- Home
- JCBP78WK2WW
- Instructions
JCBP78WK2WW General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven would not heat up
3 of 3 people
found this instruction helpful.
-
Myron from SCOTTSDALE, AZ
- Very Easy
- 15 - 30 mins
-
Socket set
Changed the lower heating element. Simple, simple, simple. I first went on YouTube and watched a couple of videos. Reassurance is a good thing. Okay here we go. 1) Pull the oven out from the wall 2) UNPLUG 3) remove the racks in the oven 4) Unscrew the (2) screws holding the element to the back wall of the oven. 5) There are t
... Read more
wo (2) connections that you simply pull off. Remove the element. 6) Throw the old heating element away and connect the NEW element where the OLD one was. 7) Put the old screws back in. Plug the oven back in and test. VOILA!!! you are now a repairman.
Read less
Was this helpful?
Thank you for voting!
Grease spilled on old gasket----gasket hardened
5 of 9 people
found this instruction helpful.
-
Delores from Rocksprings, TX
- Really Easy
- Less than 15 mins
Simply pulled old gasket from door and pushed new gasket clips into existing holes and tucked in ends at bottom of door.
Was this helpful?
Thank you for voting!
When you touched any button on the controls LOC on appeared.
3 of 3 people
found this instruction helpful.
-
Roger from HUNTSVILLE, AL
- Very Easy
- Less than 15 mins
Talked to parts select tech after ordering the control board. Tech advised me that he felt the range could be repaired without installing any parts. Advised me to contact manufacture tech support and explain the problem. I did to find that the child safety lock was on, probably from cleaning and touching too many buttons at once while whi
... Read more
pping surface. Told me to hold down + and - at the same time for three seconds and it was fixed.
Parts select tech had told me don’t worry the parts are guaranteed so I called for a RMA and returned the parts for a refund. Thanks Parts Select, y’all are real professionals and that is greatly appreciated.
Thank you all.
Parts select tech had told me don’t worry the parts are guaranteed so I called for a RMA and returned the parts for a refund. Thanks Parts Select, y’all are real professionals and that is greatly appreciated.
Thank you all.
Read less
Was this helpful?
Thank you for voting!
Incorrect oven temperature due to defective temperature sensor.
3 of 3 people
found this instruction helpful.
-
Anthony from FARMINGVILLE, NY
- Really Easy
- Less than 15 mins
-
Nutdriver
Performed repair using a video for reference.
Was this helpful?
Thank you for voting!
Switch was not turning off range indicator light
3 of 3 people
found this instruction helpful.
-
Charles from PORTLAND, OR
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Pulled stove out and unplugged. At the rear of the range there were 4 faster. Used a nutdriver piece in an electric drill. Pulled off the cover and located the switch. At the front of the stove, I removed the knob and unscrewed two screws releasing the switch. I undid and replaced each wire connector one-by-one to avoid any wrong connecti
... Read more
ons. Replaced and secured the switch and replace the back panel. All secured, power on and fixed! Easy repair, but something that had been put off for a year!
Also follow the installation videos from PartSelect - very helpful!
Also follow the installation videos from PartSelect - very helpful!
Read less
Was this helpful?
Thank you for voting!
old oven racks were ruined from self-cleaning oven
4 of 6 people
found this instruction helpful.
-
Joan from Holt, MI
- Really Easy
- Less than 15 mins
My exact model number did not appear in the listings, nor were the oven rack measurements clearly stated in items offered. I sent an email to customer service, received an immediate response with the correct answer (re: which part would fit my oven), ordered this item, and had a shipment arrival within days. The racks are a perfect fit,
... Read more
and they look great. The price is less than any other site I investigated.
Read less
Was this helpful?
Thank you for voting!
drwer slide under stove broke off.
3 of 4 people
found this instruction helpful.
-
paul from sewell, NJ
- Really Easy
- Less than 15 mins
-
Screw drivers
recieved part the next day. looked different but I followed instructions and the part worked perfect.
Was this helpful?
Thank you for voting!
The temperature indicator light on the oven was broken.
3 of 4 people
found this instruction helpful.
-
Jewel from Nacogdoches, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
I removed the control panel by removing 7 screws and replaced the light indicator and lens.
Was this helpful?
Thank you for voting!
Burner food on racks
3 of 4 people
found this instruction helpful.
-
John from Metairie, LA
- Really Easy
- Less than 15 mins
Nothing really rocket science here. The oven racks had burned on food, and I just replaced the racks..... slide out the old and slide in the new. Done !
Was this helpful?
Thank you for voting!
Broiler element was bad
3 of 4 people
found this instruction helpful.
-
David from LENOIR CITY, TN
- Easy
- 15 - 30 mins
-
Nutdriver
1st and formost, unplug the range from the outlet or shut th breaker off (Ranges are on a seperate breaker). Detach 2 wires on the back of the range connected to the element. Remove three nut screws inside the oven holding the old element in place . 1 on the top and 2 at the back of the oven. Now just reverse this procedure to install the
... Read more
new element and your all done.
Read less
Was this helpful?
Thank you for voting!
Did not have a problem, just need an extra oven rack.
3 of 4 people
found this instruction helpful.
-
Catherine from Bethel, CT
- Really Easy
- Less than 15 mins
Placing the order was very easy. Shipping was fast and excellent packaging. Thank you very much!
Was this helpful?
Thank you for voting!
burner not work
3 of 4 people
found this instruction helpful.
-
SILVIA from Midlothian, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers
Fue muy facil desconectar primero la estufa despues quite los tornillos de la parte superior detras de la estufa, desconecte un cable del switch y lo conecte en el nuevo despues el siguiente hasta conectar todos los cables en el nuevo switch. Lo mejor es desconectar uno por uno para mo mesclar los cables , despues removi el switch de la e
... Read more
stufa y puse el nuevo , puse las partes de regreso y listo conecte la estufa t revise si funcionava el quemador y listo sin ningun problema.
Read less
Was this helpful?
Thank you for voting!
Burner Was Not Working
3 of 4 people
found this instruction helpful.
-
Roland from Miami, FL
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Removed the two screws that hold the range top down. Lifted up yhe range top and propped with a stick. Proceeded to mark the wires connected to the old burner so that the new one would be connected correctly. Removed the wires and then the two brackets that hold the burner in place. Removed the old burner and installed the new one. C
... Read more
onnected the wires and resecured top to base. Turned on the current and it worked beautifully.
Read less
Was this helpful?
Thank you for voting!
the small burner was burnt out
2 of 2 people
found this instruction helpful.
-
Jack from Columbiaville, MI
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
after removing the two screws that are just inside the oven, I propted the top open with the box that the part came in. I drew and labeled the wires as I took them off using a color coding. next I removed the two clips that held the burner in place and marked on the new burner exactly where the clips were attached. Replacing the clips
... Read more
was possibly the hardest part of the whole operation. When you replace the burner, don't forget to replace the insulation pad that is stuck one the metal where the conections are. I missed this and had to reopen the stovetop and slid it on after I was finished. Otherwise it went pretty smooth.
Read less
Was this helpful?
Thank you for voting!
Bake element shattered while cooking coating everything inside with a fine white dust
2 of 2 people
found this instruction helpful.
-
Greg from Virginia Beach, VA
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
First I searched for the part here and I had a slightly hard time finding the correct element on the site.
Then I read the comments of the others and the issues they faced.
I unplugged the range and pulled it out a bit from the wall. I then removed the two screws that hold the element in place and put them where I would not lose ... Read more them. Then I gently maneuved the element out and placed a clothespin on each of the wires to keep them from going back in and then disconnected the wires from the element using a pair of needlenose pliers.
At this point I had to gently bend the new element back into shape as it had been bent during shipping. Then I connected the wires and slid the element into place and installed the two screws.
Double checked to make sure everything was ok plugged in the range, said a quick prayer and set the temperature to 300. When it got to 300 the element shut off and I was happy that the element did not take any other parts with it.
Then I read the comments of the others and the issues they faced.
I unplugged the range and pulled it out a bit from the wall. I then removed the two screws that hold the element in place and put them where I would not lose ... Read more them. Then I gently maneuved the element out and placed a clothespin on each of the wires to keep them from going back in and then disconnected the wires from the element using a pair of needlenose pliers.
At this point I had to gently bend the new element back into shape as it had been bent during shipping. Then I connected the wires and slid the element into place and installed the two screws.
Double checked to make sure everything was ok plugged in the range, said a quick prayer and set the temperature to 300. When it got to 300 the element shut off and I was happy that the element did not take any other parts with it.
Read less
Was this helpful?
Thank you for voting!