JBV42G103 General Electric Range - Instructions

Simply unplug old unit and plug in the new. Easy

I turned off the circut breaker and disconnected the old terminal block - some difficulty removing the wires because of corrsion - I was able to reconnect the wires to the new block quickly and I was done - fast and easy - so happy to have found the part so easily with your program. Thank you

Replacement element also failed to heat.

Possible that the problem is with the stove itself, not with the surface element.

Just pull out the current element and plug-in the new one. Part was received in 24 hours.

1. Went on line to your website.
2. Ordered the parts
3. Rec'd your package.
4. Installed ("plugged in") the new parts.
5. Voila !

Replaced old drip bowls with the new ones. Very simple, no tools required.

it was hard to figure out the instructions from A switch to B switch to my switch. The first switch was no good the second one was good. prayer book didn't hurt.thank

The only tool needed was a nutdriver to remove the lamp socket. I needed my head mounted light to see what I was doing, and everything went smoothly from there. Simple job.

Good directions

The original controls were different for the small burners and the large burners. The replacement part fits all. Before removing wires, pay attention to writing on new and old control and replace 1 at a time. The hardest part was being sure to cut the knob stem to the correct length. Control works well.

Remove oven door, removed Phillips head screws on perimeter of oven chamber, loosened four or five square head screws to facilitate the removal of the old gasket, (this gave enough room/play to pry the oven chamber slightly) then removed the old gasket, and re-assembled the oven, and replaced the door.

I have had to replace this unit once before. It was very obvious which terminal had burned off. Removed the total front panel. Removed the timer and replaced wires from one unit to the other. Also had to strip off one wire connection and replaced it .

Took oven door apart to get to gasket. . . Took about an hour or less. Then I basically cleaned the entire over door while I waited for the part to come. When the new gasket came I started to put it back on. I used springed type clothes pins to hold the gasket in place on the middle part of the door which hold the glass. As I put ... Read more on the out part of the oven door over the middle part of the oven door, I carefully took the pins off as I gradually slipped the 2 parts of oven door back together. After the gaskets were carefully adjusted to it's proper position, then I put the nut screw back in through the gasket holes to hold the 2 oven door parts back together. Then, I finally put the rest of the door back together. This took about an hour also. Not to bad when you have to do this by your selves. This is the second time I've put in a new oven gasket. The oven is 28 years old, so the gaskets last me about 14 years each time. We hope to keep the oven a few more year before we buy a new glass top style stove. Hope this was helpfull to all you diy's !!! Don

This is twin oven range with controls at side of upper oven. Control panel was fastened with screws at top and bottom. Range has built-in hood at top which had to be disassembled to reach top screw. Once had access to top screw, eaisly removed control panel and replaced control. New control had identical connections as old control so ... Read more only had to install it, break shaft to correct length, and use proper shaft adapter for knob. Remounted control panel and range worked perfectly. This would have been a very quick job except for having to deal with the built-in range hood.

I flipped breaker off for electic and confirmed that power to the stove was off. I removed the 2 screws holding the control unit in place. Carefully removed all knobs and buttons and pryed the cover for the control unit off. I then removed old part, removed the wired and clipped wires to the new unit. Put cover back on - has some difficul ... Read more ty getting the panel back in place to line up the screws. But after a couple of attempts, was able to line up unit and put screws in place to secure. Replaced all knobs. Turn breaker back on and cooked lunch. Very easy job. Most difficult part was getting panel back in position. I would watch alignment more carefully before I removed in next time. Easy home repair for Women...not sure about my man?