EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

JCBP81DM1BB General Electric Range - Instructions

All Instructions for the JCBP81DM1BB
46 - 60 of 151

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Broker inner glass
4 of 5 people found this instruction helpful.
  • marc from PARK RIDGE, NJ
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Very easy to remove the parts and to reassemble
Was this helpful?
Thank you for voting!
oven would not heat
5 of 8 people found this instruction helpful.
  • Jim from Williamsburg, VA
  • Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
I removed the 4 hex head screws holding the control panel , then the other 4 slotted screws. Disconnected all wires being careful to keep track of the color coding. Had a little trouble with the adhesive holding the face plate( I don't know why they even used it). Put the new panel in and reconnected it. Re set circuit breaker and tried t he oven. It still wouldn't heat. it wasn't the control panel, but a burned out wire connecting the element in the back of the oven. Well, anyway I learned how to do the job and the the new panel activates better, so all was not lost.
Was this helpful?
Thank you for voting!
Inner glass assembly had cracked
3 of 3 people found this instruction helpful.
  • Richard from Gorham, ME
  • Really Easy
  • 30 - 60 mins
  • Socket set, Wrench set
Took the oven door off and removed the inner door panel, put new glass assembly part in and reassembled. The hard part was getting the door hinges locked back into place.
Was this helpful?
Thank you for voting!
blew out board by crossing wires..mistakenly toke out bulb assembly to replace bad bulb
3 of 3 people found this instruction helpful.
  • Ken from CALABASH, NC
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Turne off power to range..pulled oven out..Took top back panel off with nut driver. 4screws .. Took picture of control board....removed bad control board with Phillips driver...4 screws....installed New board...removed 1 connection at a time and replaced in New board..Turned power on to test new board...check picture to make sure connect ions are correct...turn off power...put back panel back on...put range back in place...turn power back o n...done ..approximate time 15 to 20 minutes..
Was this helpful?
Thank you for voting!
Small front burner on our glass top stove died.
3 of 3 people found this instruction helpful.
  • Robert from FLEMING ISLE, FL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Robert did not do the repairs. I did! 70 year old housewife. I watched a Utube video and thought I could certainly handle that. Ordered my part from your site. It came in two days. Burnet was replaced in under 20 minutes by me! Anyone can do this. Super easy, parts just plug in.
Was this helpful?
Thank you for voting!
OVEN CLOCK CONTROL MALFUNCTIONED
3 of 3 people found this instruction helpful.
  • Gregoire from N CHESTERFLD, VA
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Wrench set
I turned off the circuit breaker and unplugged the stove. I removed the back panel and marked the location of the wires on the new oven clock control. I detached the wires and removed the old card. I installed the new one and reconnected the wires. I plugged the stove and turned on the circuit breaker. All the lights came on and the oven worked fine. I reinstalled the back panel and it took me less than thirty minutes to complete the job.
Was this helpful?
Thank you for voting!
Needed to replace oven door gasket
3 of 3 people found this instruction helpful.
  • Jayne from EAST PEORIA, IL
  • Very Easy
  • 15 - 30 mins
  • Screw drivers
Watched youtube video. Very easy to replace
Was this helpful?
Thank you for voting!
Incorrect oven temperature due to defective temperature sensor.
3 of 3 people found this instruction helpful.
  • Anthony from FARMINGVILLE, NY
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Performed repair using a video for reference.
Was this helpful?
Thank you for voting!
Hole in gasket
3 of 3 people found this instruction helpful.
  • Cynthia from Kidder, MO
  • Very Easy
  • Less than 15 mins
I took the oven door off. Laid it down on a blanket on the floor. I pulled up on end going into the door, then went around with fingers to feel where the clip were and grab the clip with my fingers and gently pulled up. Then grabbed the new gasket, found the center clip that goes at top of door and started pushing the clips in. The last w as feeding the ends back into the slot in the door.
Was this helpful?
Thank you for voting!
When you touched any button on the controls LOC on appeared.
3 of 3 people found this instruction helpful.
  • Roger from HUNTSVILLE, AL
  • Very Easy
  • Less than 15 mins
Talked to parts select tech after ordering the control board. Tech advised me that he felt the range could be repaired without installing any parts. Advised me to contact manufacture tech support and explain the problem. I did to find that the child safety lock was on, probably from cleaning and touching too many buttons at once while whi pping surface. Told me to hold down + and - at the same time for three seconds and it was fixed.
Parts select tech had told me don’t worry the parts are guaranteed so I called for a RMA and returned the parts for a refund. Thanks Parts Select, y’all are real professionals and that is greatly appreciated.
Thank you all.
Was this helpful?
Thank you for voting!
The temperature indicator light on the oven was broken.
3 of 4 people found this instruction helpful.
  • Jewel from Nacogdoches, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I removed the control panel by removing 7 screws and replaced the light indicator and lens.
Was this helpful?
Thank you for voting!
Replace Thermostat
2 of 2 people found this instruction helpful.
  • Russell from Morgantown, WV
  • Really Easy
  • Less than 15 mins
  • Socket set
Pull oven out away from the wall, unplugged from outlet, removed center cover by removing 5 sheet metal screws. disconnected thermostat sensor from control cable. Opened oven door and removed screw that holds thermostat sensor. Pulled thermostat sensor out replaced with new sensor. Plugged sensor in to control cable. Replace panel and scr ews. Then my wife made me clean the oven. I recommend making the repair when your wife is not home.
Was this helpful?
Thank you for voting!
Burner remained on "high" as contacts were fused together
2 of 2 people found this instruction helpful.
  • Bruce from HOLMEN, WI
  • Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Easy removal of switch and installation of new switch block.
Was this helpful?
Thank you for voting!
lights blown out
6 of 14 people found this instruction helpful.
  • Gerald from WINTERVILLE, GA
  • Very Easy
  • Less than 15 mins
replaced lights in refrigirator and freezer
Was this helpful?
Thank you for voting!
Stove was not getting enough power.
2 of 2 people found this instruction helpful.
  • Nathan from Wells, ME
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
My stove didn't seem to be getting enough power for the oven to heat up and the burners to get hot enough. When I checked the connection of the electric cord I found that one of the 3 terminals that the plug connects to was broken off. When the new part came I removed the old part by first disconnecting the 3 wires [black,white(ground),r ed] and then using a small but long 1/4 socket (that I found at Lowes)I removed the 2 screws that held the old part to the stove and the green screw under it holding the flat copper piece that also connects under the white ground wire of the part. I mounted the new piece on with the 2 1/4 screws. The new part comes with a piece of copper that is for grounding the part to the stove. When I compared it to the old part it was a little different. I first screwed the copper piece onto the stove (under the part) with the green screw then I screwed the white wire over the copper piece to the center terminal(you have to make the hole of the copper piece line up to the screw hole). I connected the other 2 wires and then connected the electric cord to the new terminal block and then put the back cover back on the stove and plugged it in. The clock came on I turned on the four burners they all got hot and red. I turned on the oven the element on the bottom got red I then turned on the broiler the top element got red. My stove is fixed.
Was this helpful?
Thank you for voting!
All Instructions for the JCBP81DM1BB
46 - 60 of 151