JCBP61SP3SS General Electric Range - Instructions

Followed the video and it was fast and quick.

Removed old gasket, did need to use pliers. However, it was easy. The new gasket just snapped in place ...super easy.

took nut driver to remove the old and replaced with new. simple.

Pull the range out from the wall to access the rear of the unit. Turn off power to the range by unplugging from the wall or turning off the breaker.
Remove the large back cover from the oven portion of the range. Locate the two small wires and connector which is located between the two connections for the broiler heating element. Unp ... Read more lug the small connector.
Open the oven door and remove the screw that holds the temperature sensor in place between the broiler heating elements on the inside of the oven. Gently pull the sensor and the wire connector through the hole and discard.
Feed the new connector and wire through the hole from the inside of the oven. Attach the sensor to the oven wall with the screw.
Go to the back of the unit and make sure that no insulation has gotten into the oven space. Re-route the new wire being careful not to let it touch the contacts for the broiler heating element. Reconnect the wires to the connector and replace the back cover of the oven.
Plug in the range or turn on the circuit breaker. Slide the range back into place and re-level the unit. Test the oven to make sure the temperature is accurate and will maintain temperature.

Removed two screws, and replaced element with a new one. Easy, works great.

First my son removed the two screws that held th element in place but first please tell everyone to turn off the breaker first. My son did not and he had gotten a shock from this and burned his hand. I think this is very important first. After cleaning up his hand he then replaced the element and tested it and it worked nicely.
< ... Read more br />Thank you for your prompt delivery and the correct part.

Sincerely
Kelly Didsbury

Had to pull out the refrigerator and put it in the dining room in order to pull out the stove to be able to get to the back of it. Had to take off the back of the stove to get to the wiring for the baking element, so at that point I replaced the broil element at the same time. Not a easy job at all.

I ordered part at 10am on Monday and part arrived at Noon on Tuesday 24 hours WHAT MORE can I say... It was all easy and now I have to cook again, so much for the stove is broken excuse.

Fue muy facil desconectar primero la estufa despues quite los tornillos de la parte superior detras de la estufa, desconecte un cable del switch y lo conecte en el nuevo despues el siguiente hasta conectar todos los cables en el nuevo switch. Lo mejor es desconectar uno por uno para mo mesclar los cables , despues removi el switch de la e ... Read more stufa y puse el nuevo , puse las partes de regreso y listo conecte la estufa t revise si funcionava el quemador y listo sin ningun problema.

Turn off the power at the breaker. Use hex head bit from 4 in one screwdriver or 1/4 inch nut driver. Heating element comes out, take off wire clamps and install new piece. Put screws back in, turn breaker on and that's it!

Removed bolts unplugged unit then plugged new unit in. Put bolts in and unit works great.

UNPLUG the oven. Following what every else was doing, I removed the element first, then disconnected the contacts. The leads on the contacts are not overly long, so I found myself removing cover on rear of oven when reconnecting red and yellow wires. Required removing two more screws with nut driver. Should I have to replace another elem ... Read more ent, I would remove rear cover first, unplug wires from element, remove element. Reverse procedure with new element.
While waiting for new element, be careful when turning on stove top element. Don't turn on oven by mistake, and when you do it, turn it off as fast as you can.
If you use stove top while waiting for part, don't forget to UNPLUG the oven. Won't be but a day or two. Very happy customer.

I was so sick of this drawer and I over heard a buddy telling a story about a website that you can get ANY piece for appliances. I take the drawer out, look up the website (partselect.com) look at the appliance diagram and find the missing piece. Order it, get it, install it. My wife thinks I'm a hero and I think I'm pretty cool too.

Very was ti replace racks and knobs. Very fast mail service

Remove drawer by pulling out and lifting up so drawer will slide out of range. Use 1/4 inch Nutdriver or socket - remove the screw that holds the drawer support to the body of the range. Remove support and install new one with screw Pay attention to the way the support fits. There are two holes one for the screw and the other for the plas ... Read more tic prong on the bottom of the support. The prong fits in the bottom hole and the screw in the above hole.