JCBP79SM1SS General Electric Range - Instructions

opened oven door and removed two 1/4 " screws from range top. lifted range top and propped open like a car hood with a 1" diam dowel rod. marked on new element the wire color locations from old element and removed wires. removed the two small screws and clips that hold the element to the range top and removed element. Matched where the ... Read more mounting screws locate to the new element. Installed new element in reverse order.

Take off 6 screws of back cover of the range, unplug the white wire. Go to the inside of oven, pull out racks. At the top of the oven is your Broiler element, in the center you will see a rod sticking out with one screw holding it in place. Take out screw and pull temperature sensor out toward you. Reverse steps to put it back together.

Pulled stove out to access back panel. Unscrew broken switch/stem. Replaced each wire one at a time to make sure they went in right spot. Screw in new switch. Replaced back panel.

I ordered a new burner assuming As is turns out: nothing wrong with the burner.

turn off the power at the breaker first

remove the 2 screws under the 'lip' of the stove top (open the oven door to get to them)

prop up the stove top on the cardboard box the part came in

pull off the wires one by one and attach to the new burner OR record where each wire goes first

remove the ... Read more old burner (2 screws) and attach the new burner

screw down the stove top

try the burner - when it does not work flip the power breaker back on and then try again

bask in the joy, admiration and wonder directed your way by various family members

popped the new one on!

Pull range away from back wall. Remove panel behind control knobs by removing the screws that hold it on. Find hot burner light that holds lens. Remove broken part of lens. Insert new lens into hole on front of control panel and into hot burner light receptacle. Replace back panel. Slide range back into place.

Use a 1/4" nutdriver and remove the screws that are on the bottom corners of the range top.Prop up the range top high enough for ease of using 1/4" nut driver. Take a picture of the wiring for future reference on re-installing wiring. Note arrow location on burner and remove 1/4" screws holding the clamps to the burner in place and place ... Read more to the side for re-install on new burner.Remove wiring off old burner.Hold new burner in place with arrow location in previous location and notice holes where clamps will go. Screw clamps on burner using original screws and snap in mounting slots on stove.Re-install wiring.Lower range top and re install 2 screws , 1 in each corner under range top. Test for proper operation and enjoy!

Easy

The unit has two spring clips that hold it in place. Also two screws that hold the element to the clips. It comes apart ok but doesn't go back as easy. I didn't remove the top as there was room to work from under it.

My daughter held the top down against a wooden dowl i was using as a prop rod . My wife held the unit in pla ... Read more ce . I finally got the clips back on and the screws back in . Centered the unit , transfered the wires , and it works perfect . Only three people and 30 min.

Thank you PartSelect for all your help !!

As many people have encountered, my oven would not heat but the igniter would be bright orange and glow! Over time, the igniter wears and degrades causing oxidation to the surface. This cause the igniter to fail and operate at a lower current level, below 2.8 amps! Normal igniters operator over 3.0 to 3.1 amps. When is happens, a low c ... Read more urrent igniter does not have enough input to the control valve to tell the valve to open to allow gas to flow over the igniter to light the oven, thus heat the oven! This has got to be the NUMBER one reason for an oven not heating!

Dear PartSelect:

I am very impressed by your service and company. My order arrived in less than 24 hours. It was a perfect match and is currently in service. I am very satisfied with the entire experience and will use your company again.

I simply opened up the cooktop with a screwdriver and disconnected the wire ... Read more s to the affected burner. After the part arrived, I reconnected them. I had to swap over two brackets from the old burner, so don't throw it away until the new one arrives. It went back together very easily and worked immediately.

Matt Brennan

Locate breaker box and turn off breaker to stove. Removed the two screw in front that hold the top in place. Raised the top and supported it with the box the new burner came in. Removed two screws that held the burner in place and the 5 wires one at a time an installed them on the new burner. Put new burner in place and installed two ... Read more mounting screws. Reinstalled the two screws in the front to hold the top in place then turned the breaker back on and tested burner. Worked great. Received part in 2 days.

Unplugged oven, turned off breaker, took cover off back of oven, removed old sensor by disconnecting in back of oven and undoing screw inside oven. Pulled old one out replaced with new took 15min. Cost me less than $20. Parts Select rocks! Even received part in two days with standard shipping!

Once I opened up the back of the range, the sensor wires where there and burnt just like your info said. One nut to take off in the oven and the sensor came right out and the new one went right in. The oven works great, cooked the turkey today. The worst part of the repare was the cleaning behind and under the range, it hasn't moved since ... Read more it was put in 6 years ago. Very pleased with PS.