- Home
- JCB635SF1SS
- Instructions
JCB635SF1SS General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The bottom burner melted
0 of 1 people
found this instruction helpful.
-
Linda from Virginia Beach, VA
- Easy
- 15 - 30 mins
-
Pliers
First we removed the screws inside the oven. Next, the oven backing was removed by unscrewing one side and one bottom bolt which exposed the clips for the burner. The clips were removed from the old burner. The old burner was pulled through the fiberglass protection and out of the oven. The new burner was inserted into the oven and the
... Read more
prongs were pushed through the fiberglass protection. The screws inside the oven were reattached. The clips were attached on the outside of the oven. The backing was slid into the right holding piece and the bolts on the left and bottom were attached.
Read less
Was this helpful?
Thank you for voting!
bakeing element burned out
0 of 1 people
found this instruction helpful.
-
Bob from Surry, VA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Removed to screws on bracket and sliped the element out. Inserted new element and installed bracket and two screws.
Was this helpful?
Thank you for voting!
The element started to spark and actually broke into two pieces.
0 of 1 people
found this instruction helpful.
-
Joe from Austin, TX
- Very Difficult
- 15 - 30 mins
-
Nutdriver, Pliers
I have a GE Profile oven and the heating element on the bottom broke in two. I found the part on your website very easily. It was easy to see that I had the correct part. I ordered the new element and it came in about three days. I easily took off the old element, but I was really surprised because the new one didn't fit. The heating
... Read more
element itself was the correct size, but the holes didn't quite match up. As a matter of fact I had to take some tin snips and expand the hole at the back of the oven. That was the only hard part, but it was really difficult to lean in that far without putting too much weight on the door. Anyway, I opened the hole about an inch more, plugged it in, and now it works perfectly!
Read less
Was this helpful?
Thank you for voting!
eye wouldnt come on
0 of 2 people
found this instruction helpful.
-
daniel from valentines, VA
- Really Easy
- 15 - 30 mins
-
Nutdriver
removed the top section on stove and removed the wires off swtitch and put on new one then put new switch in
Was this helpful?
Thank you for voting!
burner was inoperative
0 of 2 people
found this instruction helpful.
-
bryan from cocoa, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
verified switch operation , checked continuity of burner element found open ordered new part and installed next day
after extremely fast
service from partselect thank you
after extremely fast
service from partselect thank you
Was this helpful?
Thank you for voting!
light keep burning out in oven.
2 of 8 people
found this instruction helpful.
-
john from Mc Kees Rocks, PA
- Really Easy
- 30 - 60 mins
-
Nutdriver
Remove the door. Just open a little and pull up. Removed racks. Removed 3 screws with nutdriver. Pulled out housing. Disconnected 2 wires. Assembled new housing with with bulb receptacle and gasket. Reconnected wires and crimped a little to make them snug. Pushed housing back into hole. Put 3 screws back in, inserted bulb and cover. Slid
... Read more
door back on and done. 30 minutes at most.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Burner not heating.
1 of 5 people
found this instruction helpful.
-
Jack from Greensboro, GA
- Really Easy
- 30 - 60 mins
-
Screw drivers
Isolated to control switch.
Replaced
Replaced
Was this helpful?
Thank you for voting!
Light burnt out.
2 of 8 people
found this instruction helpful.
-
Roscoe G from ROCHESTER, NY
- Very Easy
- Less than 15 mins
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this helpful?
Thank you for voting!
Orange light "Hot Stovetop" lense broke off.
-
John from Woodbridge, VA
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Parts arrived in record time and the right parts. The detailed diagram was so helpful in finding exactly the part I needed to order. Was so easy my girlfriend with no mechanical or electrical experience completely helped me through the entire project. She secured the electrical breaker to the range, and I had the top back to the oven r
... Read more
emoved. I showed her how the little white box simply slides off the lens cover, then replaced the new one in the holes and slide it back on. Secured the back and she turned on the breaker back on...and all lights work. Thanks for making this project easy, simple and quick.
Read less
Was this helpful?
Thank you for voting!
Oven light wire broken, damaged socket
-
Patricia from Brandenburg, KY
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers
Remove light bail, glass cover held by two nut screws. Pull socket, removed clips in back, replaced wire connectors, placed new socket in, then glass cover and bail. Wire connected in back, cover plate replaced.
Was this helpful?
Thank you for voting!
Old bake element burned out
-
Thomas from Hamilton, VA
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers
Turned off circuit breaker, removed screws holding old element in with nut drivers, pulled out old element about 3-4" to reach terminals connected to back of element, removed spade lug terminals with needle nose pliers. Reconnected terminals to new element and screwed new element in place with nut drivers. Turned on circuit breaker and
... Read more
oven. New element works perfectly. Took about 8-10 minutes. Very easy to do.
Read less
Was this helpful?
Thank you for voting!
8 inch burner was burnt out
-
Luis from Kissimmee, FL
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
replacement was easy. pulled away the stove from wall. unplug the stove. open oven door. remove the two hex head screws holdings stove top. raise the stove top in the front. supported stove top with a 16 inch piece of wood. place New Burner under old burner. remove old burner remove wires remove old burner and place it on top of new burn
... Read more
er connected the wires from burner to new burner. install new burner. remove support lowered top down. plugged in stove tested. .burner. burner w.ork fine. reinstall hex head screws back top. pushback stove back into the wall. testes over again. all the stove work done.
Read less
Was this helpful?
Thank you for voting!
Total Burn Out Of Original Broiler Element
-
richard from Palm Coast, FL
- Really Easy
- 15 - 30 mins
-
Pliers, Socket set
Remove lower drawer and contents. Unplug unit. Tilt range on its back for easy access. Tie open oven door to forward legs with sturdy rope. Use small socket to remove 2 back screws and 2 forward element hanger screws. Detach broiler element connections from wire clips(2). Insert new element, attach 2 new connections to clips first.
... Read more
Install back socket screws. Install front socket screws for element hanger. Slide in oven shelves. Release oven door rope. Lift range to normal position. Replace lower drawer. Plug 220 in. Test oven element then broiler.
Read less
Was this helpful?
Thank you for voting!
broiler element burned completely out
-
Raymond from Highland, MI
- Really Easy
- 15 - 30 mins
-
Pliers, Socket set
Moved stove out away from wall .Unplugged stove, turned gas off. Unit is a dual fuel convection. Burners are gas, oven is electric. Removed 4 screws from back shield and exposed the 2 electrical leads connected to broiler element. Disconnected the electrical .Inside oven I removed the front bracket holding element in place, then removed t
... Read more
he 2 1/4 screws in the back holding element in place. placed new element in and finger tightened the 2 screws, next I installed the front bracket and finger tightened those. I then snugged the rear screws in followed by the front. I went to the back and reconnected the 2 electrical leads. Replaced back shield and plugged unit in and turned gas back on.Caution; Make sure your gas line is flexible before moving your stove out to far. Repair was very easy
Read less
Was this helpful?
Thank you for voting!
Baking element burned out.
-
Gary from Port Gibson, MS
- Really Easy
- 15 - 30 mins
-
Nutdriver
Turn off power to oven. Removed the rack. used a 1/4" nut driver and removed the two screws holding the element to back of oven. Slid the element out, unhook the two wires clipped to the end of the element. Replaced it with the new element, installing it in reverse. Took about 15 min. Rememer to turn off power to oven before attempting t
... Read more
o work on it.
Read less
Was this helpful?
Thank you for voting!