- Home
- JCBP77SM1SS
- Instructions
JCBP77SM1SS General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The storage drawer came without supports.
2 of 4 people
found this instruction helpful.
-
Dock from Aurora, CO
- Really Easy
- Less than 15 mins
-
Nutdriver
I just removed the drawer and installed the rear supports as instructed on paper included with the part.
Was this helpful?
Thank you for voting!
Replacing handle spacer
1 person
found this instruction helpful.
-
Sherry from SAINT PAUL, MN
- Easy
- Less than 15 mins
-
Screw drivers
This one is simple. unscrew a portion of the door, install the spacer and screw back together. Worked well.
Was this helpful?
Thank you for voting!
The light inside the oven had burned out
3 of 7 people
found this instruction helpful.
-
Catherine from SEATTLE, WA
- Very Easy
- Less than 15 mins
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
... Read more />3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
... Read more />3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Read less
Was this helpful?
Thank you for voting!
Not Reaching Temperature above 300 Degrees
1 person
found this instruction helpful.
-
Ron from SAN TAN VLY, AZ
- Very Easy
- Less than 15 mins
-
Nutdriver
Take off 6 screws of back cover of the range, unplug the white wire. Go to the inside of oven, pull out racks. At the top of the oven is your Broiler element, in the center you will see a rod sticking out with one screw holding it in place. Take out screw and pull temperature sensor out toward you. Reverse steps to put it back together.
Was this helpful?
Thank you for voting!
Burner no longer heats
1 person
found this instruction helpful.
-
Anthony from Apopka, FL
- Very Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Remove two screws with nut driver that holds range top down. Turn off breaker or unplug before lifting top. Brace top with 2x4. Take picture with cell phone just in case. Orient replacement part with old burner. Remove one wire at a time and install on new burner in corresponding correcting terminal. be sure they are snug. Drop top insta
... Read more
ll nuts . Test! Done! I am not an electrician!!!!!!!! Please do not publish !!!!
Read less
Was this helpful?
Thank you for voting!
oven door gasket needed replaced
1 person
found this instruction helpful.
-
Mary from LONGS, SC
- Very Easy
- Less than 15 mins
Ordered the part, it arrived and 5 minutes later it a complete installation
Was this helpful?
Thank you for voting!
Burner burned out
1 person
found this instruction helpful.
-
Daniel from Norborne, MO
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Very easy. Unpluged range from outlet, took two screws from the front under side of the range top, raised cook top up, took off four wires from burner, removed two screws than holds burner on cook top, replaced with new burner, installed two screws that hold burner in place, installed the four wires to burner, lowered cook top back into
... Read more
place replaced two screws that hold cook top down, pluged back into outlet. DONE!
Read less
Was this helpful?
Thank you for voting!
burner didn't work
1 person
found this instruction helpful.
-
Richard from Coon Rapids, MN
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
lift stove top, 2 undermount screws. Then unplug 4 wires, I did them 1 at a time plugging into new burner as I go so I wouldn't screw up. Take 2 screws out of old burner to stove top, # all around circle put screws in same # on new burner.Done Good experience all the way around. Order delivery and install
Was this helpful?
Thank you for voting!
Replaced oven door gasket
1 person
found this instruction helpful.
-
Paul from JACKSONVILLE, FL
- Really Easy
- 15 - 30 mins
-
Screw drivers
Remove old stained gasket and replaced with new. Only $57.00!
Was this helpful?
Thank you for voting!
Burned out
1 person
found this instruction helpful.
-
Dean from Elkton, FL
- Really Easy
- 15 - 30 mins
-
Screw drivers
Remove two screws to loosen the ceramic top....prop top open and change part...the part was exactly the same...change wires from one to the other and transfer clamps.....1st grade craft class would have done it in half the time I did......you folks have your parts inventory and description application to a science.....God Bless
Was this helpful?
Thank you for voting!
Plastic guide Broken
9 of 25 people
found this instruction helpful.
-
NICK from Vernon, CA
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
replaced Plastic Guides
Was this helpful?
Thank you for voting!
BASE OF BULB BROKE OFF & WELDED TO SOCKET
1 person
found this instruction helpful.
-
NEIL from ROCKY POINT, NY
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers
PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.
Was this helpful?
Thank you for voting!
The light socket cup could no longer hold the bracket that holds the light cover in place.
1 person
found this instruction helpful.
-
Roger from ALPENA, MI
- Really Easy
- 30 - 60 mins
-
Socket set
I watched a video of a similar model to familiarize myself with the required steps needed. I opened the back and disconnected the power cord and ground wires connected to the removable socket I then removed the lightbulb and removable socket from the oven interior side. I then removed the defective light socket cup and replaced it with th
... Read more
e part I purchased. After replacing the removable socket and lightbulb, the bracket holding the light cover functioned perfectly with the new light socket cup. Final steps were to reconnect the power and ground wires to the removable socket. I then replaced the back cover over the light socket cup area. One word of advise. Be very careful when removing and reconnecting the cables to the removable light socket.
Read less
Was this helpful?
Thank you for voting!
Change bulb
3 of 8 people
found this instruction helpful.
-
Louis from LEAGUE CITY, TX
- Really Easy
- 30 - 60 mins
-
Nutdriver
Easy
Was this helpful?
Thank you for voting!
Burner didnt heat
2 of 5 people
found this instruction helpful.
-
Ernest from Charlestown, NH
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
The unit has two spring clips that hold it in place. Also two screws that hold the element to the clips. It comes apart ok but doesn't go back as easy. I didn't remove the top as there was room to work from under it.
My daughter held the top down against a wooden dowl i was using as a prop rod . My wife held the unit in pla ... Read more ce . I finally got the clips back on and the screws back in . Centered the unit , transfered the wires , and it works perfect . Only three people and 30 min.
Thank you PartSelect for all your help !!
My daughter held the top down against a wooden dowl i was using as a prop rod . My wife held the unit in pla ... Read more ce . I finally got the clips back on and the screws back in . Centered the unit , transfered the wires , and it works perfect . Only three people and 30 min.
Thank you PartSelect for all your help !!
Read less
Was this helpful?
Thank you for voting!