- Home
- JCBP67DP1BB
- Instructions
JCBP67DP1BB General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Hot burner light lens broke off.
1 of 2 people
found this instruction helpful.
-
Charles from NEKOOSA, WI
- Easy
- 15 - 30 mins
-
Screw drivers
Pull range away from back wall. Remove panel behind control knobs by removing the screws that hold it on. Find hot burner light that holds lens. Remove broken part of lens. Insert new lens into hole on front of control panel and into hot burner light receptacle. Replace back panel. Slide range back into place.
Was this helpful?
Thank you for voting!
Water dumped over in in my overhead microwave, which dripped down on, & shorted out a burner switch.
1 of 3 people
found this instruction helpful.
-
Deanna from Buckeye, AZ
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
My husband had already removed the back plate form the stove and detached the wires from the old burner switch because it was keeping the burner on. He unscrewed the old switch and removed it. He then popped in the new switch, attached the wires to the correct contacts, and put the back plate back on. We plugged in the stove, and that
... Read more
burner works good as new.
Read less
Was this helpful?
Thank you for voting!
fried oven control using raid
4 of 13 people
found this instruction helpful.
-
Kerry from Loveland, CO
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
replaced oven clock control ref maintenance manual, 4 screws and 8 wires. plugged in new control and op checks good.
Was this helpful?
Thank you for voting!
burner was inoperative
0 of 2 people
found this instruction helpful.
-
bryan from cocoa, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
verified switch operation , checked continuity of burner element found open ordered new part and installed next day
after extremely fast
service from partselect thank you
after extremely fast
service from partselect thank you
Was this helpful?
Thank you for voting!
eye wouldnt come on
0 of 2 people
found this instruction helpful.
-
daniel from valentines, VA
- Really Easy
- 15 - 30 mins
-
Nutdriver
removed the top section on stove and removed the wires off swtitch and put on new one then put new switch in
Was this helpful?
Thank you for voting!
Light burnt out.
2 of 8 people
found this instruction helpful.
-
Roscoe G from ROCHESTER, NY
- Very Easy
- Less than 15 mins
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this helpful?
Thank you for voting!
Burner not heating.
1 of 5 people
found this instruction helpful.
-
Jack from Greensboro, GA
- Really Easy
- 30 - 60 mins
-
Screw drivers
Isolated to control switch.
Replaced
Replaced
Was this helpful?
Thank you for voting!
light keep burning out in oven.
2 of 8 people
found this instruction helpful.
-
john from Mc Kees Rocks, PA
- Really Easy
- 30 - 60 mins
-
Nutdriver
Remove the door. Just open a little and pull up. Removed racks. Removed 3 screws with nutdriver. Pulled out housing. Disconnected 2 wires. Assembled new housing with with bulb receptacle and gasket. Reconnected wires and crimped a little to make them snug. Pushed housing back into hole. Put 3 screws back in, inserted bulb and cover. Slid
... Read more
door back on and done. 30 minutes at most.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Shorted Control Unit -
-
Gerald from Plantsville, CT
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
Control unit was easy to remove ,wires color coded-the face plate(key pad) needed to be separated from the old unit. Carefully used a hair dryer to warm the decal. . . Secured the old unit gently in a vise, warmed ( and separated slowly, with a razor blade and thin putty knife(patience). . Once removed, applied to the new unit. .
... Read more
. 5 Stars to partselect for service. . . . Turned a $400 repair into $100 do-it your self. Partselect will be my 1st "go to" from now-on.
Read less
Was this helpful?
Thank you for voting!
Burner Would Not Turn Off
-
BILLY from WEBSTER, FL
- Really Easy
- 30 - 60 mins
-
Nutdriver
Replace control switch
Was this helpful?
Thank you for voting!
one leg of the terminal block was loose and overheated under load.the terminal block melted and could have caused a fire.
-
brendan from lebanon, NH
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set, Wrench set
I took a picture of the setup and damage . I then disconnected the burnt wires and replaced the wires . Then I installed the new terminal block and connected the wires to the proper positions. The reason for the failure was that the delivery people didn't tighten the cord when they installed the stove . I would check the connections per
... Read more
iodically as to avoid another situation like this .
Read less
Was this helpful?
Thank you for voting!
Mother board was blown
-
Kenneth from Bradenton, FL
- Easy
- 15 - 30 mins
Purchased the board installed it and saved about 130 dollars.
Was this helpful?
Thank you for voting!
oven control panel was blacked out..no clock no start.
-
Pam from Daphne, AL
- Easy
- 15 - 30 mins
-
Screw drivers
Took out the old control module and removed the sticker and reattached sticker to new part and installed the plugs, put the screws back in and it started working, thankyou so much.
Was this helpful?
Thank you for voting!
broken light socket
-
James from Monterey, TN
- Easy
- 15 - 30 mins
-
Nutdriver
The only tool needed was a nutdriver to remove the lamp socket. I needed my head mounted light to see what I was doing, and everything went smoothly from there. Simple job.
Was this helpful?
Thank you for voting!
Blew the electronic Control Board
-
PETE from MANCHACA, TX
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
It was easy to replace it. Just remove the screws and unplug each wire and plug them back. The problem was to take off the plate cover that has the printed letters on. The plate cover cost more than the Electronic Control Board.
Was this helpful?
Thank you for voting!