Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Old coil burned out
5 of 5 peoplefound this instruction helpful.
Matthew from Cynthiana, KY
Easy
15 - 30 mins
Nutdriver
After reading all the repair stories I knew that their wasn't any extra wire when the old element is removed. Well, even with that knowlage one of the wires came loose and slipped back in. Fortunately I was able to remove a panel in back and push it back through. I was afraid I would have to take off the whole back but instead there is a
... Read morepanel covering the wire running down the center of the oven. After removing 5 screws with the same nut driver as the one for the coils I had it done in minutes. I had no problem and I am NOT a 'do it yourselfer'. Oh, did I mention I ordered the part on Friday and received it on Saturday standard shipping? Pays to live the next state over from the place shipping it.
Read less
Was this helpful?
Thank you for voting!
Oven in accurate temp too low.
6 of 8 peoplefound this instruction helpful.
Joseph from LIBERTY HILL, TX
Really Easy
Less than 15 mins
Nutdriver
Open the oven , remove one screw holding the sensor remove the sensor and replace the sensor.
Was this helpful?
Thank you for voting!
When inspecting the back of my oven I noticed the cable had been pushed under (my guess from the mouse I found electrocuted where the power lines come in) and was touching one of the element prongs which burned the covering.
6 of 8 peoplefound this instruction helpful.
Mary from Bolton, MA
Really Easy
Less than 15 mins
Socket set
Not counting unplugging it and taking off the 3 back panels of the oven (< 5 min.) It took < 2min. to change out. Unclipped cable in back, unscrewed one screw inside of oven at top between the two elements and pulled cable through to front, reversed to attach new sensor. Buttoned up the back, plugged back in and was good to go.
Was this helpful?
Thank you for voting!
Outer ring of burner did not work
5 of 5 peoplefound this instruction helpful.
Barry from Bradenton, FL
Really Easy
Less than 15 mins
Pliers, Screw drivers, Socket set
1- opened oven door 2- unscrewed 2 screws underneath top with a socket wrench 3- unscrewed clips that held burner 4-used needle nose pliers to pull off wire clips off old burner 5- placed wires onto new burner 6- opened clips to make it easier to reinsert burner 7-reattached burner 8-Replaced top
... Read morer />The hardest part was unscrewing the 2 screws that held the top in place due to the position of the screws
Read less
Was this helpful?
Thank you for voting!
Original terminal block plastic shielding melted, protecting appliance when the wires overheated.
6 of 8 peoplefound this instruction helpful.
Brian from DOVER, PA
Really Easy
30 - 60 mins
Nutdriver
Safety first * Unplugged 220 VAC from outlet. Removed shield cover screws with 1/4" hex nut driver (5 screws). Removed all 6 silver screws from terminal block with 1/4" nut driver, freeing all wires. Removed the green ground screw and ground bracket from center terminal. Cut away (using the drill) melted original terminal block plastic to
... Read more access the 2 black 1/4" nuts holding original terminal block onto appliance. Discarded the original damaged terminal block. Attached the new terminal block, aligning the mounting holes and the terminal block the same way the original terminal block was lined up and re-used the black 1/4" nuts (original used because the replacement package did not include new black screws). I bought a new appliance cord, since the original cord overheated. Reattached all wires using the 6 new silver screws. Start with the middle terminal by attaching the appliance wires and the ground bracket. The ground must be attached to the bracket and the bracket bridges between the terminal block and the range body. Reattached shield cover. Plugged in appliance. Note: it doesn't matter which outside wire attaches to the outside terminals (both are hot), but the middle wire (neutral) must attach to the middle terminal. However, the ring terminal should be flush on the terminal block so you don't bend the ring.
Read less
Was this helpful?
Thank you for voting!
The small burner inside the double burner shortd out.
5 of 5 peoplefound this instruction helpful.
david from PORT ORANGE, FL
Easy
30 - 60 mins
Nutdriver, Pliers, Screw drivers, Socket set
The first thing was to watch U-Tube . The replacement burner was being replaced in a GE glass top range. Exter tools were required than depicted in the U-Tube project. The project overall was not dificult for me however I was a general contracter for over 25 years
Was this helpful?
Thank you for voting!
Glass- top range had two burners that would not regulate. Burners went to HIGH when dial was set on any setting, even low.
5 of 5 peoplefound this instruction helpful.
christopher from WOODSTOCK, GA
Really Easy
30 - 60 mins
Nutdriver, Screw drivers
Replaced switches. Dual power switch had been updated and didn’t match original part but there were accurate instructions in package to allow correct wiring easily. Good job Parts Select.
Wife broke the interior window by splashing water on it while heated to 450.
6 of 8 peoplefound this instruction helpful.
Dennis from GRETNA, NE
Difficult
30 - 60 mins
Nutdriver, Screw drivers, Socket set
Well I did it all wrong from the get go. I did finally do a search on how to replace it and then it was quite easy. Learn from me, watch video and save yourself tons of hassle.
Was this helpful?
Thank you for voting!
GE oven showed "F2" error code and was over-heating
5 of 6 peoplefound this instruction helpful.
Kyle from AURORA, CO
Really Easy
30 - 60 mins
Nutdriver
I am not the handiest person in the world, and this repair was easy even for me. If you suspect that the temperature sensor is the problem, do yourself a favor and buy this inexpensive replacement part and install it yourself prior to calling a professional who will charge a service fee just for checking it out. Pull your oven out from
... Read morethe wall so you can access the back. Unscrew the small nuts on the back to remove the sheet metal cover. Find the wire that goes to the sensor and unplug the plastic coupling. In the oven, unscrew the one nut that secures the sensor to the back wall of the oven. Pull the broken sensor out and replace it with the new sensor. Feed the wire through to the back and plug the new sensor into the same wire that was just disconnected. Reinstall all of the nuts. Do a "test cook" on some frozen food to ensure that the temperature seems correct (i.e., does it cook as expected in the recommended amount of time). The actual repair takes less than five minutes. I put "30-60 minutes" to account for unplugging the oven, pulling it out, removing the screws, replacing the screws, pushing it back in, and testing the temperature.
Read less
Was this helpful?
Thank you for voting!
Shorted the control panel changing bulb without shutting off power dumbass
5 of 6 peoplefound this instruction helpful.
Stephen from BELLINGHAM, MA
Really Easy
30 - 60 mins
Nutdriver, Screw drivers
Replaced control panel after removing original control panel facing with heat gun and Wala
I unscrewed and removed the old element from inside the oven, but unfortunately there wasn't enough extra wire to pull through and attach the new element from the front, so I had to move the oven away from the wall, remove the back panel, and connect the new element from the rear. Very self-explanatory.
The new element had som
... Read moree kind of spray or coating on it that caused some smoke for a few minutes, but then it worked fine.
Read less
Was this helpful?
Thank you for voting!
One of the drawer supports broke off
5 of 7 peoplefound this instruction helpful.
John from Sandy Hook, CT
Really Easy
Less than 15 mins
Nutdriver
I pulled out the drawer and inserted the new support. This one inserts into the back of the drawer as opposed to the sides. I had ordered two of the replacements even though I only needed one and decided to replace both. I think it was a good move as the drawer works better than when we first got it. Just one simple screw made it com
... Read moreplete.
Read less
Was this helpful?
Thank you for voting!
F2 Error on Display
4 of 4 peoplefound this instruction helpful.
Tom from FORNEY, TX
Very Easy
Less than 15 mins
Nutdriver, Screw drivers
The repair was very easy to do. Our oven was showing the F2 error code, which is associated with an over-temperature fault. Upon inspection, the oven was warm, but definitely not beyond the temperature threshold. I researched the issue and found this temperature sensor. Swapping the sensor was extremely easy. You take off the back pa
... Read morenel of the oven, unhook a single wiring harness, and undo some bolts inside the oven, which allows you to pull off the old sensor. Simply hook up the new sensor to the harness, pull everything back through, replace the fasteners, and you're good to go.
Read less
Was this helpful?
Thank you for voting!
Oven Temp. went too high and the door locked. Burnt the food
4 of 4 peoplefound this instruction helpful.
Nathan from BILLINGS, MT
Very Easy
Less than 15 mins
Nutdriver, Screw drivers
This temperature sensor is very easy to replace. There are two screws inside the oven in the top middle of the back of the oven. Take these off. on the back of the stove there is a metal plate with 5 screws I believe. Take these off with a nut driver. Then you will see a white connector coming from the spot where you took the other screws
... Read more off. Take the white connector apart and pull out the temperature sensor from the inside of the oven. Then put the new one in.
Read less
Was this helpful?
Thank you for voting!
outside element burned out
4 of 4 peoplefound this instruction helpful.
peter from westfield, MA
Really Easy
Less than 15 mins
Screw drivers
. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two plugs. plugged in the new element and screwed it in place
My Orders
