- Home
- JCBP66SM1SS
- Instructions
JCBP66SM1SS General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
No Instructions
2 of 2 people
found this instruction helpful.
-
Richard from FAYETTEVILLE, GA
- Difficult
- More than 2 hours
-
Nutdriver, Pliers, Wrench (Adjustable)
Lots of jiggling until I found the screws to remove. After finally getting the top off the base there was the Instructions on a pamphlet taped to the bottom. The key tho get the top off is to remove the face and remove the proper screws( they are identifiable)unplug the electric plug 2 screws on the back sides and poof it is free!
Was this helpful?
Thank you for voting!
Bake element melted.
2 of 2 people
found this instruction helpful.
-
Allen from HENRICO, NC
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers
Would have helped it I knew the push on terminals of the bake element were visible and accessible to slide the terminals on from the back side of the stove in the beginning. There is not enough slack in the the terminal wires to connect them from the oven side, so you will have to open the back panel to retrieve a wire anyway. SO, CONNECT
... Read more
THE BAKE ELEMENT TO THE OVEN WALL FIRST ! Then, open the back panel of the stove and simply slide the terminals on the exposed slide terminals of the bake element.
Read less
Was this helpful?
Thank you for voting!
We dropped something on the cooktop & broke the glass
2 of 2 people
found this instruction helpful.
-
Sara from CHARLOTTE, NC
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
Unpack the new cooktop and set it upside down on a towel or blanket. Unplug the stove & pull it forward from between the counters. Open the oven door and remove the two screws securing the front edge of the cooktop. Lift & tilt the top up until you can unhook the back edge from the pins that hold it. Pull it forward until you can access t
... Read more
he two wiring harnesses & the green ground wire. Take a picture of the harnesses & pinch the sides to unclip & remove them. Unscrew the green ground wire and set the screw aside. Flip the cooktop over and take another picture of how the burners are attached to the cooktop. Unscrew the green ground wire & use needle-nosed pliers to carefully remove the clips holding the burners. This is a little tricky - the flat top of the clip has a small tab inserted in a numbered hole in the top of the burner. After removing the clips holding each burner, carefully move the burners onto the underside of the new cooktop. Use the photo you took to reposition the burners on the new cooktop and reattach the clips using the same numbered holes as before. Reattach the green ground wire. Carefully flip the cooktop back over on top of the oven and use the photo you took to reattach the wiring harnesses and green ground wire. Tilt the cooktop as you hook/hang the back edge back onto the pins (this was also a little hard). Reinsert the two screws under the front edge to resecure the cooktop. Plug it back in to the outlet, and push it back between the cabinets.
Read less
Was this helpful?
Thank you for voting!
Gizmo in oven that gets red hot when you bake had burned out.
3 of 6 people
found this instruction helpful.
-
B from Niceville, FL
- Easy
- 15 - 30 mins
-
Nutdriver
Gizmo = Bake Element held in place with 2 bolts inside of oven. Removing them only difficult because they are so deep in oven. I did not have the correct size nut driver so I started with my socket wrench then switched to putting the correct size socket on the end of a long screwdriver. After removing the 2 bolts fund element did not s
... Read more
lide out easily so went to back of stove and removed a metal protective cover. Found electrical lines secured to the ends of the element. Had someone hold element while I pulled each of the 2 loose - at which time bake element fell loose. Put new one in by reversing the process. That night wife set stove to Clean - and said best it has been cleaned in years.
Read less
Was this helpful?
Thank you for voting!
Heat element died
2 of 3 people
found this instruction helpful.
-
Andrea Hines from ELGIN, AZ
- Very Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Very easy to replace. So easy even a man can do it.
Was this helpful?
Thank you for voting!
My electronic control board went out so I could not use my oven. My oven light blew as well.
2 of 3 people
found this instruction helpful.
-
Stella from PADUCAH, KY
- Really Easy
- Less than 15 mins
-
Pliers, Socket set
I started with changing the bulb. I removed the small bracket that holds the glass cover over the bulb unscrewed the bulb and reversed to replace the bulb. To replace the control board I removed the top plate on the back of my stove took the small screw's out of the control panel and unplugged the wire's. Plugged the wire's into the right
... Read more
spots on the new control board and put it back together.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
lens snapped off on the inside-plug was left loose
3 of 6 people
found this instruction helpful.
-
RICKEY from MONTROSE, NY
- Easy
- Less than 15 mins
-
Screw drivers
popped out the remainder of old lens, then pushed in new ones and slipped on plugs.
Was this helpful?
Thank you for voting!
Cleaned oven with shelves inside...
3 of 6 people
found this instruction helpful.
-
Carol from Roanoke, VA
- Really Easy
- Less than 15 mins
I too made the mistake of cleaning the oven with the shelves in place. It doesn't really harm them...but they turn a tarnished brown color...they look dirty. These replacement shelves were a perfect match. Pricing was reasonable, communication was terrific and shipping was super fast. Happy camper here :-)
Was this helpful?
Thank you for voting!
Broken rear drawer support
2 of 3 people
found this instruction helpful.
-
Jesse from Knob Noster, MO
- Really Easy
- Less than 15 mins
-
Nutdriver
Installed the new brackets at the back of the drawer with the 2 screws provided. The new rear mount design is much better than than the old side mount.
Was this helpful?
Thank you for voting!
Bake element brokeand caught fire
2 of 3 people
found this instruction helpful.
-
Lillian from coral springs, FL
- Really Easy
- Less than 15 mins
-
Nutdriver
Ordered the bake element part from partselect.com. When the part arrived I removed the 2 6mm screws from the element, I used two clips to hold the wires in place so that they didn't receed back into the stove. I installed the bake element, installed the two scews ans was done. It took all of 10minutes.
Lily in Florida
Lily in Florida
Was this helpful?
Thank you for voting!
Lower bake element burned out
1 person
found this instruction helpful.
-
Belinda from Rockford, IL
- Really Easy
- Less than 15 mins
-
Nutdriver
I didn't know anything about this repair, other than I was replacing a part, so it never occurred to me that I needed to make sure there was no power to the oven. When I pulled the element out, there was a large spark. I flipped the breaker off, then finished the R&R.
Make sure you turn power off at the breaker, then replace ... Read more the element.
Tim
Make sure you turn power off at the breaker, then replace ... Read more the element.
Tim
Read less
Was this helpful?
Thank you for voting!
THE FACE PLATE IS HARD TO GET OFF THE OLD CONTROL BOARD. USE A THIN KNIFE
1 person
found this instruction helpful.
-
Melvin from WEBSTER, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
THE INSTRUCTIONS THAT COME IN THE EMAIL ARE VERY GOOD. BE SURE TO TAKE A PICTURE OF THE WIRING.
Was this helpful?
Thank you for voting!
Burned out
1 person
found this instruction helpful.
-
Dean from Elkton, FL
- Really Easy
- 15 - 30 mins
-
Screw drivers
Remove two screws to loosen the ceramic top....prop top open and change part...the part was exactly the same...change wires from one to the other and transfer clamps.....1st grade craft class would have done it in half the time I did......you folks have your parts inventory and description application to a science.....God Bless
Was this helpful?
Thank you for voting!
burner didn't work
1 person
found this instruction helpful.
-
Richard from Coon Rapids, MN
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
lift stove top, 2 undermount screws. Then unplug 4 wires, I did them 1 at a time plugging into new burner as I go so I wouldn't screw up. Take 2 screws out of old burner to stove top, # all around circle put screws in same # on new burner.Done Good experience all the way around. Order delivery and install
Was this helpful?
Thank you for voting!
Burner burned out
1 person
found this instruction helpful.
-
Daniel from Norborne, MO
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Very easy. Unpluged range from outlet, took two screws from the front under side of the range top, raised cook top up, took off four wires from burner, removed two screws than holds burner on cook top, replaced with new burner, installed two screws that hold burner in place, installed the four wires to burner, lowered cook top back into
... Read more
place replaced two screws that hold cook top down, pluged back into outlet. DONE!
Read less
Was this helpful?
Thank you for voting!