EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

JCBP77DM1BB General Electric Range - Instructions

All Instructions for the JCBP77DM1BB
76 - 90 of 132

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Replaced cracked inner oven door glass
1 person found this instruction helpful.
  • Sherry from SAINT PAUL, MN
  • Easy
  • 1- 2 hours
  • Screw drivers
This went pretty smoothly. Watch the video and just follow along step-by-step and it goes well. It would have only taken about 30-45 minutes (even being careful and slow) but I ended up placing the glass twice (be very careful and triple check that all the insulation gets poked under the housing and none is sticking out). The first time I had a small piece sticking out. (Use gloves for this part so your hands don't itch). The second time I needed to redo part of it is I forgot one of the spacers on the door handle and had to get that in there so the handle worked properly. I also took the time to clean the oven while the door was off so that took some time. Total I probably had 1.5-2 hours into this project but at least half of that was me cleaning and being fussy. This is an easy repair. I'm not a confident repair person and this wasn't difficult. It was a little time consuming but well worth the cost vs calling a repair person or buying a new appliance. You do need to have a specialty star head on a screwdriver but my simple tool kit had all the tools I needed. The oven has been working great since the repair.
Was this helpful?
Thank you for voting!
Burner didnt heat
2 of 5 people found this instruction helpful.
  • Ernest from Charlestown, NH
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers
The unit has two spring clips that hold it in place. Also two screws that hold the element to the clips. It comes apart ok but doesn't go back as easy. I didn't remove the top as there was room to work from under it.

My daughter held the top down against a wooden dowl i was using as a prop rod . My wife held the unit in pla ce . I finally got the clips back on and the screws back in . Centered the unit , transfered the wires , and it works perfect . Only three people and 30 min.

Thank you PartSelect for all your help !!
Was this helpful?
Thank you for voting!
middle burner not working
2 of 5 people found this instruction helpful.
  • joy from st. augustine, FL
  • Easy
  • 15 - 30 mins
  • Nutdriver
Use a 1/4" nutdriver and remove the screws that are on the bottom corners of the range top.Prop up the range top high enough for ease of using 1/4" nut driver. Take a picture of the wiring for future reference on re-installing wiring. Note arrow location on burner and remove 1/4" screws holding the clamps to the burner in place and place to the side for re-install on new burner.Remove wiring off old burner.Hold new burner in place with arrow location in previous location and notice holes where clamps will go. Screw clamps on burner using original screws and snap in mounting slots on stove.Re-install wiring.Lower range top and re install 2 screws , 1 in each corner under range top. Test for proper operation and enjoy!
Was this helpful?
Thank you for voting!
Change bulb
3 of 8 people found this instruction helpful.
  • Louis from LEAGUE CITY, TX
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
Easy
Was this helpful?
Thank you for voting!
Hot burner light lens broke off.
1 of 2 people found this instruction helpful.
  • Charles from NEKOOSA, WI
  • Easy
  • 15 - 30 mins
  • Screw drivers
Pull range away from back wall. Remove panel behind control knobs by removing the screws that hold it on. Find hot burner light that holds lens. Remove broken part of lens. Insert new lens into hole on front of control panel and into hot burner light receptacle. Replace back panel. Slide range back into place.
Was this helpful?
Thank you for voting!
dropped & broke the oven light bulb cover
1 of 2 people found this instruction helpful.
  • joseph from san jose, CA
  • Really Easy
  • Less than 15 mins
popped the new one on!
Was this helpful?
Thank you for voting!
Knob stem broke off.
1 of 2 people found this instruction helpful.
  • DALE from FREMONT, NE
  • Very Easy
  • Less than 15 mins
  • Nutdriver, Pliers, Screw drivers
Pulled stove out to access back panel. Unscrew broken switch/stem. Replaced each wire one at a time to make sure they went in right spot. Screw in new switch. Replaced back panel.
Was this helpful?
Thank you for voting!
Oven will not heat
1 of 3 people found this instruction helpful.
  • Joseph from Homosassa, FL
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
As many people have encountered, my oven would not heat but the igniter would be bright orange and glow! Over time, the igniter wears and degrades causing oxidation to the surface. This cause the igniter to fail and operate at a lower current level, below 2.8 amps! Normal igniters operator over 3.0 to 3.1 amps. When is happens, a low c urrent igniter does not have enough input to the control valve to tell the valve to open to allow gas to flow over the igniter to light the oven, thus heat the oven! This has got to be the NUMBER one reason for an oven not heating!
Was this helpful?
Thank you for voting!
oven was not getting up to temp
0 of 1 people found this instruction helpful.
  • walter from townshend, VT
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Once I opened up the back of the range, the sensor wires where there and burnt just like your info said. One nut to take off in the oven and the sensor came right out and the new one went right in. The oven works great, cooked the turkey today. The worst part of the repare was the cleaning behind and under the range, it hasn't moved since it was put in 6 years ago. Very pleased with PS.
Was this helpful?
Thank you for voting!
F2 error when oven was heating up, along with a beeping noise and then it shut off
0 of 1 people found this instruction helpful.
  • Lori from Paris, TN
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Unplugged oven, turned off breaker, took cover off back of oven, removed old sensor by disconnecting in back of oven and undoing screw inside oven. Pulled old one out replaced with new took 15min. Cost me less than $20. Parts Select rocks! Even received part in two days with standard shipping!
Was this helpful?
Thank you for voting!
F2 error code
0 of 2 people found this instruction helpful.
  • jud from gatesville, TX
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Really easy fix. Unplug oven. With a 5/16 nut driver take the 5 screws out of the center long tin cover and remove. Unplug little white temperature sensor plug located between broil heating element. Open oven door and remove one screw holding temp. sensor using same nut driver and simply pull out old sensor. Install new sensor. It's tha t easy. No more f2 been working like a champ!!!
Was this helpful?
Thank you for voting!
Light burnt out.
2 of 8 people found this instruction helpful.
  • Roscoe G from ROCHESTER, NY
  • Very Easy
  • Less than 15 mins
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this helpful?
Thank you for voting!
Stove drawer rear guides broken
  • Robert from Shakopee, MN
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Installed new guides with a nut driver without any problems.
Was this helpful?
Thank you for voting!
oven not warming, f2 indicating overheat
  • David from Lisle, IL
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Removed 4 screws from back panel, disconnected small electricsl connector from sensor, removed one mounting screw from sensor inside oven,pulled wires through and removed old sensor. Fed wires for new sensor through and connected electrical connector, installed panel, installed mounting screw on sensor and checked oven, worked like a cham p. Took 5 minutes.
Was this helpful?
Thank you for voting!
Hard to move drawer in and out because the rear drawer supports broke off.
  • Steven from Lansdale, PA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Repair was very easy - less than a few minutes - just had to screw in 2 screws to the new drawer supports.
Was this helpful?
Thank you for voting!
All Instructions for the JCBP77DM1BB
76 - 90 of 132