JBV42G2H2 General Electric Range - Instructions

I've been looking for an 8" replacement burner for my GE stove after my original burner caught on fire over a year ago. I had all but given up on finding a replacement after searching at all the stores in my area and also searching on the net. After cooking sides for Thanksgiving dinner this year and the pain of cooking with only 1 large ... Read more burner, I decided to search again for a burner on line and thank goodness I found this site! All I did was put in the model number of my range/stove and the site directed me to the replacement burner. The picture of the burner looked like mine, so I decided to purchase it but I still wasn't convinced it would fit and work because of my failed previous burner purchases. I really thought my burner was too old and the part was no longer made. Well the part shipped very quickly and lo and behold it fit and worked! Installing was a breeze...I just snapped it in...thanks so much!

I pulled the old burner out and slid the new one in it's place. Turned on the eye to make sure it worked. Felt heat in a few seconds and turned off.

I simply pushed the new burner into hardware. I then tested it to see if it works. . .

Remove the element and pan. Unscrew the bracket holding the old terminal. The terminal has adequate wire to pull out. Found area where insulation wasn't brittle. Cut old wires and stripped them to expose 1/2 inch of wire. Attached wires from new terminal with wire nuts. Placed heat-shrink tubing over each assembly and shrank it with a ... Read more heat gun. Retained the bracket from the old terminal, since it looked like it would hold the terminal assembly a bit more firmly than the new bracket. Reassembled in reverse order. Presto -- once again disappointing my wife in her desire for new appliances!

disconnected electricity, used pinch pliers to remove broken ends from connection box and used an already existing element to make sure a new one would work at all. Ordered new one that arrived very quickly and replaced the broken one. After years of taking these in and out for cleaning by outside cleaning help they are bound to break off ... Read more . I will do the gentle removal from now on.

Removed old burner, plugged in new burner. Turned on electric and everything worked fine. I was concerned that I would not be able to get the correct burner since my stove is approximately 30 years old and General Electric no longer stocks replacement parts. The new surface element was manufactured by General Electric and had the corre ... Read more ct replacement number on the package. Thanks Part Select.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

I logged into GE's website, put in my stovetop's requirements for size and type of trim rings, and was taken to partselect's site where I found what I needed. I ordered it and it came in less than a week!

After checking at local appliance stores and unable to find the bunner I went online looking. I found this site and there it was. I ordered it, received it within two days, took the old one out and the new one in. As my granddaughter says, "easy peasy lemon squeeze". It took all of five seconds and I'm cooking again.

it was hard to figure out the instructions from A switch to B switch to my switch. The first switch was no good the second one was good. prayer book didn't hurt.thank

Simple repair. Easy to do. It was disappointing to receive replacement parts which were not ceramic terminals as depicted and described in words, but plastic and therefore will need to be replaced again soon. In addition the shrink tube was not large enough in diameter to cover the wire nut, both of which were provided with the replaceme ... Read more nt terminal. Part # PS232646 is not ceramic, but plastic which does not fair well in high heat applications.

Had one burner that was completely out as the old terminal block had a broken contact. The other burner was intermittent and would arc when heating up. There are several slightly different size terminal blocks. I had a hard time re-inserting one of the old burners into the new terminal block but got it to seat. I put a new burner with ... Read more the new block on the other one and it fit much better. Additional tools used were a wire stripper and a heat gun for the heat shrink. The stove works great now.

Pulled out the 8 inch surface element and then used a 1/4 inch socket to remove mounting screw for terminal block and pulled out block with attached wires as far as wires would permit. My range top does not lift up so I had to work thru surface opening but there was at least 10 inches of wire to pull out so it was not a problem. Cut exi ... Read more sting wires at block, stripped 1/2 inch of insulation using my wire stripper pliers and wrapped wire ends of new terminal block and secured with wire nuts provided. Slipped on shrink insulation provided and applied flame from a hand held butane lighter. The instructional video on the web site was a great help. I may not have done repair without first watchng how easy it is. A cheap wire stripper is a great help. This supplier made it easy to select parts with fast delivery and complete the repair. Great source of appliance parts.

Remove oven door, removed Phillips head screws on perimeter of oven chamber, loosened four or five square head screws to facilitate the removal of the old gasket, (this gave enough room/play to pry the oven chamber slightly) then removed the old gasket, and re-assembled the oven, and replaced the door.

The only tool needed was a nutdriver to remove the lamp socket. I needed my head mounted light to see what I was doing, and everything went smoothly from there. Simple job.