EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

JCBP83SK2SS General Electric Range - Instructions

All Instructions for the JCBP83SK2SS
106 - 120 of 431

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
drwer slide under stove broke off.
3 of 4 people found this instruction helpful.
  • paul from sewell, NJ
  • Really Easy
  • Less than 15 mins
  • Screw drivers
recieved part the next day. looked different but I followed instructions and the part worked perfect.
Was this helpful?
Thank you for voting!
The temperature indicator light on the oven was broken.
3 of 4 people found this instruction helpful.
  • Jewel from Nacogdoches, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I removed the control panel by removing 7 screws and replaced the light indicator and lens.
Was this helpful?
Thank you for voting!
Burner Was Not Working
3 of 4 people found this instruction helpful.
  • Roland from Miami, FL
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Removed the two screws that hold the range top down. Lifted up yhe range top and propped with a stick. Proceeded to mark the wires connected to the old burner so that the new one would be connected correctly. Removed the wires and then the two brackets that hold the burner in place. Removed the old burner and installed the new one. C onnected the wires and resecured top to base. Turned on the current and it worked beautifully.
Was this helpful?
Thank you for voting!
burner not work
3 of 4 people found this instruction helpful.
  • SILVIA from Midlothian, TX
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Fue muy facil desconectar primero la estufa despues quite los tornillos de la parte superior detras de la estufa, desconecte un cable del switch y lo conecte en el nuevo despues el siguiente hasta conectar todos los cables en el nuevo switch. Lo mejor es desconectar uno por uno para mo mesclar los cables , despues removi el switch de la e stufa y puse el nuevo , puse las partes de regreso y listo conecte la estufa t revise si funcionava el quemador y listo sin ningun problema.
Was this helpful?
Thank you for voting!
Outer burner was not working
2 of 2 people found this instruction helpful.
  • Kevin from Leominster, MA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Very simple repair. Remove two screws to lift the range top. Then remove the two screws holding the element in place. Disconnect the wires from the old element, connect the wires to the new element. Reverse the procedure and you are done. Total time is anywhere from 15 to 30 minutes.
Was this helpful?
Thank you for voting!
Element would not respond to changes in temperature setting
3 of 5 people found this instruction helpful.
  • douglas from chance, VA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Turn off power to cook top. Remove 2 screws that hold the cook top to countertop. Lift complete cook top from counter and place diagonally across opening. Remove 10 screws that hold glass top to the component cabinet. Make a diagram of wiring to element. Disconnect wires. Remove 2 mounting brackets from bottom of old element and posi tion them on new element and screw tight. Wire new element as diagrammed earlier. Replace glass top on component cabinet and reinstall 10 screws. Place unit back into counter opening and secure with 2 straps. Turn power back on. Stand back and enjoy your accomplishment.
Was this helpful?
Thank you for voting!
The indicator light stopped working
3 of 5 people found this instruction helpful.
  • Charles from Damascus, MD
  • Easy
  • 15 - 30 mins
  • Wrench (Adjustable)
I knew the lens (which also holds the light) was broken. I also ordered the light. I flipped the circuit breaker, raised the stove top and removed the 6 nut-head screws holding the cover plate. A nut driver would have been helpful, but I got by with a 6" crescent wrench. I removed the cover. I unplugged the two wires from the old light an d plugged in the new one. I inserted the new lens and slipped the light over it. I flipped the circuit breaker on to make sure it worked. After flipping the circuit breaker off, I replaced the cover plates and the screws and lowered the stove top. I flipped the circuit breaker on. It worked!
Was this helpful?
Thank you for voting!
front lift burner not working and surface light on with everything off
2 of 2 people found this instruction helpful.
  • kevin from GAYLORD, MI
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
unplugged the range removed 4 screws from back top cover then took the knob off controller removed 2 screws from behind the knob removed 1 wirer at a time and placed it on the new controller in same order the wires came off put everything back to gather did not fix the problem .
Was this helpful?
Thank you for voting!
Defective switch
2 of 2 people found this instruction helpful.
  • Mary from EDENTON, NC
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Replaced element control switches
Was this helpful?
Thank you for voting!
Stove overheated with an F2 error
2 of 2 people found this instruction helpful.
  • Richard from PHOENIX, AZ
  • Easy
  • 15 - 30 mins
  • Nutdriver
Removed screws holding temp sensor, pulled wire out from behind wall until found connector, disconnected old sensor.
Measured resistance of old sensor and compared with new sensor, they measured nearly the same. Installed the new sensor and tested the stove. Came up to temp ok. No problem since, about 2 weeks.
Was this helpful?
Thank you for voting!
Just didn't work no pwr to it
2 of 2 people found this instruction helpful.
  • Jerry from HOPEWELL, VA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Killed braker first, removed four screws from back, then unplugged all the wiring, then removed four screw that hold the unit on stove, pealed off the face decal, put that on the new on and just reversed the take off press.
Was this helpful?
Thank you for voting!
Stove was not getting enough power.
2 of 2 people found this instruction helpful.
  • Nathan from Wells, ME
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
My stove didn't seem to be getting enough power for the oven to heat up and the burners to get hot enough. When I checked the connection of the electric cord I found that one of the 3 terminals that the plug connects to was broken off. When the new part came I removed the old part by first disconnecting the 3 wires [black,white(ground),r ed] and then using a small but long 1/4 socket (that I found at Lowes)I removed the 2 screws that held the old part to the stove and the green screw under it holding the flat copper piece that also connects under the white ground wire of the part. I mounted the new piece on with the 2 1/4 screws. The new part comes with a piece of copper that is for grounding the part to the stove. When I compared it to the old part it was a little different. I first screwed the copper piece onto the stove (under the part) with the green screw then I screwed the white wire over the copper piece to the center terminal(you have to make the hole of the copper piece line up to the screw hole). I connected the other 2 wires and then connected the electric cord to the new terminal block and then put the back cover back on the stove and plugged it in. The clock came on I turned on the four burners they all got hot and red. I turned on the oven the element on the bottom got red I then turned on the broiler the top element got red. My stove is fixed.
Was this helpful?
Thank you for voting!
the small burner was burnt out
2 of 2 people found this instruction helpful.
  • Jack from Columbiaville, MI
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
after removing the two screws that are just inside the oven, I propted the top open with the box that the part came in. I drew and labeled the wires as I took them off using a color coding. next I removed the two clips that held the burner in place and marked on the new burner exactly where the clips were attached. Replacing the clips was possibly the hardest part of the whole operation. When you replace the burner, don't forget to replace the insulation pad that is stuck one the metal where the conections are. I missed this and had to reopen the stovetop and slid it on after I was finished. Otherwise it went pretty smooth.
Was this helpful?
Thank you for voting!
Bake element shattered while cooking coating everything inside with a fine white dust
2 of 2 people found this instruction helpful.
  • Greg from Virginia Beach, VA
  • Easy
  • 15 - 30 mins
  • Screw drivers, Wrench set
First I searched for the part here and I had a slightly hard time finding the correct element on the site.
Then I read the comments of the others and the issues they faced.
I unplugged the range and pulled it out a bit from the wall. I then removed the two screws that hold the element in place and put them where I would not lose them. Then I gently maneuved the element out and placed a clothespin on each of the wires to keep them from going back in and then disconnected the wires from the element using a pair of needlenose pliers.

At this point I had to gently bend the new element back into shape as it had been bent during shipping. Then I connected the wires and slid the element into place and installed the two screws.

Double checked to make sure everything was ok plugged in the range, said a quick prayer and set the temperature to 300. When it got to 300 the element shut off and I was happy that the element did not take any other parts with it.
Was this helpful?
Thank you for voting!
Electrode burnt off on left side
2 of 2 people found this instruction helpful.
  • Kenneth from Wisconsin Rapids, WI
  • Easy
  • 15 - 30 mins
  • Nutdriver
First I removed the five screws that hold the
element in place and pulled the element out
about 3 inches and disconnected the two wires
and hooked a piece of wire on the leads to make sure they did not fall behind the cabinet.
Then I connected the new element to the lead
wires and removed the piece of wire and secured the new element in place with the mounting screws. Took about 25 minutes to remove and replace.
Was this helpful?
Thank you for voting!
All Instructions for the JCBP83SK2SS
106 - 120 of 431