Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven temperature would not go above 240 degrees
7 of 9 peoplefound this instruction helpful.
Glenn from Grapevine, TX
Really Easy
15 - 30 mins
Nutdriver
Pulled the oven out and unplugged it. Removed five screws and the back cover. Disconnected the electrical connection. Removed one screw and pulled the sensor out. Installed the sensor and screw. Made the electrical connection on the back, replaced the cover and five screws. Plugged the electrical cord back in and tested the oven tem
... Read moreperature compared to the setting. Worked great. My wife then made a small batch of muffins to test it out and they were good.
Read less
Was this helpful?
Thank you for voting!
Had to replace the broiler element
6 of 6 peoplefound this instruction helpful.
Mike from Birdsboro, PA
Really Easy
15 - 30 mins
Nutdriver
Removed the old element with a nut diver and put the new one in. Very simple instalation.
Amazingly the part arrived in just two days...
My T-Bone steaks are cooked just the way I like them again.
MikeS, Birdsboro, PA
Was this helpful?
Thank you for voting!
F2 error; over heating, unknown reason
6 of 6 peoplefound this instruction helpful.
Tim from LEAVENWORTH, WA
Very Easy
15 - 30 mins
Nutdriver, Screw drivers
I just followed the instructions on the link provided with the part
Was this helpful?
Thank you for voting!
switch went to high setting no matter what the setting was
10 of 19 peoplefound this instruction helpful.
Frank from Glen Cove, NY
Easy
15 - 30 mins
Nutdriver, Screw drivers
took off cover, pulled all wires off switch, pushed wires on new switch, put cover back on. Whalaa..
Was this helpful?
Thank you for voting!
Baking element cut on fire
5 of 5 peoplefound this instruction helpful.
Hedayat from LONGWOOD, FL
Easy
15 - 30 mins
Nutdriver, Pliers
In this case I had to pull the range out to disconnect the power and also to remove the plate covering the electrical connectors. This was the only way to reconnect the elements terminals since the wires were too short to do it inside the oven. Undo the 2 screws holding the element in place from inside the oven to remove and install the n
... Read moreew one before connecting the terminals from the back. Put back the rear cover and reconnect the power.
Read less
Was this helpful?
Thank you for voting!
When inspecting the back of my oven I noticed the cable had been pushed under (my guess from the mouse I found electrocuted where the power lines come in) and was touching one of the element prongs which burned the covering.
6 of 8 peoplefound this instruction helpful.
Mary from Bolton, MA
Really Easy
Less than 15 mins
Socket set
Not counting unplugging it and taking off the 3 back panels of the oven (< 5 min.) It took < 2min. to change out. Unclipped cable in back, unscrewed one screw inside of oven at top between the two elements and pulled cable through to front, reversed to attach new sensor. Buttoned up the back, plugged back in and was good to go.
Was this helpful?
Thank you for voting!
Oven in accurate temp too low.
6 of 8 peoplefound this instruction helpful.
Joseph from LIBERTY HILL, TX
Really Easy
Less than 15 mins
Nutdriver
Open the oven , remove one screw holding the sensor remove the sensor and replace the sensor.
Was this helpful?
Thank you for voting!
Outer ring of burner did not work
5 of 5 peoplefound this instruction helpful.
Barry from Bradenton, FL
Really Easy
Less than 15 mins
Pliers, Screw drivers, Socket set
1- opened oven door 2- unscrewed 2 screws underneath top with a socket wrench 3- unscrewed clips that held burner 4-used needle nose pliers to pull off wire clips off old burner 5- placed wires onto new burner 6- opened clips to make it easier to reinsert burner 7-reattached burner 8-Replaced top
... Read morer />The hardest part was unscrewing the 2 screws that held the top in place due to the position of the screws
Read less
Was this helpful?
Thank you for voting!
Red Light On
5 of 5 peoplefound this instruction helpful.
Lawrence from DECATUR, AL
Really Easy
30 - 60 mins
Red Light Off
Was this helpful?
Thank you for voting!
The small burner inside the double burner shortd out.
5 of 5 peoplefound this instruction helpful.
david from PORT ORANGE, FL
Easy
30 - 60 mins
Nutdriver, Pliers, Screw drivers, Socket set
The first thing was to watch U-Tube . The replacement burner was being replaced in a GE glass top range. Exter tools were required than depicted in the U-Tube project. The project overall was not dificult for me however I was a general contracter for over 25 years
Was this helpful?
Thank you for voting!
Old coil burned out
5 of 5 peoplefound this instruction helpful.
Matthew from Cynthiana, KY
Easy
15 - 30 mins
Nutdriver
After reading all the repair stories I knew that their wasn't any extra wire when the old element is removed. Well, even with that knowlage one of the wires came loose and slipped back in. Fortunately I was able to remove a panel in back and push it back through. I was afraid I would have to take off the whole back but instead there is a
... Read morepanel covering the wire running down the center of the oven. After removing 5 screws with the same nut driver as the one for the coils I had it done in minutes. I had no problem and I am NOT a 'do it yourselfer'. Oh, did I mention I ordered the part on Friday and received it on Saturday standard shipping? Pays to live the next state over from the place shipping it.
Read less
Was this helpful?
Thank you for voting!
Glass- top range had two burners that would not regulate. Burners went to HIGH when dial was set on any setting, even low.
5 of 5 peoplefound this instruction helpful.
christopher from WOODSTOCK, GA
Really Easy
30 - 60 mins
Nutdriver, Screw drivers
Replaced switches. Dual power switch had been updated and didn’t match original part but there were accurate instructions in package to allow correct wiring easily. Good job Parts Select.
GE oven showed "F2" error code and was over-heating
5 of 6 peoplefound this instruction helpful.
Kyle from AURORA, CO
Really Easy
30 - 60 mins
Nutdriver
I am not the handiest person in the world, and this repair was easy even for me. If you suspect that the temperature sensor is the problem, do yourself a favor and buy this inexpensive replacement part and install it yourself prior to calling a professional who will charge a service fee just for checking it out. Pull your oven out from
... Read morethe wall so you can access the back. Unscrew the small nuts on the back to remove the sheet metal cover. Find the wire that goes to the sensor and unplug the plastic coupling. In the oven, unscrew the one nut that secures the sensor to the back wall of the oven. Pull the broken sensor out and replace it with the new sensor. Feed the wire through to the back and plug the new sensor into the same wire that was just disconnected. Reinstall all of the nuts. Do a "test cook" on some frozen food to ensure that the temperature seems correct (i.e., does it cook as expected in the recommended amount of time). The actual repair takes less than five minutes. I put "30-60 minutes" to account for unplugging the oven, pulling it out, removing the screws, replacing the screws, pushing it back in, and testing the temperature.
Read less
Was this helpful?
Thank you for voting!
surface burner switch was burned
5 of 6 peoplefound this instruction helpful.
abbas from redmond, WA
Really Easy
More than 2 hours
Nutdriver, Screw drivers
After receiving the new swith from part select in less than four days with surface mail as they promised, it took me less than five minutes to replace the new swith with the old one. The only tools that I needed were A) a 5/16 nut driver to remove the back panel in order to get an access to the swith.B) a phillips screw driver to remove t
... Read morehe swith assembley from the front panel.
I had an estimate from a technician to do the job for 196.27 dollars!!!!!:(:(. I only paid 29.56 Dollars to part select to get this swith, including the shipping.:):):)
Read less
Was this helpful?
Thank you for voting!
Shorted the control panel changing bulb without shutting off power dumbass
5 of 6 peoplefound this instruction helpful.
Stephen from BELLINGHAM, MA
Really Easy
30 - 60 mins
Nutdriver, Screw drivers
Replaced control panel after removing original control panel facing with heat gun and Wala
My Orders
