- Home
- JBS60DF2BB
- Instructions
JBS60DF2BB General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
just want new parts
1 person
found this instruction helpful.
-
Minnie from hurdle mills, NC
- Really Easy
- 15 - 30 mins
-
Socket set
very easy and clean.
Was this helpful?
Thank you for voting!
Bake button stopped registering
1 person
found this instruction helpful.
-
Ryan from COHOES, NY
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers
This was simple enough to repair for me, a relative novice. Just remember you need a nut driver to take the back panel off, take a photo of the existing board so you remember which wires go where, and you definitely need a hair dryer to heat up the sticker on the old board so you can remove it and put it on the new board.
Was this helpful?
Thank you for voting!
Slow heat recovery
1 person
found this instruction helpful.
-
Edmond from BRISTOL, CT
- Really Easy
- 15 - 30 mins
-
Nutdriver
Had to remove rear cover to connect wires, removing them from the front caused the wires to fall into rear.
Was this helpful?
Thank you for voting!
BASE OF BULB BROKE OFF & WELDED TO SOCKET
1 person
found this instruction helpful.
-
NEIL from ROCKY POINT, NY
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers
PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.
Was this helpful?
Thank you for voting!
The light socket cup could no longer hold the bracket that holds the light cover in place.
1 person
found this instruction helpful.
-
Roger from ALPENA, MI
- Really Easy
- 30 - 60 mins
-
Socket set
I watched a video of a similar model to familiarize myself with the required steps needed. I opened the back and disconnected the power cord and ground wires connected to the removable socket I then removed the lightbulb and removable socket from the oven interior side. I then removed the defective light socket cup and replaced it with th
... Read more
e part I purchased. After replacing the removable socket and lightbulb, the bracket holding the light cover functioned perfectly with the new light socket cup. Final steps were to reconnect the power and ground wires to the removable socket. I then replaced the back cover over the light socket cup area. One word of advise. Be very careful when removing and reconnecting the cables to the removable light socket.
Read less
Was this helpful?
Thank you for voting!
The storage drawer came without supports.
2 of 4 people
found this instruction helpful.
-
Dock from Aurora, CO
- Really Easy
- Less than 15 mins
-
Nutdriver
I just removed the drawer and installed the rear supports as instructed on paper included with the part.
Was this helpful?
Thank you for voting!
Lower bake element burned out
1 person
found this instruction helpful.
-
Belinda from Rockford, IL
- Really Easy
- Less than 15 mins
-
Nutdriver
I didn't know anything about this repair, other than I was replacing a part, so it never occurred to me that I needed to make sure there was no power to the oven. When I pulled the element out, there was a large spark. I flipped the breaker off, then finished the R&R.
Make sure you turn power off at the breaker, then replace ... Read more the element.
Tim
Make sure you turn power off at the breaker, then replace ... Read more the element.
Tim
Read less
Was this helpful?
Thank you for voting!
Element blew hole in self then no power to burner.
2 of 4 people
found this instruction helpful.
-
Melvin from Portland, TN
- Easy
- Less than 15 mins
-
Screw drivers, Socket set
Replaced burned element, did not fix no power problem. Ordered receptor replacement, replaced it, took less than 10 mminutes, but still no power to burned. Then ordered replacement switch, replacement too less than 10 minutes again and burner works fine.
Was this helpful?
Thank you for voting!
Oven was very slow to heat
1 person
found this instruction helpful.
-
James from CANAL FULTON, OH
- Very Easy
- Less than 15 mins
-
Nutdriver
Removed the rear panel from the Range using the nut driver. pulled the terminal wires off the back of the heating element. Double checked if there was continuity across the heating element terminals before removing the element. If there is none, its bad. remove the two screws inside the oven holding the element in place. Once free, lift t
... Read more
he front of the element to about 30 degrees and pull towards you. Insert the new element in the reverse manner then secure it using the two screws. Push the terminal wires onto the terminals on the back of the element and reinstall the rear panel.
Read less
Was this helpful?
Thank you for voting!
Back element was broken
1 person
found this instruction helpful.
-
Shiirley from CASPER, WY
- Really Easy
- Less than 15 mins
-
Pliers
My son did it by using pliers. He took out the screws that held the element in and pulled it out and used the pliers to pull the wires out of the old one and snapped the new one in . put it back together. about 5 minutes.
Was this helpful?
Thank you for voting!
Bake element was burnt out.
1 person
found this instruction helpful.
-
Bertram from ABERDEEN, MD
- Very Easy
- Less than 15 mins
-
Socket set
1.Disconnect the power cord. 2.Remove two screws pull the element out. 3.Disconnect the wires attach to element. 4. Install the new element connecting the wires. 5. Align element
... Read more
with holes and tighten screws. 6. Plug in power cord and begin to cook.
Read less
Was this helpful?
Thank you for voting!
Not Reaching Temperature above 300 Degrees
1 person
found this instruction helpful.
-
Ron from SAN TAN VLY, AZ
- Very Easy
- Less than 15 mins
-
Nutdriver
Take off 6 screws of back cover of the range, unplug the white wire. Go to the inside of oven, pull out racks. At the top of the oven is your Broiler element, in the center you will see a rod sticking out with one screw holding it in place. Take out screw and pull temperature sensor out toward you. Reverse steps to put it back together.
Was this helpful?
Thank you for voting!
oven door gasket needed replaced
1 person
found this instruction helpful.
-
Mary from LONGS, SC
- Very Easy
- Less than 15 mins
Ordered the part, it arrived and 5 minutes later it a complete installation
Was this helpful?
Thank you for voting!
Bad Line fault displayed on range clock
1 person
found this instruction helpful.
-
Vincent J Paola, from GREENWEL SPGS, LA
- Very Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
1. Unplug the range power cord from the outlet.
2. Moved range away from the wall and countertop.
3.Using a nut driver removed the 2 screws on each side of the removable panel on the back side of the control knobs and clock.
4. Using a phillips head screwdriver remove 2 screws on top side of the back side panel.
5. Usi ... Read more ng a nut driver remove 4 screws that secure the main control board in place.
6. Take photo of the wiring on the main control board if not color coded.
7. My control board, and the replacement board were both color coded with the color with the wire placement on the rear of the board.
8. Remove wires with needle nose pliers.
9. Using a hair dryer, heat the plastic control panel face plate that fits onto the front of the old control board.
10.With a putty knife carefully pry the face plate from the old control board.
11. Install the control board face plate onto the new control board.
12. Install the color coded wiring in place on the back side of the control board.
13. Replace the control board into the range, and install screws, and rear panel of the range.
14. Plug cord into outlet and test range for proper operation.
2. Moved range away from the wall and countertop.
3.Using a nut driver removed the 2 screws on each side of the removable panel on the back side of the control knobs and clock.
4. Using a phillips head screwdriver remove 2 screws on top side of the back side panel.
5. Usi ... Read more ng a nut driver remove 4 screws that secure the main control board in place.
6. Take photo of the wiring on the main control board if not color coded.
7. My control board, and the replacement board were both color coded with the color with the wire placement on the rear of the board.
8. Remove wires with needle nose pliers.
9. Using a hair dryer, heat the plastic control panel face plate that fits onto the front of the old control board.
10.With a putty knife carefully pry the face plate from the old control board.
11. Install the control board face plate onto the new control board.
12. Install the color coded wiring in place on the back side of the control board.
13. Replace the control board into the range, and install screws, and rear panel of the range.
14. Plug cord into outlet and test range for proper operation.
Read less
Was this helpful?
Thank you for voting!
The heating element broke in half.
1 person
found this instruction helpful.
-
Paul from Louisville, KY
- Easy
- Less than 15 mins
-
Screw drivers, Socket set
This was a very simple procedure. I removed the 2 screws in the oven itself (holding the element in place), then pushed the element through the back of the oven so the wires were exposed, then slipped off the wires, the male end from the female end, I then removed the entire element. I put the new element in the over, re-attached the wire
... Read more
s, put the screws back in place, replaced the cover, and the oven was as good as new.
Read less
Was this helpful?
Thank you for voting!