- Home
- JBS60DF4BB
- Instructions
JBS60DF4BB General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
blew out board by crossing wires..mistakenly toke out bulb assembly to replace bad bulb
3 of 3 people
found this instruction helpful.
-
Ken from CALABASH, NC
- Very Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Turne off power to range..pulled oven out..Took top back panel off with nut driver. 4screws .. Took picture of control board....removed bad control board with Phillips driver...4 screws....installed New board...removed 1 connection at a time and replaced in New board..Turned power on to test new board...check picture to make sure connect
... Read more
ions are correct...turn off power...put back panel back on...put range back in place...turn power back o n...done ..approximate time 15 to 20 minutes..
Read less
Was this helpful?
Thank you for voting!
Hole in gasket
3 of 3 people
found this instruction helpful.
-
Cynthia from Kidder, MO
- Very Easy
- Less than 15 mins
I took the oven door off. Laid it down on a blanket on the floor. I pulled up on end going into the door, then went around with fingers to feel where the clip were and grab the clip with my fingers and gently pulled up. Then grabbed the new gasket, found the center clip that goes at top of door and started pushing the clips in. The last w
... Read more
as feeding the ends back into the slot in the door.
Read less
Was this helpful?
Thank you for voting!
Needed to replace oven door gasket
3 of 3 people
found this instruction helpful.
-
Jayne from EAST PEORIA, IL
- Very Easy
- 15 - 30 mins
-
Screw drivers
Watched youtube video. Very easy to replace
Was this helpful?
Thank you for voting!
OVEN CLOCK CONTROL MALFUNCTIONED
3 of 3 people
found this instruction helpful.
-
Gregoire from N CHESTERFLD, VA
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Wrench set
I turned off the circuit breaker and unplugged the stove. I removed the back panel and marked the location of the wires on the new oven clock control. I detached the wires and removed the old card. I installed the new one and reconnected the wires. I plugged the stove and turned on the circuit breaker. All the lights came on and the oven
... Read more
worked fine. I reinstalled the back panel and it took me less than thirty minutes to complete the job.
Read less
Was this helpful?
Thank you for voting!
Oven would not heat up
3 of 3 people
found this instruction helpful.
-
Myron from SCOTTSDALE, AZ
- Very Easy
- 15 - 30 mins
-
Socket set
Changed the lower heating element. Simple, simple, simple. I first went on YouTube and watched a couple of videos. Reassurance is a good thing. Okay here we go. 1) Pull the oven out from the wall 2) UNPLUG 3) remove the racks in the oven 4) Unscrew the (2) screws holding the element to the back wall of the oven. 5) There are t
... Read more
wo (2) connections that you simply pull off. Remove the element. 6) Throw the old heating element away and connect the NEW element where the OLD one was. 7) Put the old screws back in. Plug the oven back in and test. VOILA!!! you are now a repairman.
Read less
Was this helpful?
Thank you for voting!
Incorrect oven temperature due to defective temperature sensor.
3 of 3 people
found this instruction helpful.
-
Anthony from FARMINGVILLE, NY
- Really Easy
- Less than 15 mins
-
Nutdriver
Performed repair using a video for reference.
Was this helpful?
Thank you for voting!
When you touched any button on the controls LOC on appeared.
3 of 3 people
found this instruction helpful.
-
Roger from HUNTSVILLE, AL
- Very Easy
- Less than 15 mins
Talked to parts select tech after ordering the control board. Tech advised me that he felt the range could be repaired without installing any parts. Advised me to contact manufacture tech support and explain the problem. I did to find that the child safety lock was on, probably from cleaning and touching too many buttons at once while whi
... Read more
pping surface. Told me to hold down + and - at the same time for three seconds and it was fixed.
Parts select tech had told me don’t worry the parts are guaranteed so I called for a RMA and returned the parts for a refund. Thanks Parts Select, y’all are real professionals and that is greatly appreciated.
Thank you all.
Parts select tech had told me don’t worry the parts are guaranteed so I called for a RMA and returned the parts for a refund. Thanks Parts Select, y’all are real professionals and that is greatly appreciated.
Thank you all.
Read less
Was this helpful?
Thank you for voting!
Switch was not turning off range indicator light
3 of 3 people
found this instruction helpful.
-
Charles from PORTLAND, OR
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Pulled stove out and unplugged. At the rear of the range there were 4 faster. Used a nutdriver piece in an electric drill. Pulled off the cover and located the switch. At the front of the stove, I removed the knob and unscrewed two screws releasing the switch. I undid and replaced each wire connector one-by-one to avoid any wrong connecti
... Read more
ons. Replaced and secured the switch and replace the back panel. All secured, power on and fixed! Easy repair, but something that had been put off for a year!
Also follow the installation videos from PartSelect - very helpful!
Also follow the installation videos from PartSelect - very helpful!
Read less
Was this helpful?
Thank you for voting!
previous owner self cleaned and left oven racks in the oven
3 of 3 people
found this instruction helpful.
-
Judith from San Antonio, FL
- Really Easy
- Less than 15 mins
threw out the old ones and slide in the replacement ones from you.
Was this helpful?
Thank you for voting!
drwer slide under stove broke off.
3 of 4 people
found this instruction helpful.
-
paul from sewell, NJ
- Really Easy
- Less than 15 mins
-
Screw drivers
recieved part the next day. looked different but I followed instructions and the part worked perfect.
Was this helpful?
Thank you for voting!
burner not work
3 of 4 people
found this instruction helpful.
-
SILVIA from Midlothian, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers
Fue muy facil desconectar primero la estufa despues quite los tornillos de la parte superior detras de la estufa, desconecte un cable del switch y lo conecte en el nuevo despues el siguiente hasta conectar todos los cables en el nuevo switch. Lo mejor es desconectar uno por uno para mo mesclar los cables , despues removi el switch de la e
... Read more
stufa y puse el nuevo , puse las partes de regreso y listo conecte la estufa t revise si funcionava el quemador y listo sin ningun problema.
Read less
Was this helpful?
Thank you for voting!
front lift burner not working and surface light on with everything off
2 of 2 people
found this instruction helpful.
-
kevin from GAYLORD, MI
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
unplugged the range removed 4 screws from back top cover then took the knob off controller removed 2 screws from behind the knob removed 1 wirer at a time and placed it on the new controller in same order the wires came off put everything back to gather did not fix the problem .
Was this helpful?
Thank you for voting!
Stove overheated with an F2 error
2 of 2 people
found this instruction helpful.
-
Richard from PHOENIX, AZ
- Easy
- 15 - 30 mins
-
Nutdriver
Removed screws holding temp sensor, pulled wire out from behind wall until found connector, disconnected old sensor.
Measured resistance of old sensor and compared with new sensor, they measured nearly the same. Installed the new sensor and tested the stove. Came up to temp ok. No problem since, about 2 weeks.
Measured resistance of old sensor and compared with new sensor, they measured nearly the same. Installed the new sensor and tested the stove. Came up to temp ok. No problem since, about 2 weeks.
Was this helpful?
Thank you for voting!
Bake element shattered while cooking coating everything inside with a fine white dust
2 of 2 people
found this instruction helpful.
-
Greg from Virginia Beach, VA
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
First I searched for the part here and I had a slightly hard time finding the correct element on the site.
Then I read the comments of the others and the issues they faced.
I unplugged the range and pulled it out a bit from the wall. I then removed the two screws that hold the element in place and put them where I would not lose ... Read more them. Then I gently maneuved the element out and placed a clothespin on each of the wires to keep them from going back in and then disconnected the wires from the element using a pair of needlenose pliers.
At this point I had to gently bend the new element back into shape as it had been bent during shipping. Then I connected the wires and slid the element into place and installed the two screws.
Double checked to make sure everything was ok plugged in the range, said a quick prayer and set the temperature to 300. When it got to 300 the element shut off and I was happy that the element did not take any other parts with it.
Then I read the comments of the others and the issues they faced.
I unplugged the range and pulled it out a bit from the wall. I then removed the two screws that hold the element in place and put them where I would not lose ... Read more them. Then I gently maneuved the element out and placed a clothespin on each of the wires to keep them from going back in and then disconnected the wires from the element using a pair of needlenose pliers.
At this point I had to gently bend the new element back into shape as it had been bent during shipping. Then I connected the wires and slid the element into place and installed the two screws.
Double checked to make sure everything was ok plugged in the range, said a quick prayer and set the temperature to 300. When it got to 300 the element shut off and I was happy that the element did not take any other parts with it.
Read less
Was this helpful?
Thank you for voting!
Just didn't work no pwr to it
2 of 2 people
found this instruction helpful.
-
Jerry from HOPEWELL, VA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Killed braker first, removed four screws from back, then unplugged all the wiring, then removed four screw that hold the unit on stove, pealed off the face decal, put that on the new on and just reversed the take off press.
Was this helpful?
Thank you for voting!