JCBP80CK4CC General Electric Range - Instructions

Removed the two screws that hold the range top down. Lifted up yhe range top and propped with a stick. Proceeded to mark the wires connected to the old burner so that the new one would be connected correctly. Removed the wires and then the two brackets that hold the burner in place. Removed the old burner and installed the new one. C ... Read more onnected the wires and resecured top to base. Turned on the current and it worked beautifully.

1st and formost, unplug the range from the outlet or shut th breaker off (Ranges are on a seperate breaker). Detach 2 wires on the back of the range connected to the element. Remove three nut screws inside the oven holding the old element in place . 1 on the top and 2 at the back of the oven. Now just reverse this procedure to install the ... Read more new element and your all done.

Fue muy facil desconectar primero la estufa despues quite los tornillos de la parte superior detras de la estufa, desconecte un cable del switch y lo conecte en el nuevo despues el siguiente hasta conectar todos los cables en el nuevo switch. Lo mejor es desconectar uno por uno para mo mesclar los cables , despues removi el switch de la e ... Read more stufa y puse el nuevo , puse las partes de regreso y listo conecte la estufa t revise si funcionava el quemador y listo sin ningun problema.

replaced lights in refrigirator and freezer

Killed braker first, removed four screws from back, then unplugged all the wiring, then removed four screw that hold the unit on stove, pealed off the face decal, put that on the new on and just reversed the take off press.

unplugged the range removed 4 screws from back top cover then took the knob off controller removed 2 screws from behind the knob removed 1 wirer at a time and placed it on the new controller in same order the wires came off put everything back to gather did not fix the problem .

I knew the lens (which also holds the light) was broken. I also ordered the light. I flipped the circuit breaker, raised the stove top and removed the 6 nut-head screws holding the cover plate. A nut driver would have been helpful, but I got by with a 6" crescent wrench. I removed the cover. I unplugged the two wires from the old light an ... Read more d plugged in the new one. I inserted the new lens and slipped the light over it. I flipped the circuit breaker on to make sure it worked. After flipping the circuit breaker off, I replaced the cover plates and the screws and lowered the stove top. I flipped the circuit breaker on. It worked!

Turn off power to cook top. Remove 2 screws that hold the cook top to countertop. Lift complete cook top from counter and place diagonally across opening. Remove 10 screws that hold glass top to the component cabinet. Make a diagram of wiring to element. Disconnect wires. Remove 2 mounting brackets from bottom of old element and posi ... Read more tion them on new element and screw tight. Wire new element as diagrammed earlier. Replace glass top on component cabinet and reinstall 10 screws. Place unit back into counter opening and secure with 2 straps. Turn power back on. Stand back and enjoy your accomplishment.

Removed screws holding temp sensor, pulled wire out from behind wall until found connector, disconnected old sensor.
Measured resistance of old sensor and compared with new sensor, they measured nearly the same. Installed the new sensor and tested the stove. Came up to temp ok. No problem since, about 2 weeks.

Replaced element control switches

after removing the two screws that are just inside the oven, I propted the top open with the box that the part came in. I drew and labeled the wires as I took them off using a color coding. next I removed the two clips that held the burner in place and marked on the new burner exactly where the clips were attached. Replacing the clips ... Read more was possibly the hardest part of the whole operation. When you replace the burner, don't forget to replace the insulation pad that is stuck one the metal where the conections are. I missed this and had to reopen the stovetop and slid it on after I was finished. Otherwise it went pretty smooth.

First I searched for the part here and I had a slightly hard time finding the correct element on the site.
Then I read the comments of the others and the issues they faced.
I unplugged the range and pulled it out a bit from the wall. I then removed the two screws that hold the element in place and put them where I would not lose ... Read more them. Then I gently maneuved the element out and placed a clothespin on each of the wires to keep them from going back in and then disconnected the wires from the element using a pair of needlenose pliers.

At this point I had to gently bend the new element back into shape as it had been bent during shipping. Then I connected the wires and slid the element into place and installed the two screws.

Double checked to make sure everything was ok plugged in the range, said a quick prayer and set the temperature to 300. When it got to 300 the element shut off and I was happy that the element did not take any other parts with it.

First I removed the five screws that hold the
element in place and pulled the element out
about 3 inches and disconnected the two wires
and hooked a piece of wire on the leads to make sure they did not fall behind the cabinet.
Then I connected the new element to the lead
wires and removed the piece of wire and ... Read more secured the new element in place with the mounting screws. Took about 25 minutes to remove and replace.

Very simple repair. Remove two screws to lift the range top. Then remove the two screws holding the element in place. Disconnect the wires from the old element, connect the wires to the new element. Reverse the procedure and you are done. Total time is anywhere from 15 to 30 minutes.

First I removed the oven drawer. Verified that the support clips would rest correctly on rail, then review installation document with supports to locate alternate location for replacement supports. I did have to personally locate 2 fastners not provided with the supports ot complete installation. After installation, oven drawer opens a ... Read more nd closes smoothly.