My Orders
- Home
- JCBP85SJ2SS
- Instructions
JCBP85SJ2SS General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
bake element burned out.
6 of 6 people
found this instruction helpful.
-
harold from spearman, TX
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers
Turn off power to oven,remove two screws holding element in place,pull element forward approx. 1" and unplug wires,remove element. Install new element in reverse order of above.
Was this helpful?
Thank you for voting!
Bake element broke into pieces
6 of 6 people
found this instruction helpful.
-
Rita from LYMAN, SC
- Very Easy
- Less than 15 mins
-
Nutdriver
Disconnect electric at panel box. Pull oven out. Remove 5 screws from rear panel. Pull off the 2 clips at the tips of the old element which is located about 2/3 down the back side of the oven. Remove broken element from inside the oven and slide new element in place. Push 2 clips firmly on the ends of the new element. Replace back co
... Read more
ver. Turn power on. Test oven. Slide oven back in place.
Read less
Was this helpful?
Thank you for voting!
F2 error; over heating, unknown reason
6 of 6 people
found this instruction helpful.
-
Tim from LEAVENWORTH, WA
- Very Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I just followed the instructions on the link provided with the part
Was this helpful?
Thank you for voting!
switch went to high setting no matter what the setting was
10 of 19 people
found this instruction helpful.
-
Frank from Glen Cove, NY
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
took off cover, pulled all wires off switch, pushed wires on new switch, put cover back on. Whalaa..
Was this helpful?
Thank you for voting!
Old coil burned out
5 of 5 people
found this instruction helpful.
-
Matthew from Cynthiana, KY
- Easy
- 15 - 30 mins
-
Nutdriver
After reading all the repair stories I knew that their wasn't any extra wire when the old element is removed. Well, even with that knowlage one of the wires came loose and slipped back in. Fortunately I was able to remove a panel in back and push it back through. I was afraid I would have to take off the whole back but instead there is a
... Read more
panel covering the wire running down the center of the oven. After removing 5 screws with the same nut driver as the one for the coils I had it done in minutes. I had no problem and I am NOT a 'do it yourselfer'. Oh, did I mention I ordered the part on Friday and received it on Saturday standard shipping? Pays to live the next state over from the place shipping it.
Read less
Was this helpful?
Thank you for voting!
Red Light On
5 of 5 people
found this instruction helpful.
-
Lawrence from DECATUR, AL
- Really Easy
- 30 - 60 mins
Red Light Off
Was this helpful?
Thank you for voting!
The small burner inside the double burner shortd out.
5 of 5 people
found this instruction helpful.
-
david from PORT ORANGE, FL
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
The first thing was to watch U-Tube . The replacement burner was being
replaced in a GE glass top range. Exter tools were required than depicted
in the U-Tube project. The project overall was not dificult for me however I was a general contracter for over 25 years
replaced in a GE glass top range. Exter tools were required than depicted
in the U-Tube project. The project overall was not dificult for me however I was a general contracter for over 25 years
Was this helpful?
Thank you for voting!
Baking element cut on fire
5 of 5 people
found this instruction helpful.
-
Hedayat from LONGWOOD, FL
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers
In this case I had to pull the range out to disconnect the power and also to remove the plate covering the electrical connectors. This was the only way to reconnect the elements terminals since the wires were too short to do it inside the oven. Undo the 2 screws holding the element in place from inside the oven to remove and install the n
... Read more
ew one before connecting the terminals from the back. Put back the rear cover and reconnect the power.
Read less
Was this helpful?
Thank you for voting!
Outer ring of burner did not work
5 of 5 people
found this instruction helpful.
-
Barry from Bradenton, FL
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers, Socket set
1- opened oven door
2- unscrewed 2 screws underneath top with a socket wrench
3- unscrewed clips that held burner
4-used needle nose pliers to pull off wire clips off old burner
5- placed wires onto new burner
6- opened clips to make it easier to reinsert burner
7-reattached burner
8-Replaced top
... Read more r />The hardest part was unscrewing the 2 screws that held the top in place due to the position of the screws
2- unscrewed 2 screws underneath top with a socket wrench
3- unscrewed clips that held burner
4-used needle nose pliers to pull off wire clips off old burner
5- placed wires onto new burner
6- opened clips to make it easier to reinsert burner
7-reattached burner
8-Replaced top
... Read more r />The hardest part was unscrewing the 2 screws that held the top in place due to the position of the screws
Read less
Was this helpful?
Thank you for voting!
Oven in accurate temp too low.
6 of 8 people
found this instruction helpful.
-
Joseph from LIBERTY HILL, TX
- Really Easy
- Less than 15 mins
-
Nutdriver
Open the oven , remove one screw holding the sensor remove the sensor and replace the sensor.
Was this helpful?
Thank you for voting!
When inspecting the back of my oven I noticed the cable had been pushed under (my guess from the mouse I found electrocuted where the power lines come in) and was touching one of the element prongs which burned the covering.
6 of 8 people
found this instruction helpful.
-
Mary from Bolton, MA
- Really Easy
- Less than 15 mins
-
Socket set
Not counting unplugging it and taking off the 3 back panels of the oven (< 5 min.) It took < 2min. to change out. Unclipped cable in back, unscrewed one screw inside of oven at top between the two elements and pulled cable through to front, reversed to attach new sensor. Buttoned up the back, plugged back in and was good to go.
Was this helpful?
Thank you for voting!
Burned out oven element
6 of 9 people
found this instruction helpful.
-
Jeremy from Savoy, IL
- Really Easy
- Less than 15 mins
-
Socket set
I unscrewed and removed the old element from inside the oven, but unfortunately there wasn't enough extra wire to pull through and attach the new element from the front, so I had to move the oven away from the wall, remove the back panel, and connect the new element from the rear. Very self-explanatory.
The new element had som ... Read more e kind of spray or coating on it that caused some smoke for a few minutes, but then it worked fine.
The new element had som ... Read more e kind of spray or coating on it that caused some smoke for a few minutes, but then it worked fine.
Read less
Was this helpful?
Thank you for voting!
GE oven showed "F2" error code and was over-heating
5 of 6 people
found this instruction helpful.
-
Kyle from AURORA, CO
- Really Easy
- 30 - 60 mins
-
Nutdriver
I am not the handiest person in the world, and this repair was easy even for me. If you suspect that the temperature sensor is the problem, do yourself a favor and buy this inexpensive replacement part and install it yourself prior to calling a professional who will charge a service fee just for checking it out. Pull your oven out from
... Read more
the wall so you can access the back. Unscrew the small nuts on the back to remove the sheet metal cover. Find the wire that goes to the sensor and unplug the plastic coupling. In the oven, unscrew the one nut that secures the sensor to the back wall of the oven. Pull the broken sensor out and replace it with the new sensor. Feed the wire through to the back and plug the new sensor into the same wire that was just disconnected. Reinstall all of the nuts. Do a "test cook" on some frozen food to ensure that the temperature seems correct (i.e., does it cook as expected in the recommended amount of time). The actual repair takes less than five minutes. I put "30-60 minutes" to account for unplugging the oven, pulling it out, removing the screws, replacing the screws, pushing it back in, and testing the temperature.
Read less
Was this helpful?
Thank you for voting!
surface burner switch was burned
5 of 6 people
found this instruction helpful.
-
abbas from redmond, WA
- Really Easy
- More than 2 hours
-
Nutdriver, Screw drivers
After receiving the new swith from part select in less than four days with surface mail as they promised, it took me less than five minutes to replace the new swith with the old one. The only tools that I needed were A) a 5/16 nut driver to remove the back panel in order to get an access to the swith.B) a phillips screw driver to remove t
... Read more
he swith assembley from the front panel.
I had an estimate from a technician to do the job for 196.27 dollars!!!!!:(:(. I only paid 29.56 Dollars to part select to get this swith, including the shipping.:):):)
I had an estimate from a technician to do the job for 196.27 dollars!!!!!:(:(. I only paid 29.56 Dollars to part select to get this swith, including the shipping.:):):)
Read less
Was this helpful?
Thank you for voting!
F2 Error on Display
4 of 4 people
found this instruction helpful.
-
Tom from FORNEY, TX
- Very Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
The repair was very easy to do. Our oven was showing the F2 error code, which is associated with an over-temperature fault. Upon inspection, the oven was warm, but definitely not beyond the temperature threshold. I researched the issue and found this temperature sensor.
Swapping the sensor was extremely easy. You take off the back pa ... Read more nel of the oven, unhook a single wiring harness, and undo some bolts inside the oven, which allows you to pull off the old sensor. Simply hook up the new sensor to the harness, pull everything back through, replace the fasteners, and you're good to go.
Swapping the sensor was extremely easy. You take off the back pa ... Read more nel of the oven, unhook a single wiring harness, and undo some bolts inside the oven, which allows you to pull off the old sensor. Simply hook up the new sensor to the harness, pull everything back through, replace the fasteners, and you're good to go.
Read less
Was this helpful?
Thank you for voting!