EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

JCBP78SJ1SS General Electric Range - Instructions

All Instructions for the JCBP78SJ1SS
61 - 75 of 447

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
A piece of the Bake Element broke off
6 of 6 people found this instruction helpful.
  • Keith from Charlotte, NC
  • Easy
  • Less than 15 mins
  • Nutdriver
I unplugged the stove then took the oven racks out. Then I took a nutdriver and took out the 2 screws that held the Bake Element in place. Pulled the 2 prong's out of the oven and removed the wires from the tips. They pulled right off.
Took out the new Bake Element and reversed the process. Attached the 2 wires put the 2 prong's bac k into the holes and screwed the 2 holding screws back in. Plugged the Stove back in and turned her on. Doing it myself saved me $150.00.
Was this helpful?
Thank you for voting!
bake element burned out.
6 of 6 people found this instruction helpful.
  • harold from spearman, TX
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Pliers
Turn off power to oven,remove two screws holding element in place,pull element forward approx. 1" and unplug wires,remove element. Install new element in reverse order of above.
Was this helpful?
Thank you for voting!
Bake element broke into pieces
6 of 6 people found this instruction helpful.
  • Rita from LYMAN, SC
  • Very Easy
  • Less than 15 mins
  • Nutdriver
Disconnect electric at panel box. Pull oven out. Remove 5 screws from rear panel. Pull off the 2 clips at the tips of the old element which is located about 2/3 down the back side of the oven. Remove broken element from inside the oven and slide new element in place. Push 2 clips firmly on the ends of the new element. Replace back co ver. Turn power on. Test oven. Slide oven back in place.
Was this helpful?
Thank you for voting!
switch went to high setting no matter what the setting was
10 of 19 people found this instruction helpful.
  • Frank from Glen Cove, NY
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
took off cover, pulled all wires off switch, pushed wires on new switch, put cover back on. Whalaa..
Was this helpful?
Thank you for voting!
Old coil burned out
5 of 5 people found this instruction helpful.
  • Matthew from Cynthiana, KY
  • Easy
  • 15 - 30 mins
  • Nutdriver
After reading all the repair stories I knew that their wasn't any extra wire when the old element is removed. Well, even with that knowlage one of the wires came loose and slipped back in. Fortunately I was able to remove a panel in back and push it back through. I was afraid I would have to take off the whole back but instead there is a panel covering the wire running down the center of the oven. After removing 5 screws with the same nut driver as the one for the coils I had it done in minutes. I had no problem and I am NOT a 'do it yourselfer'. Oh, did I mention I ordered the part on Friday and received it on Saturday standard shipping? Pays to live the next state over from the place shipping it.
Was this helpful?
Thank you for voting!
Oven in accurate temp too low.
6 of 8 people found this instruction helpful.
  • Joseph from LIBERTY HILL, TX
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Open the oven , remove one screw holding the sensor remove the sensor and replace the sensor.
Was this helpful?
Thank you for voting!
Outer ring of burner did not work
5 of 5 people found this instruction helpful.
  • Barry from Bradenton, FL
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers, Socket set
1- opened oven door
2- unscrewed 2 screws underneath top with a socket wrench
3- unscrewed clips that held burner
4-used needle nose pliers to pull off wire clips off old burner
5- placed wires onto new burner
6- opened clips to make it easier to reinsert burner
7-reattached burner
8-Replaced top