiler Element
-
Mike from Davisburg, MI
- Easy
- 15 - 30 mins
-
Socket set
The whole job took about 20 min. TURN POWER OFF AT CIRCUIT BREAKER!! Remove 4 screws from the convection cover, then 2 more holding in the broiler element, disconnect 2 wires, and connect to the new one. put the screws back in, the cover back on the convection element and you are done!
Was this helpful?
Thank you for voting!