- Home
- JCBP67CM2BB
- Instructions
JCBP67CM2BB General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Bake unit started on fire then cracked in half.
2 of 4 people
found this instruction helpful.
-
Sachin from Omaha, NE
- Easy
- Less than 15 mins
-
Socket set, Wrench (Adjustable)
We ordered the part from PartSelect and received it the next day. Didn't even have to move the range out from the wall. Just unscrewed the two screws on the back wall of the stove that hold the bake element in place with a socket wrench, then pulled the old bake element and wires out about 2-3 inches so we could disconnect the old bake
... Read more
unit. The element was kind of hard to pull out, but after you pull it from the wires, just plug in the new bake unit, push the wires back in and put the screws back in. Oven was up and working again!
Read less
Was this helpful?
Thank you for voting!
Bake element was burnt out.
1 person
found this instruction helpful.
-
Bertram from ABERDEEN, MD
- Very Easy
- Less than 15 mins
-
Socket set
1.Disconnect the power cord. 2.Remove two screws pull the element out. 3.Disconnect the wires attach to element. 4. Install the new element connecting the wires. 5. Align element
... Read more
with holes and tighten screws. 6. Plug in power cord and begin to cook.
Read less
Was this helpful?
Thank you for voting!
Oven was very slow to heat
1 person
found this instruction helpful.
-
James from CANAL FULTON, OH
- Very Easy
- Less than 15 mins
-
Nutdriver
Removed the rear panel from the Range using the nut driver. pulled the terminal wires off the back of the heating element. Double checked if there was continuity across the heating element terminals before removing the element. If there is none, its bad. remove the two screws inside the oven holding the element in place. Once free, lift t
... Read more
he front of the element to about 30 degrees and pull towards you. Insert the new element in the reverse manner then secure it using the two screws. Push the terminal wires onto the terminals on the back of the element and reinstall the rear panel.
Read less
Was this helpful?
Thank you for voting!
Back element was broken
1 person
found this instruction helpful.
-
Shiirley from CASPER, WY
- Really Easy
- Less than 15 mins
-
Pliers
My son did it by using pliers. He took out the screws that held the element in and pulled it out and used the pliers to pull the wires out of the old one and snapped the new one in . put it back together. about 5 minutes.
Was this helpful?
Thank you for voting!
Lower heating element broke and burst in flames
1 person
found this instruction helpful.
-
Heinz from Colleyville, TX
- Easy
- 15 - 30 mins
-
Nutdriver
On the website, the heating element looked exactly the same with same measurements as the old one. However, the part I received did not match. The screw holes where the element attaches to the back were wider apart and higher. Plus, the leads curved up instead of being straight.
Was this helpful?
Thank you for voting!
Bottom element fell apart
1 person
found this instruction helpful.
-
david from Cromwell, CT
- Easy
- 15 - 30 mins
-
Screw drivers
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. ordered the part and connected the element back to the two wires replaced the two screws plugged in the stove turned on the oven and we were back in business,
Was this helpful?
Thank you for voting!
Heating element literally blew apart during use one. We have no idea why,
1 person
found this instruction helpful.
-
Jon from Fort Worth, TX
- Easy
- 15 - 30 mins
-
Screw drivers
First, pulled out the old heating element and all the peices that were left after it fell apart. Since when you pull out the old one, the wires it connects to tend to recess back into the oven wall, I had to pull out the oven and take the back cover off in order to push the wires and connectors back through the receptacle in the oven. T
... Read more
his was really easy as you only have to remove 5 screws from the middle panel on the back of the oven rather than the entire oven back. Once the wires were back through, I just plugged in the new unit. The oven works just like new now. I'm sure I was able to save between $75 to $100 just for the service call by doing this myself.
Read less
Was this helpful?
Thank you for voting!
oven wouldn't heat
1 person
found this instruction helpful.
-
JEAN-C. from PARRISH, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver
removed two screws that hold the element in place and then removed the access rear panel it was much easier to disconnect the element than have to stick my head in the oven to gain access.time :15 minutes.
Was this helpful?
Thank you for voting!
element burned apart
2 of 4 people
found this instruction helpful.
-
DENNIS from shandon, CA
- Easy
- 15 - 30 mins
-
Pliers
pulled range out,unplugged it,thenI removed the two screws that hold the element in place.take back cover off, then pulled the element out about 3 inches and disconnected the two wires.put new element in,put wires and screws back in place,checked to see if worked,did not work,check and reset breaker,it works put cover back on,push range i
... Read more
n palce and done.
Read less
Was this helpful?
Thank you for voting!
Oven heater coil burned out
1 person
found this instruction helpful.
-
David from Canterbury, CT
- Really Easy
- 15 - 30 mins
-
Nutdriver
Removed power plug- disconnected wire, removed cover over wires two screws, and removed old heated strip, held in by two screws inside of oven
Slide in new coil installed two screws, connected two wires replaced guard over wires, plugged in stove, cooked a rubarb pie, success
Slide in new coil installed two screws, connected two wires replaced guard over wires, plugged in stove, cooked a rubarb pie, success
Was this helpful?
Thank you for voting!
Oven board went out
1 person
found this instruction helpful.
-
Jackie from TICKFAW, LA
- Very Easy
- 15 - 30 mins
-
Pliers
One wire at at time then used my razor blade to get front off stuck right back on
Was this helpful?
Thank you for voting!
Plastic guide Broken
9 of 25 people
found this instruction helpful.
-
NICK from Vernon, CA
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
replaced Plastic Guides
Was this helpful?
Thank you for voting!
Knob part broke on & off switch.Got a nee
1 person
found this instruction helpful.
-
Sandra from Saint Johns, AZ
- Very Easy
- 15 - 30 mins
Got a new knob.
Was this helpful?
Thank you for voting!
bake element burnt out
1 person
found this instruction helpful.
-
Keith from GOLDSBORO, NC
- Really Easy
- 30 - 60 mins
-
Nutdriver
unscrew and disconnect the old unit. Connect and screw in the new unit
Was this helpful?
Thank you for voting!
Oven no longer working after running the self clean option. Only Stove top burners worked
1 person
found this instruction helpful.
-
Dominick from THORNWOOD, NY
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
I began by turning off the breaker in the panel.
Slide the oven out into the open area.
Removed 3 screws in order to remove rear top panel.
Took 2 pictures of the wiring location on the PCB
Removed all wiring going to the circuit board total of 8.
Removed 4 screws in order to remove bad PCB.
Remove faceplate ... Read more from bad PCB (you will need to place this faceplate on the new PCB.
To Install.
Reverse steps above
Slide the oven out into the open area.
Removed 3 screws in order to remove rear top panel.
Took 2 pictures of the wiring location on the PCB
Removed all wiring going to the circuit board total of 8.
Removed 4 screws in order to remove bad PCB.
Remove faceplate ... Read more from bad PCB (you will need to place this faceplate on the new PCB.
To Install.
Reverse steps above
Read less
Was this helpful?
Thank you for voting!