Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
BASE OF BULB BROKE OFF & WELDED TO SOCKET
1 personfound this instruction helpful.
NEIL from ROCKY POINT, NY
Easy
30 - 60 mins
Nutdriver, Pliers
PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.
Was this helpful?
Thank you for voting!
Oven door gasket was damaged and leaking
1 personfound this instruction helpful.
Kerry from Sheboygan, WI
A Bit Difficult
1- 2 hours
Socket set
I watched the repair video on YouTube and followed his instructions as much as possible. Went pretty well as I thought it would be harder. I’m pretty handy so, I was pleased.
Was this helpful?
Thank you for voting!
Change bulb
3 of 8 peoplefound this instruction helpful.
Louis from LEAGUE CITY, TX
Really Easy
30 - 60 mins
Nutdriver
Easy
Was this helpful?
Thank you for voting!
dropped & broke the oven light bulb cover
1 of 2 peoplefound this instruction helpful.
joseph from san jose, CA
Really Easy
Less than 15 mins
popped the new one on!
Was this helpful?
Thank you for voting!
Knob stem broke off.
1 of 2 peoplefound this instruction helpful.
DALE from FREMONT, NE
Very Easy
Less than 15 mins
Nutdriver, Pliers, Screw drivers
Pulled stove out to access back panel. Unscrew broken switch/stem. Replaced each wire one at a time to make sure they went in right spot. Screw in new switch. Replaced back panel.
Was this helpful?
Thank you for voting!
Water dumped over in in my overhead microwave, which dripped down on, & shorted out a burner switch.
1 of 3 peoplefound this instruction helpful.
Deanna from Buckeye, AZ
Really Easy
Less than 15 mins
Pliers, Screw drivers
My husband had already removed the back plate form the stove and detached the wires from the old burner switch because it was keeping the burner on. He unscrewed the old switch and removed it. He then popped in the new switch, attached the wires to the correct contacts, and put the back plate back on. We plugged in the stove, and that
... Read moreburner works good as new.
Read less
Was this helpful?
Thank you for voting!
Heating element burned out
1 of 3 peoplefound this instruction helpful.
William from CONCORD, MA
Very Easy
30 - 60 mins
Pliers, Screw drivers
Followed example on YouTube! Very easy.
Was this helpful?
Thank you for voting!
Burner not heating.
1 of 5 peoplefound this instruction helpful.
Jack from Greensboro, GA
Really Easy
30 - 60 mins
Screw drivers
Isolated to control switch.
Replaced
Was this helpful?
Thank you for voting!
light keep burning out in oven.
2 of 8 peoplefound this instruction helpful.
john from Mc Kees Rocks, PA
Really Easy
30 - 60 mins
Nutdriver
Remove the door. Just open a little and pull up. Removed racks. Removed 3 screws with nutdriver. Pulled out housing. Disconnected 2 wires. Assembled new housing with with bulb receptacle and gasket. Reconnected wires and crimped a little to make them snug. Pushed housing back into hole. Put 3 screws back in, inserted bulb and cover. Slid
... Read moredoor back on and done. 30 minutes at most.
verified switch operation , checked continuity of burner element found open ordered new part and installed next day after extremely fast service from partselect thank you
Was this helpful?
Thank you for voting!
Light burnt out.
2 of 8 peoplefound this instruction helpful.
Roscoe G from ROCHESTER, NY
Very Easy
Less than 15 mins
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this helpful?
Thank you for voting!
eye wouldnt come on
0 of 2 peoplefound this instruction helpful.
daniel from valentines, VA
Really Easy
15 - 30 mins
Nutdriver
removed the top section on stove and removed the wires off swtitch and put on new one then put new switch in
Was this helpful?
Thank you for voting!
one burner not working
Edwin from HIGHLANDS RANCH, CO
Really Easy
15 - 30 mins
Socket set
Removed two screws to access burner. Removed three power clips from burner, reattached the clips to new burner, removed brace clips and attach to new burner, close lid and reattach stove cover.
Was this helpful?
Thank you for voting!
Pilot light out
Henry from Sonoita, AZ
Really Easy
15 - 30 mins
Screw drivers, Socket set
Removed the power plug from the wall, screwdriver and small socket allowed me to remove the front control panel. Once I located the pilot light I pulled off the holding clips and placed a new light into the holding clips...problem solved.
Was this helpful?
Thank you for voting!
The middle of the element quit working.
Ruth Ann from New Columbia, PA
Easy
15 - 30 mins
Nutdriver, Screw drivers
Took the old burner out, tranferred the wires from old to new. Installed the new burner. Works fine.
My Orders
