EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

JCB710DM1WW General Electric Range - Instructions

All Instructions for the JCB710DM1WW
121 - 135 of 368

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Bake unit caught fire and a 3 inch section burned away
1 person found this instruction helpful.
  • Mark from Comstock Park, MI
  • Really Easy
  • Less than 15 mins
  • Socket set
Becuase of the fire we had used a chemical based fire extinguisher, which made a real mess in the whole main floor of the house. I removed the oven from the house and used a leaf blower to get rid of all the white chemical powder (like a baking soda of sorts). Once that issue was done, I removed the part in less than 5 minutes. Two scr ews to remove it and then unpluged the two wire clips from the back of the stove under the shield which also had 6 screws to remove. It took only 3 days to have a new one delivered and I installed it in less than 5 minutes. The oven works fine now. It took much longer to clean the house than fix the oven.
Was this helpful?
Thank you for voting!
Burner burned out
1 person found this instruction helpful.
  • Daniel from Norborne, MO
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Very easy. Unpluged range from outlet, took two screws from the front under side of the range top, raised cook top up, took off four wires from burner, removed two screws than holds burner on cook top, replaced with new burner, installed two screws that hold burner in place, installed the four wires to burner, lowered cook top back into place replaced two screws that hold cook top down, pluged back into outlet. DONE!
Was this helpful?
Thank you for voting!
Bake unit started on fire then cracked in half.
2 of 4 people found this instruction helpful.
  • Sachin from Omaha, NE
  • Easy
  • Less than 15 mins
  • Socket set, Wrench (Adjustable)
We ordered the part from PartSelect and received it the next day. Didn't even have to move the range out from the wall. Just unscrewed the two screws on the back wall of the stove that hold the bake element in place with a socket wrench, then pulled the old bake element and wires out about 2-3 inches so we could disconnect the old bake unit. The element was kind of hard to pull out, but after you pull it from the wires, just plug in the new bake unit, push the wires back in and put the screws back in. Oven was up and working again!
Was this helpful?
Thank you for voting!
Lower bake element burned out
1 person found this instruction helpful.
  • Belinda from Rockford, IL
  • Really Easy
  • Less than 15 mins
  • Nutdriver
I didn't know anything about this repair, other than I was replacing a part, so it never occurred to me that I needed to make sure there was no power to the oven. When I pulled the element out, there was a large spark. I flipped the breaker off, then finished the R&R.

Make sure you turn power off at the breaker, then replace the element.

Tim
Was this helpful?
Thank you for voting!
The storage drawer came without supports.
2 of 4 people found this instruction helpful.
  • Dock from Aurora, CO
  • Really Easy
  • Less than 15 mins
  • Nutdriver
I just removed the drawer and installed the rear supports as instructed on paper included with the part.
Was this helpful?
Thank you for voting!
Baking element broke
1 person found this instruction helpful.
  • Veronica from PORT ORCHARD, WA
  • Very Easy
  • Less than 15 mins
  • Wrench set
Opened the box removed old element with socket put new one in tightened and voila ?? Just in time for thanksgiving ??
Was this helpful?
Thank you for voting!
Burned out
1 person found this instruction helpful.
  • Dean from Elkton, FL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Remove two screws to loosen the ceramic top....prop top open and change part...the part was exactly the same...change wires from one to the other and transfer clamps.....1st grade craft class would have done it in half the time I did......you folks have your parts inventory and description application to a science.....God Bless
Was this helpful?
Thank you for voting!
THE FACE PLATE IS HARD TO GET OFF THE OLD CONTROL BOARD. USE A THIN KNIFE
1 person found this instruction helpful.
  • Melvin from WEBSTER, TX
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
THE INSTRUCTIONS THAT COME IN THE EMAIL ARE VERY GOOD. BE SURE TO TAKE A PICTURE OF THE WIRING.
Was this helpful?
Thank you for voting!
burner didn't work
1 person found this instruction helpful.
  • Richard from Coon Rapids, MN
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
lift stove top, 2 undermount screws. Then unplug 4 wires, I did them 1 at a time plugging into new burner as I go so I wouldn't screw up. Take 2 screws out of old burner to stove top, # all around circle put screws in same # on new burner.Done Good experience all the way around. Order delivery and install
Was this helpful?
Thank you for voting!
Lower heating element broke and burst in flames
1 person found this instruction helpful.
  • Heinz from Colleyville, TX
  • Easy
  • 15 - 30 mins
  • Nutdriver
On the website, the heating element looked exactly the same with same measurements as the old one. However, the part I received did not match. The screw holes where the element attaches to the back were wider apart and higher. Plus, the leads curved up instead of being straight.
Was this helpful?
Thank you for voting!
Plastic guide Broken
9 of 25 people found this instruction helpful.
  • NICK from Vernon, CA
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
replaced Plastic Guides
Was this helpful?
Thank you for voting!
Replaced oven door gasket
1 person found this instruction helpful.
  • Paul from JACKSONVILLE, FL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Remove old stained gasket and replaced with new. Only $57.00!
Was this helpful?
Thank you for voting!
Bottom element fell apart
1 person found this instruction helpful.
  • david from Cromwell, CT
  • Easy
  • 15 - 30 mins
  • Screw drivers
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. ordered the part and connected the element back to the two wires replaced the two screws plugged in the stove turned on the oven and we were back in business,
Was this helpful?
Thank you for voting!
Heating element literally blew apart during use one. We have no idea why,
1 person found this instruction helpful.
  • Jon from Fort Worth, TX
  • Easy
  • 15 - 30 mins
  • Screw drivers
First, pulled out the old heating element and all the peices that were left after it fell apart. Since when you pull out the old one, the wires it connects to tend to recess back into the oven wall, I had to pull out the oven and take the back cover off in order to push the wires and connectors back through the receptacle in the oven. T his was really easy as you only have to remove 5 screws from the middle panel on the back of the oven rather than the entire oven back. Once the wires were back through, I just plugged in the new unit. The oven works just like new now. I'm sure I was able to save between $75 to $100 just for the service call by doing this myself.
Was this helpful?
Thank you for voting!
Oven heater coil burned out
1 person found this instruction helpful.
  • David from Canterbury, CT
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Removed power plug- disconnected wire, removed cover over wires two screws, and removed old heated strip, held in by two screws inside of oven
Slide in new coil installed two screws, connected two wires replaced guard over wires, plugged in stove, cooked a rubarb pie, success
Was this helpful?
Thank you for voting!
All Instructions for the JCB710DM1WW
121 - 135 of 368