- Home
- JCB730DF1BB
- Instructions
JCB730DF1BB General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
broken light socket
-
James from Monterey, TN
- Easy
- 15 - 30 mins
-
Nutdriver
The only tool needed was a nutdriver to remove the lamp socket. I needed my head mounted light to see what I was doing, and everything went smoothly from there. Simple job.
Was this helpful?
Thank you for voting!
Bad Burner
-
Roosevelt from Waggaman, LA
- Really Easy
- 15 - 30 mins
I simply removed the 2 anchor screws in front of the stove and wrote down the wiring order on the instillation diagram, removed the old burner, removed the two studs, made sure they were installed on the right numbers place them in the new burner, wired the new burner, placed the springs respectively. Placed them in the correct holes in
... Read more
the frame to be sure that the burner was aligned properly. Put the washers on the studs and replaced the frame screws, lowered the cook top and returned the screws to lock the cook top in place.
Read less
Was this helpful?
Thank you for voting!
Drawer glider broke about a year ago.
-
loma from Neah Bay, WA
- Easy
- 15 - 30 mins
-
Screw drivers
My wife could open and close the drawer without too much difficulty, but occasionally, it would not close properly and she would have to empty the contents do could alaign it properly to close. The last time she was talking about buying a whole new drawer. I asked her what the part looked like, as I never to fight with it. I went online a
... Read more
nd found the part for $1.16 plus shipping at $8 plus. It was well worth the time and effort, and I now have a happy wife. Paul Parker
Read less
Was this helpful?
Thank you for voting!
Replacment of burner control switches
-
Judith from Keezletown, VA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
I watched your video on the subject and followed it exactly. It explained everything I needed to know. The hardest part was CLEANING under the stove once I pulled it out from the wall!
Was this helpful?
Thank you for voting!
Plastic glide broke
-
Mary Ann from Granby, CT
- Really Easy
- Less than 15 mins
-
Screw drivers
The person I spoke to knew exactly what I was trying to describe. The part arrived in 2 days. 5 minutes later the drawer was back in place. I was glad I save the screw as the part did not come with one.
Was this helpful?
Thank you for voting!
Heating Element Burned out
-
Rick from Tombstone, AZ
- Really Easy
- Less than 15 mins
-
Nutdriver
The task was very easy. After recieving the replacement I removed 2 small hex head screws using a nut driver. I pulled the slip on connectors apart the reversed the steps. I was done and able to use the oven in less than minutes.
Was this helpful?
Thank you for voting!
8 inch burner was burnt out
-
Luis from Kissimmee, FL
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
replacement was easy. pulled away the stove from wall. unplug the stove. open oven door. remove the two hex head screws holdings stove top. raise the stove top in the front. supported stove top with a 16 inch piece of wood. place New Burner under old burner. remove old burner remove wires remove old burner and place it on top of new burn
... Read more
er connected the wires from burner to new burner. install new burner. remove support lowered top down. plugged in stove tested. .burner. burner w.ork fine. reinstall hex head screws back top. pushback stove back into the wall. testes over again. all the stove work done.
Read less
Was this helpful?
Thank you for voting!
Oven light wire broken, damaged socket
-
Patricia from Brandenburg, KY
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers
Remove light bail, glass cover held by two nut screws. Pull socket, removed clips in back, replaced wire connectors, placed new socket in, then glass cover and bail. Wire connected in back, cover plate replaced.
Was this helpful?
Thank you for voting!
Open Switch
-
John from Denham Springs, LA
- Really Easy
- Less than 15 mins
-
Screw drivers
Pull knob. Pull wires. Pull two screws. Replace switch
Was this helpful?
Thank you for voting!
Orange light "Hot Stovetop" lense broke off.
-
John from Woodbridge, VA
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Parts arrived in record time and the right parts. The detailed diagram was so helpful in finding exactly the part I needed to order. Was so easy my girlfriend with no mechanical or electrical experience completely helped me through the entire project. She secured the electrical breaker to the range, and I had the top back to the oven r
... Read more
emoved. I showed her how the little white box simply slides off the lens cover, then replaced the new one in the holes and slide it back on. Secured the back and she turned on the breaker back on...and all lights work. Thanks for making this project easy, simple and quick.
Read less
Was this helpful?
Thank you for voting!