JCBP66SP2SS General Electric Range - Instructions

Initially replaced the switch on the range--a simple job--pull the wires one by one and place them on the new switch. This did not resolve the problem, which meant that it was the burner, not the switch. I left the new switch in place and ordered a new burner. This, too, was simple, but involved creating a detailed drawing of the switch c ... Read more onnectors rather than photos, which, because of the crossing of similarly colored wires, might have been confusing. The only hitch was that the burner is attached to the top by indented clips that fit into pegs at numbered locations on the burner. The clips were very difficult to open and situate, but once done (and this step was the only one where a second person was required) the top was closed and screwed back in place (two screws) and it worked perfectly.

I am not the handiest person in the world, and this repair was easy even for me. If you suspect that the temperature sensor is the problem, do yourself a favor and buy this inexpensive replacement part and install it yourself prior to calling a professional who will charge a service fee just for checking it out. Pull your oven out from ... Read more the wall so you can access the back. Unscrew the small nuts on the back to remove the sheet metal cover. Find the wire that goes to the sensor and unplug the plastic coupling. In the oven, unscrew the one nut that secures the sensor to the back wall of the oven. Pull the broken sensor out and replace it with the new sensor. Feed the wire through to the back and plug the new sensor into the same wire that was just disconnected. Reinstall all of the nuts. Do a "test cook" on some frozen food to ensure that the temperature seems correct (i.e., does it cook as expected in the recommended amount of time). The actual repair takes less than five minutes. I put "30-60 minutes" to account for unplugging the oven, pulling it out, removing the screws, replacing the screws, pushing it back in, and testing the temperature.

I unscrewed to old glide and replaced it then re attached the screw

Being a front burner, I used a 24 in piece of wood to hold up range top. After removing to screws holding top. Made note of numbers on old burner and wire locations. Took off wires and three spring clips. Then replaced with new in numbered locations , wires next

This temperature sensor is very easy to replace. There are two screws inside the oven in the top middle of the back of the oven. Take these off. on the back of the stove there is a metal plate with 5 screws I believe. Take these off with a nut driver. Then you will see a white connector coming from the spot where you took the other screws ... Read more off. Take the white connector apart and pull out the temperature sensor from the inside of the oven. Then put the new one in.

The repair was very easy to do. Our oven was showing the F2 error code, which is associated with an over-temperature fault. Upon inspection, the oven was warm, but definitely not beyond the temperature threshold. I researched the issue and found this temperature sensor.
Swapping the sensor was extremely easy. You take off the back pa ... Read more nel of the oven, unhook a single wiring harness, and undo some bolts inside the oven, which allows you to pull off the old sensor. Simply hook up the new sensor to the harness, pull everything back through, replace the fasteners, and you're good to go.

Removed the oven door and shelves. Moved the oven out from wall, so that I could access the rear panel. Unplugged the oven. Removed the five (5) screws holding the rear panel in place and removed the panel. Disconnected the sensor at the connector. Removed the screw holding the sensor in place inside the oven and removed the sensor. Thea ... Read more ded the sensor wire through the rear of the oven wall. Installed the sensor and screw to hold it in place. Snapped the connector from the sensor to the mating connector at the rear of the oven. Installed the rear panel. Installed the five (5) screws to hold the panel. Plugged the oven back in and slide the oven back to the wall. Installed the oven shelves and the oven door.

took drawer out removed broken guide. It had 1 screw removed it put the new guide in place put screw back in. Put drawer back in stove, It works fine.

Unplug stove.
Remove rear panel of stove with a nut driver or socket. Remove knob from switch and use small screwdriver to remove screws on front panel switch. Remove and replace each wire contact one at a time to ensure correct wiring configuration. Replace screws on front panel to secure switch. Plug stove in and check that it work ... Read more s properly. Replace rear panel and move stove back in place.

I picked the least expensive and most likely issue with our oven that was not indicating a correct oven temperature. I am sure with a 15+ year appliance that the circuitry is on its way out but wanted to give this a try to avoid a new appliance purchase. Oven pre-heat setting takes much longer to finish with the age of the oven. However, ... Read more after the new sensor the oven will maintain a more even temperature for the cycle.

Removal of the sensor from the inside of the oven is a bit awkward since it is located between the broiler elements at the back but a nut driver was the correct tool and worked fine. A bit stuck with the heating of the connection but pretty simple to replace. Must remove the back first to uncouple the connector. Simplest part of the repair.

At best a temporary fix for a an appliance this old.

Replaced old with new.

Unscrewed the stove top and replaced the element.

Removed old gasket, did need to use pliers. However, it was easy. The new gasket just snapped in place ...super easy.

took nut driver to remove the old and replaced with new. simple.

slid the old ones out and slid the new ones in. done